Price Pfister Hanover 950-102S Soap & Lotion Dispenser - Stainless - Answered Questions & Fixed issues
Soap dispenser replacement
Best thing to do is contact Price Pfister directly. If there is a problem with the dispenser or there is a faulty part, they are usually pretty good about replacing their stuff at little or no cost to you, their customer.
Soap dispenser doesn't pump soap
Price Pfister has a 800 number that you can call if you are having problems. If they can not fix it, they offer a life time warranty on most products that they make. They will usually send out a replacement for it if they can not solve your problem.
Price Pfister Shower--No water to shower
Does the tub spout water flow stop when the shower knob is pulled?
Was the systems pipping flushed before the shower head was installed?
It may be clogged, remove the shower head and then attempt to operate. If it is clogged you will see debris trapped in the screen at its connection point. The shower head can be disassembled - cleaned - reassembled
Is the shower head an adjustable type, that may be in the off position?
Good luck
Aduz
3/26/2009 4:38:27 PM •
Price Pfister...
•
Answered
on Mar 26, 2009
•
1,080 views
How to reversing stem rotation for Pfister 910-030 cartridge
For Pfister 910-030 tub stem: Take off the 1/2 white clip at the end of the post, it's next to the 12 splines that hold the handle on. Its a little tight but can be done after the stem is installed. Flip it over and slip it back on aligning the notches properly first. A 2" long 13 mm socket slipped over the end and tapped lightly with a hammer helped me get it set.
11/13/2021 5:09:55 PM •
Price Pfister...
•
Answered
on Nov 13, 2021
•
1,171 views
If we put the wax
If you are installing a wax (doughnut) seal to connect the toilet to the main drain, then the wax ring should be big. It should 'squish' to seal correctly. You may not need it, but I've known plumbers to install two of the seals at once for extra gap-filling. Just install the seal, sit on the toilet to compress the seal into place and then install the bolts to the floor. Done!
How to clean the screen filter in the kitchen faucet
I don't know your exact model but most faucets screen filter can be screwed off for cleaning or replacement. Remove the screen filter with a pair of pliers and a rag. Once you get it loose, you should be able to unscrew with your fingers. Put the rag around filter before putting the pliers on it to prevent gouges and deep scratches in the chrome. IF you have a dishwasher, you can clean the screen filter on top basket of dishwasher if you have one. IF the screen filter looks bad to you, just replace it. Go to any hardware store ,take the screen filter with you and get help finding the right one. Once you have a replacement, hand screw it back on as tight as you can. IF it still leaks , use the rag and pliers to tighten it just enough to stop the leak in the screw parts. Good luck.
How do I remove a Pfister Marielle metal lever handle?
Bear with me, please. Adjust the temp at the physical valve?
Interesting at the least. Never seen or heard of that. They come up with something new everyday. I'm going to follow this for my own benefit. Thank you. And good luck. - Ned
Can I remove the screen filter in the kitchen
Yes, the aerator (where the water comes out) can be unscrewed and removed from the faucet. I remove these and clean them out on a regular basis. If the aerator won't unscrew by hand, place a washcloth over the aerator (to prevent scratching) and carefully turn it with a pair of pliers. (Screw direction to loosen: Looking down on faucet, with pliers to the right-hand side, pull them toward you.) Make sure the rubber washer is properly placed in the top of the aerator after you have cleaned it out and you go to screw it back on. You normally don't need pliers to put it back on, as these are meant to be screwed on hand-tight. There might be several little parts inside the aerator to take apart and clean out, so be very careful to put these parts back together the same way they came apart. I find a toothpick is often useful to clean these out, as well as a cup of water to rinse them in.
12/28/2012 6:10:19 PM •
Price Pfister...
•
Answered
on Dec 28, 2012
•
3,656 views
Water coming from single shower handle
It may just be a screw loose or you may need to check the washer and o-ring inside. Dont take anything apart if your not comfortable in doing that. Get someone who does.
How do I change the hot water setting on a new
HELLO- This type of valve has a two piece catridge,you will have to adjust it till it reaches the hot water inlet. A little tricky but you can do it, be sure to shut water off to shower!!!!! Good luck.
Have single knob series 09
1. Remove Handle Assembly (9A)
2. Unscrew Retainer Sleeve (9B)
3. Remove Flange (9C)
4. Remove Stem and Bonnet Assembly (9D)
5.
Pull out Balancing Cartridge (9E)I hope that answers your question.
I have a price pfister
I would say it is a washer on the stem, here is a website that will assist you:
http://www.pricepfisterparts.net/
Not finding what you are looking for?