Top 20 Braun M880 MultiMix Hand Mixer Questions & Answers

I'm afraid the gears inside are worn off. But perhaps it is worth to open the mixer, to see if perhaps only a screw came lose, so the slip comes from there. If you are not technical don't try this yourself.

http://www.user-manual-pdf.com/appliance/handmixer/braun/instruction/braun-multimix-4642-handmixer.html

HI.This steps might be as well helpful.let me just clarify that you can't even manually twist the shafting.If the motor is working an yet it will not turn the shaft.Tha shafting bossing might as well been broken misallign inside..Better remove the cover by unscrewing it and then try to observe how the motor works.If it really does turn when ever it is plugg on to the source.Observe also misallign bosssing that connects the shafting and the motor's rotor.Thank you for choosing FIXYA.

Hi
Make sure you use the pulse function of the power switch. Only this position (forward, away from you) will activate the immersion blender, and then at full speed only.

I very much doubt if you will be able to purchase the hand unit on its own, and I also doubt if there will be any great saving in doing this.

motor us ..no good change motor...07779933829 uk

You start it by pushing the switch lever forward, and you need to hold it there for as long as you want it to run. This is a momentary mode and is the only way to run the immersion blender.

Yes it can most likely be fixed. Please see the solution for this problem that has already been covered here http://www.fixya.com/support/t3875766-braun_multimix_280_will_only_operate

You will need a soldering iron and some basic electronics skills to do this repair.

Regards
Toolpower

Hi.
This problem has been covered already on this link. Please leave a comment if further assistance is required and I will do my best.

Hi
The blender does not attach to any of the two holes for the whisks.
You need to push back the sliding cover in the center, bottom part between and behind where the whiskers attach. This will uncover a third attachment possibility, where you insert the blender and twist it a quarter turn into place.

Apparently the switch is very easily available, unknown for what reason. In Europe they say it is not available at all anymore, which I find strange.
However!
Dissasemble, by removeing base plate and screw underneath curved retainer plstic clip in the front. Then gently pry apart with blunt, thin object to split the two halves. Remember to unplug the power cord first. Check the circuit board for cracks, or burnt components. Then suspect the triac/tyristor. Desolder it and test it with a multimeter. (google "test triac multimeter"). Then note the code on the front of the triac, and search for a supplier of electronic parts to get hold of a new one and solder it back on. Note the orientation of the pins, and reattach heatsink if fitted. (Euro version have non.)The triac often looks like a flat design transistor and have a code/part nr that may look like; TCI 226 N, as on my European 230v version. Electronic components suppliers also have interchangeability lists for different manufacturers and use cross reference lists. Should only costs a few dollars or so. Triacs tend to stay fully open when failed, causing full speed in any mode. It is worth a shot.

See
http://www.smallappliance.com/product.asp?pid=5623&cur=USD&sid=18956&mid=5&gid=18978&prdCls=P&PartsPaNu=1&shopBy=Brand
(2 pages)

And you will find spare parts online for your braun which i believe is model nr 4642 (se baseplate).

You may also use braun's own spare parts finder at:
http://www.service.braun.com/product/product.asp?rg=NA&c=US&l=GB&typ=pf&frmTyp=s&grp=0&s=4642&subgrp=&des=&sgrp=s&sString=4642'HH'HH06'H'MultiMix&seite=2

But you will have to contact one of the authorised service partners to buy.

Most likely, you will have to replave the triac on the switch circuit board. If you are able to use a soldering iron and can order a replacement triac from an electronics outlet, se the description on this problem here:

http://www.smallappliance.com/product.asp?cur=USD&sid=18954&gid=18978&mid=5&pid=5623&prdCls=P&shopBy=Brand

See page 2 i think.

The problem is covered on this link

See
http://www.smallappliance.com/product.asp?pid=5623&cur=USD&sid=18956&mid=5&gid=18978&prdCls=P&PartsPaNu=1&shopBy=Brand
(2 pages)

And you will find spare parts online for your braun which i believe is model nr 4642 (se baseplate).

For a chopper attachment; you may need bowl plus rotating blade.

You may also use braun's own spare parts finder at:
http://www.service.braun.com/product/product.asp?rg=NA&c=US&l=GB&typ=pf&frmTyp=s&grp=0&s=4642&subgrp=&des=&sgrp=s&sString=4642'HH'HH06'H'MultiMix&seite=2

But you will have to contact one of the authorised service partners to buy.

Please see solution at this link on Fixya

The problem is covered here

1. remove the base palte by lifting the end opposite to the electric cord.
2. Loosen the bottom power outled slider, without removing it fully
3. unclip the curved plastic retainer in the front and unscrew philips head screw.
4. Work around the edges of the two halves until it comes apart and you are able to free the slider from its return spring.

And see pictures here at the bottom

See
http://www.smallappliance.com/product.asp?pid=5623&cur=USD&sid=18956&mid=5&gid=18978&prdCls=P&PartsPaNu=1&shopBy=Brand
(2 pages)

And you will find spare parts online for your braun which i believe is model nr 4642 (se baseplate).

You may also use braun's own spare parts finder at:
http://www.service.braun.com/product/product.asp?rg=NA&c=US&l=GB&typ=pf&frmTyp=s&grp=0&s=4642&subgrp=&des=&sgrp=s&sString=4642'HH'HH06'H'MultiMix&seite=2

But you will have to contact one of the authorised service partners to buy.