Top 20 eMachines T6534 PC Desktop - Page 3 Questions & Answers

0helpful
1answer

My emachine T2958 would not boot. the fans run but no bois nothing. i realise on the mother board alight is on by the letter F.Is it the motherboard ? help please

A good way to tell is disconnect your hard drive's, & CD/DVD ROM's power & data cable. Try to boot.If you get the same results then you can try & remove any PCI cards from the board, remove your ram stick. Try to boot. If you get an error beep because you are missing ram than this is good.Replace 1 ram stick back into your motherboard & try again. If it boots then you know the other stick is bad.If removing all the non-essentials from your motherboard doesn't work then all you have left are the motherboard & power supply. A simply power supply tester or spare power supply will tell you if it is your board or not.
7/16/2012 8:11:39 PM • eMachines T... • 182 views • 0 helpful votes
0helpful
1answer

System repeatedly reboots after cpu upgrade

Test all power and data leads that attach to your hard drive IDE,SATA the leads from your MOTHERBOARD TO YOUR HARD DRIVE make sure they have secure dust free connections and are not faulty or just replace them they could be faulty motherboard and a hard drive any leads between them will fail before your motherboard or your hard drive if its a flat ribbon 40 pin type IDE replace it this will be the first to fail

make sure all leads that are attached to your drives dvd\cd floppy have secure dust free connections and are not faulty or just replace them they could be faulty a computer needs

power and data to travel through every working device and to continue its cycle and have an end so any faulty leads will end up with a computer error

even something as small as a faulty power lead or fan lead can cause you problems

computers need all of the data and electrical current to travel through every working device and to have an end to be able work properly

make sure ram modules and cmos batteries have dust free secure seatings and cmos battery has charge some motherboards cmos batteries are soldered in

you might not have enough computer ram

not having enough computer ram will run your computer over its limits putting to much strain on the CPU central processing unit and can cause memory dumps

you might have to many programs trying to or accessing the internet at the same time scroll to bottom toolbar (bottom of screen) right click select task manager applications you will see whats running if you see anything you dont need running select end now and you might uninstall that specific program if you or computer does not require it to run and some unnecessary programs that could be jamming up your computer also under processes see what is ticking over in the background again if you see something you dont need to be and users you will see who is using your computer you might need to add more computer ram if you're not sure if a module is right for your system use the Crucial Memory Advisor tool for a list of guaranteed compatible modules. first you will need to select the manufacturer from a drop down list then select your product line from a drop down list then select the model then click find it will take you directly to compatible ram also you will have an option to scan your system you should always ask for a guarantee on the compatibility of the ram before making any purchase

might be getting hot

check you CPU make sure its securely seated and has thermal grease

http://www.hardwaresecrets.com/article/Thermal-Compound-Roundup-February-2012/1490

hope this helps

8/8/2012 9:46:23 PM • eMachines T... • 87 views • 0 helpful votes
3helpful
2answers

Modem is dead in t3985

contact you ISP internet service provider they should be able to supply you one free of charge depending on your current contract and if the modem is broken they will be able to check it online for youhope this helps
7/9/2012 2:31:52 AM • eMachines T... • 159 views • 3 helpful votes
0helpful
1answer

Where can I buy the Windows Vista Installation Cd? Thanks

HiYou will be able to purchase the CD from any computer shop near to your home.Also you can purchase it from the website of the Microsoft.Click Here in case you want to get more information.In case if you have any more trouble do contact back in Fixya.Thank you
8/11/2012 11:06:17 PM • eMachines T... • 36 views • 0 helpful votes
3helpful
1answer
0helpful
1answer

I need a driver for the floppy that came pre-installed on my emachine t1090

Get onlineand got to www.google.com In the google search box type: "eMachineSupport" or "Gateway" (without the quotes and put your manufacturer name before Support). Look for downloads and drivers. Enter your model number and operatingsystem when requested. Download and install the drivers.You can also try Driver Guidehttp://www.driverguide.com
5/6/2012 7:47:27 AM • eMachines T... • 44 views • 0 helpful votes
0helpful
1answer

