20 Most Recent Bosch Axxis+ WFR 2460 Front Load Washer - Page 4 Questions & Answers


only brushes in motor ,he taking the mikey motor only 236.00 from bosch

Bosch Axxis+ WFR... | Answered on Jun 30, 2009


replace the main board, 

Bosch Axxis+ WFR... | Answered on Apr 24, 2009


It may just be that there is a blockage in the outflow pipe, get a bucket ready to catch any excess water and remove the outflow pipe from the sump to check if there is any blockages.

I hope this helps

Bosch Axxis+ WFR... | Answered on Mar 10, 2009


Remove rear panel and check the belt is o/k, if it is, then remove belt, undo 2 bolts that hold motor, unplug the motor connector, lever motor back with a screwdriver, and remove motor.
Check the brushes, they should be at least 5mm long, \any shorter, then replace.
Plz rate my solution.
TRhanks.

Bosch Axxis+ WFR... | Answered on Feb 04, 2009


If your washer has a removable plastic `panel at bottom front, then remove same, it may have coin operated slots to undo.
There should be a filter there, unscrew anti- clockwise, remove and clean.
Please rate my fixya solution.
Thanks.

Bosch Axxis+ WFR... | Answered on Feb 02, 2009


Try repairclinic.com  We were able to find parts for our Bosch WFK2401 washing machine and our Asko dishwasher...they list the part descriptions and show pictures.  It might take a few minutes to sift thru the things but i bet you can find your part.  FYI, shipping has been great...just a day or two to arrive after ordering.

Bosch Axxis+ WFR... | Answered on Jan 24, 2009


On the bottom right-hand side of the washer, there should be a door that contains the drain cleanout. Open the door and in the upper right-hand corner of the opening, there should be the end of a plastic handle. It may barely be showing, so look closely. Pull it down with your fingers or a plyers and your door should release.

Bosch Axxis+ WFR... | Answered on Jan 12, 2009


Hello
if your brushes are only 1/4" long, I would replace them. The symptoms sounds like worn brushes.


Bosch Axxis+ WFR... | Answered on Dec 28, 2008


are you sure it only happens in the spin cycle? and is the leak comming from the bottom front of the washer? most front laoders will leak due to a tear in the belows. that is the rubber boot that seals the washer tub to the front panel. if there was a hole or a tear in the bellows it should have a leak inthe wash cycle also. but there are also other possibilitys too.but its strange to only leak in a spin cycle due to the washer is extracting the water and not adding it. so check and see if it leaks in the wash cycle to and get back to me and we can go from there. looking through my training manual i dont see what could cause a leak in just the spin cycle

Bosch Axxis+ WFR... | Answered on Dec 01, 2008


Sounds like the motor brushes need replacing, you will have to remove the motor to do this.
Hope this helps.
Please leave feedback.

Bosch Axxis+ WFR... | Answered on Nov 30, 2008


if you have checked the plug and the fuse in the plug and they are both okay, then is could be the capacitor inside the machine and you will need to call out an engineer to repair it

Bosch Axxis+ WFR... | Answered on Oct 27, 2008


could be impeller broke off or loose on motor shaft also may be blockage in lines to or from pump and not in pump it's self

Bosch Axxis+ WFR... | Answered on Oct 26, 2008


check the filter and check for foreign object stuck in pump impellor

Bosch Axxis+ WFR... | Answered on Oct 25, 2008


I have a WFL 2060 UC on the bottom right there is a small access door. Inside the door you will find a drain plug which will unscrew counter clock wise. Water will come out so I tipped up the machine and slid a 1" deep cooking pan under the corner. When I unscrewed the plug I found a penny inside.

Bosch Axxis+ WFR... | Answered on Oct 17, 2008


it just unscrews - take a pair of pliars to it

Bosch Axxis+ WFR... | Answered on Oct 16, 2008


possibly the motor brushes.
take back panel off and motor is held in by bolts which undo - also disconnect electrical plug and socket.
check condition of brushes

Bosch Axxis+ WFR... | Answered on Oct 16, 2008


hi Many universal motor malfunctions are caused by wearing down of the carbon brushes, the soft blocks of carbon that complete the electrical contact to the motor's commutator. When these brushes become worn, the motor will spark, and electrical contact may be incomplete.try this
Step 1: To sight-check the carbon brushes, remove the screws that hold the brushes and brush springs into the brush holders at the sides of the commutator. The screws will pop out of the screw holes; turn the motor over to tap out the brushes. The ends of the brushes should be curved to fit the commutator; if they're worn down, new brushes are needed.
Step 2: To check carbon brushes with a continuity tester, remove the motor lead wires from the circuit. Tag the wires as you disconnect them so that you'll be able to reconnect them properly. Hook the tester clip to one motor lead and touch the probe to the other lead; the tester should light or buzz. Slowly rotate the motor shaft, keeping the tester in position. If the tester doesn't light or buzz, or if it flickers or stutters when you turn the motor shaft, the brushes should be replaced. If the springs behind the brushes are damaged, they should be replaced as well.

Step 3: Replace worn carbon brushes and damaged springs with new ones made specifically for the motor. The model information (number and make) is stamped on a metal plate fastened to the motor, or embossed on the metal housing of the motor. If you can't find the model information, take the worn brushes and springs with you to an appliance-parts store to make sure you get the right kind. Insert the new springs and brushes in the brush holders, replace the brush assemblies, and secure the new brushes with the mounting screws that held the old brushes.

Bosch Axxis+ WFR... | Answered on Sep 14, 2008


press the left menu button 4 times to get to the signal menu and press the right menu button until you get to OFF (for bosch maxx 2460)

Bosch Axxis+ WFR... | Answered on Sep 13, 2008


after ensuring the sump hose and transfer hoses are clear clean out the pressure system to ensure the water wash level is not more than usual, secondly check whether the waste hose is not back filling from a sink u bend and also check the sink u bend for blockages (usually fat).
if all ok start to check the wiring connections from pump to pcb board, if these are ok then there may be a fault on the board. (pumping problems are usually easily solved with the above proceedure, the pcbs are rarely at fault for bosch but you may be the unlucky one !). tony

Bosch Axxis+ WFR... | Answered on Aug 24, 2008


the pum should do that but the magnet side may have saturated with water beyond the seal. i recommend replacing the pump.

Bosch Axxis+ WFR... | Answered on Aug 21, 2008

Not finding what you are looking for?
Bosch Axxis+ WFR 2460 Front Load Washer Logo

125 questions posted

Ask a Question

Usually answered in minutes!

Top Bosch Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

jimorris77

Level 3 Expert

411 Answers

Dw Wooten
Dw Wooten

Level 2 Expert

227 Answers

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Bosch Washing Machines

  • Bosch Washing Machines

Most Popular Question

pump blocked cannot open remove cap

  • Washing Machines
Loading...