Hobart H600 Stand Mixer - Answered Questions & Fixed issues
How old is my H660T mixer
this mixer came out of a pizza hut in illnois, looks like the manufacture date is june 1994, dont forget to vote, hope this helps, monomoy
10/18/2019 5:37:27 AM •
Hobart H600...
•
Answered
on Oct 18, 2019
•
718 views
How to change oil in 20 quart hobart mixer and the
on a a200 there is no oil. this mixer requiers grease. if mixer is leaking oil it is because the grease is broken down .you have to pull tpo cover off mixer remove trans. parts clean out old grease clean all trans. parts reassemble put top cover back on .then make sure mixer runs in all 3-speeds before putting 1.5 cans of -47grease back in grease can be bought @any hobart office
4/24/2019 5:56:16 AM •
Hobart H600...
•
Answered
on Apr 24, 2019
•
2,222 views
What is hobart h600, single phase or 3 phase?
Not sure if you are asking if an H600 is automatically a single phase or a 3 phase and the answer is NO. Depending on the motor it will be 1 phase or 3 phase application. It will have 4 wires versus 3 wires -- hope that makes sense 3 of the wires are "HOT" on a 3 phase and only 2 are "HOT" on a single phase Motor.
10/31/2015 10:19:54 PM •
Hobart H600...
•
Answered
on Oct 31, 2015
•
1,440 views
How much oil does my H 600 Mixer hold ( Hobart in the Transmission
1 gallon of 90w Gear Oil -- can be purchased from AUTOZONE! Make sure when you have completely drained from the large drain screw from under the mixer toward the back of where the attachments go on but not part of the part that spins around known as the Beater shaft! Once you have drained out all of the oil -- from the top where the front screw attaches the head or cap of the mixer -- add the oil there and make sure you are watching the sight glass to see when it is at the HALF way mark in other words when the oil level (TIP: Use a bright led flashlight to shine directly at this sight glass to view level) reaches to the midway mark of the oval sight glass, THEN STOP! It is full! Carefully start mixer on 1st gear and then 2nd so on and so forth to make sure everything is getting relubricated correctly and slowly -- don't just go setting it on 3rd or 4th speeds as you want to baby the mixer when you just put in new gear oil
Hope that helps!
7/22/2014 9:04:49 PM •
Hobart H600...
•
Answered
on Jul 22, 2014
•
2,681 views
Can you use a spiral dough hook when the mkixer
You can but the dough would ride down towards the bowl instead of up and your mix would not turn out properly.What kind of mixer do you have?i'm a hobart tech and repair these mixers often.Let me know.
5/2/2014 3:51:35 AM •
Hobart H600...
•
Answered
on May 02, 2014
•
303 views
Motor not spinning in hobart 60 qt mixer
Check manually after disconnecting the motor if this is jammed. If so the motor must be reset as the bearings are faulty and so the rotor seems to get stuck with the coil core.Also if there is high drain with heat it is possible that the coils are faulty and might need an insulation failure test.
2/24/2014 9:14:09 PM •
Hobart H600...
•
Answered
on Feb 24, 2014
•
746 views
I need a wiring diagram
You cannot wire a three phase motor for single phase and you cannot wire a single phase motor for three phase. If you have a three phase dual voltage motor your options are 220 or 440 volts. If you have a single phase dual voltage motor your options are 120 or 240 volts. A 208 volt Hobart motor will only function correctly on 208 volts and is not dual voltage.
2/18/2014 1:11:20 PM •
Hobart H600...
•
Answered
on Feb 18, 2014
•
2,828 views
My Hobart mixer is hard to start. I have to keep
take off the side cover where gear shifter is, you probably have the original arrow hart contactor in there ,that part is obsolete but you can get a kit from hobart to upgrade the control circuit
12/15/2012 3:53:21 AM •
Hobart H600...
•
Answered
on Dec 15, 2012
•
490 views
I have Hobart Mixer Model
The transmission has to be disassembled for this repair. I believe your best option is to contact your local Hobart office and have them do it.
9/13/2011 3:21:58 PM •
Hobart H600...
•
Answered
on Sep 13, 2011
•
1,159 views
HELO I recently purchase a
The machine can be internally rewired for 220 3 phase. Call your local Hobart office and have them come out and take care of it.
7/5/2015 3:08:13 AM •
Hobart H600...
•
Answered
on Jul 05, 2015
•
747 views
I needed to know the
Hello Jbabajanov,
I understand that you want to know about the HP (Horse Power) of a H600, 60 quart mixer and weither it is a single or three phase.
All H600 Hobart mixers are equiped with a 2 horse power motor.
As to wether it is single or three phase you will need to look at the service tag of the machine. If is listed on it weather it is single or three phase.
Thank you for choosing FixYa.com
Justin
5/13/2011 3:32:44 AM •
Hobart H600...
•
Answered
on May 13, 2011
•
389 views
Not finding what you are looking for?