20 Most Recent
Black & Decker 9072CTN 2.4V Cordless Screwdriver - Page 4 Questions & Answers
I have tools and golf clubs in my garage and they
I don't know if you have been having higher then normal humidity where you live but one thing I have done for years that is inexpensive and easy is to wipe down your tools and golf clubs when not in use then spray them with WD-40.On my tools that hang in my shop I just spray them and leave the spray on. The tools that go in my tool boxes I spray and wipe lightly then put them on paper towel liners in drawers.I have my shop in a very old building with no heat unless I'm in it and have my stove burning so my tools are subject to extreme weather conditions. I do the same thing with power tool except being careful not to get any on the motors. I spray the table,blades and fence and mitre guide on my table saw and table,supportpole,gears and spindle on drill press and leave it on. It collect a bit more dust but cleans up easy.
The main ingredient in WD-40 is fish oil so it works great at displacing water and preventing rust. Thank you.
10/22/2016 11:14:41 PM •
Hand Tools
•
Answered
on Oct 22, 2016
How do I properly use a hand swaging tool for 3.2mm dia wire rope
they do make swagginhg tools that are fixed onto the yoke of a flaring kit. to hand swag, you should use the block of the flaring kit to hold your tubing. if you are swagging half inch tubing, hold the tubing up the diameter of the tube plus one eighth of an inch. tighten down the nut opposite the tube first then the closest one. this will keep the tubing from slipping.
Then hit it squarely with a hammer and it will bottom out at the flaring block. I would ease up on that last stroke to keep from cracking the tubing
3/1/2016 4:59:56 AM •
Hand Tools
•
Answered
on Mar 01, 2016
Electrnic hand growler to test
Go on E-bay for electrical test equipment and look for growler.or go google and type in armature growler test equipment and see what you get.
4/22/2015 10:51:36 AM •
Hand Tools
•
Answered
on Apr 22, 2015
Better Cables Should I buy them
They always try to sell you better cables but some are good while others are worthless when it comes to cables any type of Digital cable is fine, so HDMI, DVI, Digital Fiber Optic(also called TosLink) will work a $20 HDMI vs a $1000 HDMI will have no difference any anyone who tells you anything else either is trying to sell you a cable or does not know what they are talking about, now if you have equipment and the power cable is removable there is nothing wrong with investing in a nice heavy shielded power cable because the factory cables are shielded but I have seen the produce audio noise I can hear and video noise I can see, also any analog cables are fine to upgrade because good speaker cable is something I could hear the difference so always compare speakers cables to your inexpensive and if you can't hear a difference then return them, in the business we refer to the compare of 2 things as to A and B them. Surge suppressors are great because I much rather that my Panamax surge suppressor gives its life than any of my equipment but now surge suppressors also have Clean Power and what that does is take the small surgers the happen all day everyday out, that is why somebody gets home and they go to turn the TV on and it won't come on, well if you just have some cheap suppressor from Walmart etc the dirty power over time has destroyed the TV so yes clean power is a great thing, check out www.panamax.com for great products and www.soundadvice.com for everything cool as heck, they have everything you need for great sound. Remember if you can hear the difference then return it...
Back pack leaf blower wont run past half chick
Either your carb is still dirty as in has clogged jets or passages, bad diaphragm in the carb or you have the air/fuel needles way out of adjustment. Google what type of motor you have and how to set carb. Or even get a manual, that would be my advice. Also make sure you don't have to much 2 stoke oil in your fuel mix.
11/3/2014 8:34:36 PM •
Hand Tools
•
Answered
on Nov 03, 2014
How to put a raw plug into a plaster wall?
It's actually quite easy, but a few simple rules need to be followed. The drill size will depend on the size of the plug to be used. The type of drill bit will depend on whether it is a wall with plaster on it or plasterboard, which will have a cavity behind it. If it is a solid wall, use a masonry drill, on hammer setting if you have it. For a plasterboard wall a wood or HSS drill bit will do the job. Once you have drilled the hole, push plug in as far as you can, then tap it flush with a hammer. Job done.
10/19/2014 8:09:14 PM •
Hand Tools
•
Answered
on Oct 19, 2014
Edging a worktop
The best thing to use is contact cement or super 77 spray adhesive. Put either one on both surfaces, let dry, set it back on and use painters tape to hold on for 24 hrs.
7/25/2014 1:19:36 AM •
Hand Tools
•
Answered
on Jul 25, 2014
Not finding what you are looking for?