Keep getting black screen with error message no bootable device - insert boot disk and press any key ... computer will start in safe mode if i'm quick enough with the f1 key ... HELP

Hello good day, just remove your SATA cable from your hard disk if your using a SATA type HARD DISK, change with a new one, or try to pull it back and put it back tightly. It's just a loss contact situation.That's why you are receiving that message.
3/14/2012 11:36:25 PM • eMachines T... • 100 views • 0 helpful votes
0helpful
1answer

Internal sound card quit working, need one to fix this

Check your sound card in the Device Manager Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/jason_77a19afa8d604dee
2/18/2012 7:46:35 AM • eMachines T... • 146 views • 0 helpful votes
0helpful
1answer

T6528

See http://www.manualowl.com/m/eMachines/T6528/Manual/119527 which is the manual for your eMachines T6528 system and has information on replacing hardware components including disk drives.
12/31/2011 3:04:47 PM • eMachines T... • 215 views • 0 helpful votes
1helpful
1answer

Emachines T6524 won't reboot after automatic update. I get the windows screen when I turn it on, and everything seems fine, then the screen goes black and I get the no signal message.

You should try to boot in safe mode without the card removed..If this got on after an update it is possible (almost sure) it messed up with your graphic card driver and now it needs to be reinstalled > To do so ..try to boot in safe mode...To do that press the key indicated on screen for boot menu and choose safe mode ...usually it is f8 key or f12 ..depend on the model .If it seams not to be able to find the safe mode boot ..try to stop the computer by unplugging it ..This will force it to stop improper way ..and will show the screen for safe mode and other ways to boot-up .select the first safe mode ..and let it start ..This mode will not load any drivers and work just with the minimum needed for to start .Go to control panel ...remove programs ..and remove the graphic card driver from the list ..after that if you have the disk insert it and run the driver again in original ..If you do not have it look for it on the manufacturer's site ..and download it ..If you need help with the driver ..let me know exact model of the computer ..and if it is not an on board card I need to know the exact model of the video card ..
12/30/2011 12:09:04 AM • eMachines T... • 214 views • 1 helpful votes
0helpful
1answer

T5224 THERMAL SHUTDOWN

test all leads that attach to your hard drive including electrical extensions SATA / IDE

the leads from your ((motherboard to your hard drive)) make sure they have a secure dust free connections and are not faulty or just replace them they could be faulty

make sure all leads that are attached to your drives dvd\cd have secure connections and are not faulty or just replace them they could be faulty

even something as small as an electrical extension or a faulty fan lead can cause you problems computer needs all of the data and power to travel through every working device and to have an end for a computer to be able work properly

a motherboard and a hard drive any leads between them will fail before your motherboard or your hard drive check all electrical extensions make sure they are securely seated even the cd/dvd drives need to have current go through make sure these devices are working

might be getting hot

check the CPU make sure it has thermal paste and dust free secure seating

also check your computer ram modules and cmos battery make sure they are dust free and securely seated some motherboards cmos batteries are soldered in

hope this helps

12/9/2011 3:55:02 PM • eMachines T... • 54 views • 0 helpful votes
0helpful
1answer

I recently did a dry erase on my computer but now I can't get any sound

dry erase??never heard of this expression before ,if its what i suspect that formatted the hard drive and re-installed the windows programme then yes you will need the original boot up disk to install the sound drivers .
12/2/2011 7:50:40 PM • eMachines T... • 57 views • 0 helpful votes
0helpful
1answer

I counted 13 quick beeps at startup on an emachines E520. what dose that mean ? how do i fix it please ?

Thirteen quick beeps at startup on an eMachines E520 usually indicate a problem with the laptop's RAM (Random Access Memory). This could mean that the RAM is not properly seated in its slot, or it could be a sign of a faulty RAM module.

