Top 20 Price Pfister Hanover 950-102S Soap & Lotion Dispenser - Stainless Questions & Answers

Best thing to do is contact Price Pfister directly. If there is a problem with the dispenser or there is a faulty part, they are usually pretty good about replacing their stuff at little or no cost to you, their customer.

Is the trap and drain not installed yet? If there is no plumbing to drain into then I would siphon or pump it out into buckets.

Does the tub spout water flow stop when the shower knob is pulled?

Was the systems pipping flushed before the shower head was installed?

It may be clogged, remove the shower head and then attempt to operate. If it is clogged you will see debris trapped in the screen at its connection point. The shower head can be disassembled - cleaned - reassembled

Is the shower head an adjustable type, that may be in the off position?

Good luck
Aduz

Price Pfister has a 800 number that you can call if you are having problems. If they can not fix it, they offer a life time warranty on most products that they make. They will usually send out a replacement for it if they can not solve your problem.

If you are installing a wax (doughnut) seal to connect the toilet to the main drain, then the wax ring should be big. It should 'squish' to seal correctly. You may not need it, but I've known plumbers to install two of the seals at once for extra gap-filling. Just install the seal, sit on the toilet to compress the seal into place and then install the bolts to the floor. Done!

you need a new tank kit, pick one up at your local Menards

Bear with me, please. Adjust the temp at the physical valve? Interesting at the least. Never seen or heard of that. They come up with something new everyday. I'm going to follow this for my own benefit. Thank you. And good luck. - Ned

I don't know your exact model but most faucets screen filter can be screwed off for cleaning or replacement. Remove the screen filter with a pair of pliers and a rag. Once you get it loose, you should be able to unscrew with your fingers. Put the rag around filter before putting the pliers on it to prevent gouges and deep scratches in the chrome. IF you have a dishwasher, you can clean the screen filter on top basket of dishwasher if you have one. IF the screen filter looks bad to you, just replace it. Go to any hardware store ,take the screen filter with you and get help finding the right one. Once you have a replacement, hand screw it back on as tight as you can. IF it still leaks , use the rag and pliers to tighten it just enough to stop the leak in the screw parts. Good luck.

For Pfister 910-030 tub stem: Take off the 1/2 white clip at the end of the post, it's next to the 12 splines that hold the handle on. Its a little tight but can be done after the stem is installed. Flip it over and slip it back on aligning the notches properly first. A 2" long 13 mm socket slipped over the end and tapped lightly with a hammer helped me get it set.

remove cartridge blow out water lines be careful

It may just be a screw loose or you may need to check the washer and o-ring inside. Dont take anything apart if your not comfortable in doing that. Get someone who does.

You can buy the 900-259 part on the links below.

http://www.efaucets.com/detail.asp?product_id=900-259&KID=343471468788241705&gclid=CPW24ves5KkCFQ9VgwoddlJn8A

http://www.lockeplumbing.com/detail.asp?c=Faucet%20Parts%20P%20through%20R&s=Price%20Pfister&s2=&sku=PRI-900-259-260&r1=WHE-USS25C&r2=GRU-595916&r3=FEI-NL9-LED

If you are in Los Angeles and not to far from Orange where I am, You will want to go to biard and crockett plumbing. They will have it in stock. They are 10 mins from disneyland. Here is there web site and address below.

http://www.bcpsi.com/

1. Remove Handle Assembly (9A)
2. Unscrew Retainer Sleeve (9B)
3. Remove Flange (9C)
4. Remove Stem and Bonnet Assembly (9D)
5. Pull out Balancing Cartridge (9E)

I hope that answers your question.

HELLO- This type of valve has a two piece catridge,you will have to adjust it till it reaches the hot water inlet. A little tricky but you can do it, be sure to shut water off to shower!!!!! Good luck.

replace the diverter valve washer and seat

Next time you go to the hardware store bring a pad of paper and a pen.

Maybe he is not the sharpest tool in the shed, you need to call a plumber!!!!!!

If this is what your unit looks like and you want the handle to be in this position when closed then you need to loosen the handle (small set screw on the handle) and repossession it where you want it be in the closed position and snog the set screw down.

See instructions here
http://pricepfisterparts.faucetdirect.com/mediabase/specifications/8P8-PD_INSTALLSHEET.pdf

Yes, the aerator (where the water comes out) can be unscrewed and removed from the faucet. I remove these and clean them out on a regular basis. If the aerator won't unscrew by hand, place a washcloth over the aerator (to prevent scratching) and carefully turn it with a pair of pliers. (Screw direction to loosen: Looking down on faucet, with pliers to the right-hand side, pull them toward you.) Make sure the rubber washer is properly placed in the top of the aerator after you have cleaned it out and you go to screw it back on. You normally don't need pliers to put it back on, as these are meant to be screwed on hand-tight. There might be several little parts inside the aerator to take apart and clean out, so be very careful to put these parts back together the same way they came apart. I find a toothpick is often useful to clean these out, as well as a cup of water to rinse them in.

I can think of a few possibilities. 1) Something is blocking the hot water in to the mixing valve. Fixing this would probably mean cutting out the valve (then redoing the water lines with a new valve (possible option)).

2) The hot water line is losing too much heat going to this second faucet. (If the two tubs are on different floors this is more common. Many places are plumbed with one line with Ts to all fixtures.) Insulating the water lines might help; alternatively an point of use water heater would help.

3) The hot water and the cold water in are reversed. (Test by leaving the water on full cold and full hot for a few minutes each.) If you get full hot when it should be cold, valves with a cartridge are easy to fix. Open the valve assembly, remove the cartridge and reinsert it after turning it around (side closest to you when you removed it goes in first). Otherwise, the incoming plumbing needs to be redone at the point where the cold and hot lines come into the shower.

I hope this helps.

Cindy Wells