Moen & Replacement Cartridge - Answered Questions & Fixed issues
We are trying to put the retaining clip back in
The Cartridge probably isn't in all the way. Pushing it in by hand doesn't always seat it properly.
Make sure the clear plastic is centered in the gap where you push the clip in, then a few gentle taps with the wrench, followed by pushing around the edges (the black part) with a flat-blade screwdriver gets it all the way in.
If the cartridge is aligned and seated right, the clip should slide right in. If you have to force it, the cartridge is not in right.
5/19/2022 2:09:40 AM •
Moen &...
•
Answered
on May 19, 2022
•
8,637 views
New MOEN 1222 cartridge leaks
remove it and carefully inspect it, you might have scuff'd up the rubber's on the cartridge when you inserted new one.clean out,look in hous'ing for any foriegn mat.etc .you may need another new cart.
4/17/2019 4:07:49 PM •
Moen &...
•
Answered
on Apr 17, 2019
•
6,237 views
Moen water flow restricted and only warm
Not sure about your particular valve, but most newer shower valves have an anti-scald limiter that stops the handle from turning too far to the hot water side. Check for a ring or a pin under the handle that can be set in different positions. It will need to be moved clockwise to allow the handle to rotate farther to hot.
Hope that helps. If you have trouble finding it, try looking up a diagram for the valve model.
7/9/2017 4:15:22 AM •
Moen &...
•
Answered
on Jul 09, 2017
•
4,481 views
How do I remove the old one
First you must determine if your shower faucet is posi-temp or if it has a separate balancing spool. The posi-temp takes a 1222 cartridge and the other type takes a 1225 cartridge. Remove the handle. There is a horse shoe clip which is removed from the top of the cartridge. A cartridge puller is highly reccomended. There are two different kinds. On the brass stem inside the cart. there is a notch. Make note of its position as this determines which side hot and cold are on. Pull the cartridge by twisting back and forth while pulling. Lubricate the inside of the cartridge barrel with faucet grease. No motor oil, vaseline or WD-40! They all eat rubber. Insert cart. and retainer clip. Install handle.
8/11/2014 10:05:18 PM •
Moen &...
•
Answered
on Aug 11, 2014
•
173 views
Installed a new faucet and no water comes out
Since your question is so vague (is it a shower, tub/shower, lavatory, kit. sink or laundry tub faucet) I'd have to say that the flow restrictor in the aerators or showerhead is clogged up. Just unscrew and remove and either clean aerator or sh.head out and/or remove flow restrictor permanently. If that doesn't work turn off water and disconnect supply tubes from faucet and run them into a bucket and turn water back on to check for volume. If you have plenty of water at supplies then remove faucet and take defective faucet back to where it was bought and get another one!
6/9/2014 6:52:57 AM •
Moen &...
•
Answered
on Jun 09, 2014
•
279 views
How do I remove the old cartridge
its not wanting to come out easy but after the retainer clip is removed don't be gentle it will come out good luck
6/8/2014 5:14:28 AM •
Moen &...
•
Answered
on Jun 08, 2014
•
116 views
Removing Moen Cartridge with BROKEN shaft
Alan, I'm a certified plumber for over 30 years specializing in service. I hate telling you this but what you have is a Moen posi-temp and there is no tricks or easy way to remove it other than a cartridge puller which won't help in your case since it's already broken. Just break out your drill and carefully have at it, BUT don't leave the water on it won't help and may be dangerous and/or ruin your drill. For some reason on all Moens cartridges the rubber grommet tend to adhere themselves to the brass valve body's. Sorry, wish I had better news...
9/17/2013 4:07:47 PM •
Moen &...
•
Answered
on Sep 17, 2013
•
5,539 views
Install ation and adjust moan 1225 cartrage
Moen cartidges are supposed to be guaranteed for life, so take the bad one back for a refund!! Once the handle is off there is a metal u clip that you pry up to take off. You'll probably need to purchase a Moen cartridge removal tool, because simply pulling on the cartridge stem often is not enough force to remove the old one. Look at the way the ears are positioned with the clip (prior to removal) and replace in the same position.
3/26/2013 2:47:29 AM •
Moen &...
•
Answered
on Mar 26, 2013
•
161 views
I have a single -handle
Should be coming out if head not stripped or threads inside at set screw aren't stripped. Can you tell at all with perhaps flashlight if set screw is turning at all? Look like it backing out?
11/14/2012 7:26:06 PM •
Moen &...
•
Answered
on Nov 14, 2012
•
3,707 views
Low hot water pressure in kitchen faucet
I have moen kitchen faucet # 7560 and water pressure very low. What should I do? We check water flow in pipe it is ok. I changed cartridge as well as pipe nothing help. Please let me know. thanks
6/10/2014 2:34:43 PM •
Moen &...
•
Answered
on Jun 10, 2014
•
1,522 views
Not finding what you are looking for?