Here are some troubleshooting steps you can try to resolve this issue:

Turn off the laptop and disconnect it from the power source.
Remove the battery from the laptop.
Locate the RAM compartment on the bottom of the laptop.
Check to make sure that the RAM module is seated properly in its slot. You may need to remove and reinsert the RAM module to ensure a proper connection.
Replace the battery and turn on the laptop.
If the problem persists, try removing the RAM module and testing it in a different laptop or using a different RAM module in the eMachines E520 to determine if the problem is with the RAM module itself or with the laptop's RAM slot.
If none of these steps solve the problem, it may be necessary to contact a computer technician for further assistance..
3/22/2023 7:58:30 PM • eMachines... • 40 views • 0 helpful votes
1helpful
1answer

How to factory reset a Emachines Etower 633id it boots up but says operating system not found it has Microsoft Windows ME Millennium Edititon (from Windows 2000 Professional)

  1. Boot the computer to the boot menu: To do this, restart the computer and press the appropriate key when prompted to enter the boot menu. On most eMachines computers, this is the "F12" key.
  2. Select the CD/DVD drive as the boot device: Use the arrow keys to select the CD/DVD drive and press the "Enter" key to boot from it.
  3. Insert the Windows ME boot disk: Insert the boot disk into the CD/DVD drive and restart the computer.
  4. Choose the "Start Computer with CD-ROM support" option: When prompted, choose the "Start Computer with CD-ROM support" option.
  5. Run the Windows ME setup program: The setup program should start automatically. Follow the on-screen instructions to install Windows ME.
  6. Format the hard drive: During the setup process, you will be prompted to format the hard drive. Choose the "Full" format option to erase all existing data and perform a complete factory reset.
  7. Install Windows ME: Continue to follow the on-screen instructions to complete the installation of Windows ME.
After the installation is complete, the computer should be in a factory reset state and you can begin setting it up as a new system. Please note that resetting your computer to the factory settings will erase all personal data and installed programs, so be sure to back up any important data before proceeding with the reset.
2/11/2023 3:21:00 AM • eMachines... • 62 views • 1 helpful votes
0helpful
2answers

I can't get my emachines 525 to start up all i get is operating system wasn't found so what do i do

Check the hdd is setup correctly and set as first boot device. Ensure there is no external drive/usb installed.
4/6/2022 4:46:41 PM • eMachines... • 57 views • 0 helpful votes
0helpful
2answers

I have a eMachines 525 when I start it up all I get is operating system not found

e525 lapTOP OR? FOR GOT TO TYPE THE "e"????? 2009 MADE? 13 YEARS AGO? 2 causes (of many but 2 are CLASSIC COIN cell is now dead CMOS and boot order lost. or hdd bad the cure is, new coin, and reset bios and set boot order to hdd0 first the hdd must pass smart tests. or all hope is gone foR IT. ask how. that error means boot order wrong or hdd is bad. boot fails missing on hdd is bad HDD 99% the time. NO COIN LASTED 13 YEARS. AND MOST HDD SAME THING. UNLESS PUT IN TIME CAPSULE IN Ln2, CRYRO FREEZED. now the BAD NEWS the COIN cell is soldered down to the MOBO and is not a normal CR2032 it is ML1220 rechargeable listed as 5 year life.(MAKER OF COIN) so you fOUND this PC in a garage sale dead for $1?>???? no history told at all, ever fix old cars. ? emaciates now owned by Acer and Toshiba does this nasty trick "solder down" e525 actual 525-undefined-undefined-0.jpg there it is, in all its glory, lots of screws to get and soldering pen to release it, I cut the wires up top and solder then new coin to top wires. and not touch mobo PADS that is a huge hint there.(do no harm)
4/6/2022 4:55:19 PM • eMachines... • 47 views • 0 helpful votes
0helpful
1answer

