Husqvarna , No.455 Rancher, 20" Gas - Powered Chainsaw - Answered Questions & Fixed issues
Husky 268 will not start
There is a number of things an engine needs to run,clean fuel getting to the engine, a good spark, adequate compression and an air tight engine, if there is an issue with any of these the engine will struggle to run, so remove the muffler and take a look at the condition of the piston face through the open port, any sign of scuffing and the cylinder will need to be removed and the damage assessed, check there is a spark at the plug by removing the plug and resting against the cylinder, crank the engine to check for a spark, does the plug get wet with fuel after attempting to start, if not we have fuel starvation, possibly stale fuel, blocked fuel filter, broken fuel hose, a pressure test of the engine is more a shop check.
1/31/2022 9:19:41 AM •
Husqvarna ,...
•
Answered
on Jan 31, 2022
•
273 views
No compression release on older rancher 55
I have a very low time Rancher 55. It is hard to start when it sits for over two months. It is easy to pull with the spark plug out. The solution for me was to dribble 2-cycle oil into the cylinder and pull it about 7 times with the plug out. When I put the plug back in, it starts easily
2/7/2021 7:54:58 PM •
Husqvarna ,...
•
Answered
on Feb 07, 2021
•
1,131 views
I got the cover off,got the clutch unscrewed,then
what are you working on dude ? you failed to tell us the make, model and item you have removed the clutch from, then replaced........ likely - either it didn't work before you started, or it is now defective due to your inadequate attempt to fix it..... suggest - get a competent repairman to look it over and fix it.
3/8/2018 1:58:44 PM •
Husqvarna ,...
•
Answered
on Mar 08, 2018
•
62 views
I've got a 55 Rancher
You need certain things to be correct for the engine to run, clean fuel getting to the cylinder, a spark ( occurring at the correct time ) and the machine to be mechanically sound.
So remove the spark plug, is it wet? if not remove the hose and filter from inside the fuel tank, remove the filter and replace, if the plug is wet, then place the plug against the cylinder ( away from the open plug hole ) crank the engine, is there a spark? if not replace the ignition unit, if there is a spark, remove the muffler and check the condition of the piston face through the open port, any signs of scuffing or melting the saw has seized and will require stripping to assess the condition.
2/24/2018 9:46:18 PM •
Husqvarna ,...
•
Answered
on Feb 24, 2018
•
1,284 views
Husky Rancher 455 is not delivering enough oil to
a few of things here, the pick up pipe can get kinked thus slowing the oil flow down, the filter on the end of the pick up pipe may be partly blocked,if you are using non fling oil and the outside temperature is very cold you may need to thin the oil to allow a better flow, finally you can modify the pump shaft, this is done by increasing the angle on the end of the pump piston ( the bigger the angle the bigger the throw of the shaft and the more oil is pumped ) this is a final resort and has to be done with care, you have to remove the shaft from the pump body and hold against a grind stone to increase the angle
1/7/2018 7:17:37 PM •
Husqvarna ,...
•
Answered
on Jan 07, 2018
•
1,226 views
Connecting carburetor to the throttle on husqvarna 44 chainsaw
The wire linkage has a short Z bend in one end this hooks into the throttle lever from the outside, the other end has a long loop this goes into the trigger arm from the outside, you will need to twist the top of the trigger arm slightly to allow the linkage to go into the hole in the trigger arm.
12/29/2017 4:48:50 PM •
Husqvarna ,...
•
Answered
on Dec 29, 2017
•
2,479 views
Hi, I have an Husqvarna
Go to partstree.com type in model no then go to crankcase and you will see fuel tank vent and location
on diagram. Be sure to check your fuel line in tank to make sure it is not broken.
10/28/2017 7:57:14 PM •
Husqvarna ,...
•
Answered
on Oct 28, 2017
•
366 views
Husqvarna 455 rancher, chain getting too loose to
indicates incorrect length chain in use
the adjustment slots should be about 1/3 when fitted moving close to 1/2 when adjusted
the correct adjustment is when the chain in the center of the bar is lifted up the bottom segments of the chain are still in the bar groove
make sure that the oiler hole is not blocked from saw dust and chips
8/8/2017 6:32:20 AM •
Husqvarna ,...
•
Answered
on Aug 08, 2017
•
700 views
Pawls don't catch on rancher 455
The starter pawls are held on with small springs. If the springs are broken or installed incorrectly, this can happen. I would suggest replacing the springs and maybe the pawls. Check the recoil assembly to make sure the issue is not with the recoil assembly.
2/3/2016 8:54:15 PM •
Husqvarna ,...
•
Answered
on Feb 03, 2016
•
510 views
Husky boggs down
Make sure your fuel is good, fresh and properly mixed. Airfilter clean and correct resistor plug.
2/3/2016 6:51:23 PM •
Husqvarna ,...
•
Answered
on Feb 03, 2016
•
57 views
How to check the ignition coil?
To properly check the coil takes an expensive machine. Coils have a very low failure rate. However, if you doubt the coil, they are not terribly expensive. If you swap the coil make sure to properly set the air gap (distance from the fly wheel) and clean the area the coil mounts. Failure to get a good ground at the mounting location will prevent the coil from performing properly.
2/3/2016 6:24:05 PM •
Husqvarna ,...
•
Answered
on Feb 03, 2016
•
306 views
Gas in oil
This can only happen if the seal between the two case halves is damaged. This is not an easy fix. The saw will need to be completely disassembled to access the gasket.
1/15/2016 4:53:59 PM •
Husqvarna ,...
•
Answered
on Jan 15, 2016
•
96 views
How is the trigger installed?
The Husky website might provide an exploded view for buying parts. That should help.OR try Here http://www.ereplacementparts.com/husqvarna-chainsaw-parts-c-114486_114487.html
11/12/2015 9:03:27 PM •
Husqvarna ,...
•
Answered
on Nov 12, 2015
•
118 views
Not finding what you are looking for?