LG WM2075C Washer - Answered Questions & Fixed issues

Most likely the cold water valve. Easy fix

you could try applying a bit of heat(not too much)it may come free but they can be a pig to remove

the bearings is in the center take of the center part all the way to the bearing dont need to dissemble the drum.

Hi from retired Englishman in SW France,
No promises but try this!
I would gently suggest as a first step that you clean the drain motor/pump lint tray/filter. So many 'faults' are caused by blocked filters and many machines will not even go to rinse or spin or release the door lock if there is any water still left inside.
Following are my complete and generic guidance notes for checking both the drain motor filter and the drain motor ;-0)
REMOVE POWER AND ENSURE YOU HAVE A WATER RECEPTACLE/RAGS TO SOAK UP THE WATER WHICH IS BOUND TO POUR OUT (alternatively use a wet vac as sensibly suggested by VinnyB1234!)
If you are unsure where the filter is, it is often behind the front lower (kick) panel (or in some machines at the rear in an awkward position!). These panels are either held on by (plasic) screws or will just pull off. Most filters are held in by a round cover/knob. Sometimes the filter will not come out with the cover and you will have to persuade it to come out to play.

It's surprising what people have found in theirs! It is always worthwhile checking it on a regular basis.
Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. Using something suitable like a glove see if it is easy to briefly slow the motor down. If it is easy then the motor is malfunctioning.

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C

Hi,

Here is a tip that I wrote about the LG OE Code and the causes and fixes...

Here also is the complete list of LG Codes

heatman101

You need 2 special tools to remove the clamps. Have you tried to shim the door latch so that it would close tighter? Have you cleaned the weep hole at the base of the gasket?

I have a manual HERE. If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

This dE error or fault code to indicate that the door is not latching properly. Check the lid or door operation to be sure it's not binding and that the door alignment is correct. Also, check the door/lid hinges to be sure they're not binding. Finally, make sure the door catch is in place and not broken. You may need to replace the door hook/catch or the door lock assembly.

its best to get an engineer to the problem as it could be anything at all or just an alignment problem eric

Sounds like the dial timer is defective, I am not affiliated with this site, https://www.repairclinic.com/Video

http://www.lg.com/au/support/support-product/lg-WT-H9556

https://electronicshelponline.blogspot.com/ http://homenol.blogspot.com/ Visit this site to get some details.

Remove the screws that attach the top panel at the back of the machine, slide the top backwards and remove the top panel. Run the machine as per normal, but be careful as the electrics will now be exposed, you will be able to see where the water is leaking from and be able to repair/replace defective part.

If you wish to get some details; check the site linked here. Pull up older posts........ http://electro-medical.blogspot.com/

take the back off see if the water pump making that noise or is broken should look something like this one

2 possible causes the water solenoid control valve is split in the diaphragm and not stopping the water the small hose from the base of the tub to the level control pressure unit is split or disconnected or the pressure unit has failed and is not activating the water control valve

Take out the soap drawer and clean the fabric softner compartment. This happens when there is residues left. And it gets clogged up.

The obvious question is how do you know that it is soap? What washing machine is it? The biggest problem with most washing machines is that people use too much soap to begin with. I would go to a store and get a new t-shirt or something. Run the machine with nothing in it. Then put the shirt in and run it again without adding any soap. When it is done check the shirt for soap. There could be a build up on the inside of the drum.

Please do not do another load of wash until this problem is fixed, or you may find yourself with a house/apartment fire! I am thinking your motor (most likely) or the controls (least) have a short, and are causing your problem. Oh, yes. Take a really good look at the circuit breaker box inside, because a broken or loose ground wire ( there are two) can also cause this problem. One ground wire should be white, one should be bare. Each should be securely screwed into the lugs of the grounded section of the circuit breaker box. God bless your efforts.

pull back the lip and look for a wire and spring that goes around the gasket. check out repair videos on repairclinic.com or appliancepartspros.com.

more often than not, this is a problem with a faulty heater in the machine not getting it up to temperatre (which help the powder dissolve). Put it on a 90 degree wash and keep checking the temperature, if it's not getting hot, then you need to swap out the heater. Ift IS getting hot, then it could be an empty pump problem. If the pump or waste pipe are blocked, the wash will take a very long time but it will be struggling to evacuate water and add fresh, which will also causse powder residue to be left behind. But I'd put my money on a heater fault