EMachines T5082 Desktop Help

old that is and UNDERSTATEMENT IF ever there was. 2009 made. moved. desktop PC large. 1: monitor cable video not put back as it was or pins bent sloppy movers 2: PC fans spin or not. CPU and PSU it not PC has no power. 3: power lamp on PC must glow steady not blink does it , if dead this ,there is no power to PSU. the monitor message only means video from PC is DEAD ! it does not know why only that is is dead.\ video signals is this a VGA cable end to end my PC has 2 VGA ports one on mobo and one on GPU card only the one on card works. unless I remove the card. Last guy on VISTA 32 bit on earth, yes? wow, brave./ ouch OEM lost the manual (retired, EOL sure) AC cord to PC loose at ether end not using AC power jack direct to wall AC? other SIGNS on PC no sounds from PC no fans spin PC beeps? Blinking LED? or 100% silent and one evidence of any life whatswever. PS makes all right sounds fans etc. but monitor set to wrong input port, via OSD. that is it for now. lots more causes. we need all symptoms to progress.
1/22/2022 2:20:16 PM • eMachines... • 59 views • 0 helpful votes
1helpful
1answer

I have an emachines ET1331G-03W with windows 7 pre installed. The motherboard (most likely the processor) decided to quit working. So I bought a wicked awesome gaming pc from a garage sale that didn't have a hard drive. I tried to swap my hard drive from my emachines to the new computer and it says there's no bootable drive. It doesn't matter what one of my 5 computers I put the hard drive in, it won't boot up. How can I get my data (pictures, music, etc) off of the hard drive, or how can i make it work in a new computer with all new hardware? I would prefer to keep using the same hard drive in a new computer if possible

microsoft has a license type called OEM which detects the computer that it is installed on and some computers have the licence key stored in the bios of the computer. So when you grab the old hard drive and put it in the next computer Windows will detect you changed computers and not run as per OEM licensing rules that it runs on only the original purchased computer. You might be able to run the drive as a secondary drive but you would need to install a new windows operating system and hard drive. And then use a partioning program to make the secondary drive not an active drive. also you new machine most likely has a different type of bios called EFI and you would have to change its settings to run AMI Bios but I do not think that is your problem as I think it is OEM but it might be worth investigating if you can run a legacy bios in the bios settings.
10/3/2019 9:13:01 PM • eMachines... • 134 views • 1 helpful votes
0helpful
1answer

How do you backup data on a eMachines etower 566 ir?

google that, the answer is near endless to 2nd hdd to external HDD to OOD CD_R, DVD-r , BD-r disks. burned ,using free imgburn.exe to any home server. to any USB stick memory to any web server on on earth paid admission you (off site is king) to the cloud. to high end TAPE systems. i keep mine on 3 of those places,.
7/15/2019 12:53:47 AM • eMachines... • 84 views • 0 helpful votes
0helpful
1answer

I turn my emachines EL1200-07w and it has black screen that says starting in safe mode but then just goes black and does nothing else.

hello and good morning. emachines are old and now owned by acer.com (gateway,etc) they OWN many old names. you are running XP right? the last man on earth to do so? XP is a virus magnet and doomed, it is time to upgrade. this PC is 2007 made. so is 12 years old, today.. the RTC coin cell battery will be no good now, replace it for $2 then reset BIOS inside BIOS screen " set default" then test the HDD, to be sure it is ok, if not? then reloading any OS of any kinds is not going to work with any bad HDD. Last, reload a new OS. there are the steps. and can be expensive, spent on any PC this old with zero street value. ($0 if broken a it is)
4/1/2019 11:10:54 AM • eMachines... • 89 views • 0 helpful votes
Not finding what you are looking for?
eMachines T6534 PC Desktop Logo

Popular Tags

33 questions posted

Ask a Question

Usually answered in minutes!

Top eMachines Computers & Internet Experts

Andrew Chrostek
Andrew Chrostek

Level 1 Expert

187 Answers

Cindy Wells

Level 3 Expert

6688 Answers

Brad Brown

Level 3 Expert

19187 Answers

Are you an eMachines Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

T eMachines

  • T eMachines

Most Popular Question

emachine troubleshooting

  • Computers & Internet
Loading...