20 Most Recent
Porcher VENETO II One-Piece Toilet - 97220-00-001 - White - Page 4 Questions & Answers
My porcher toilet wont flush....
Hello:
Please feel free to call Customer Service
1-800-359-3261
General Customer Service
Monday through Friday
8:00 A.M. to 7:30 P.M. EST
Technical Customer Service
Monday through Friday
8:00 A.M. to 6:00 P.M. EST
8:00 A.M. to 3:00 P.M. EST
Customer Care at Porcher
Porcher Customer Care
P.O. Box 6820
1 Centennial Plaza
Piscataway, NJ 08855-6820
All the Best,
Paul, -ASB
9/12/2011 12:03:30 PM •
Porcher Home
•
Answered
on Sep 12, 2011
Wc is starting to run
The float on the ballcock/ flush valve in the tank needs ajusted or rebuilt/replaced.
2/4/2011 8:21:18 PM •
Porcher Home
•
Answered
on Feb 04, 2011
Porcher 6.0 Lpf / 1.6 toilet. Plumber said he
Try replacing the flapper, they are cheap and so long as the tank and or bowl are not cracked you can replace all of the internal parts and basically have a brand new toilet much cheaper then replacing the entire unit. Go down to your local hardware store and everything you need is in one simple kit with very simple instructions. Good Luck.
7/22/2010 2:59:24 AM •
Porcher Home
•
Answered
on Jul 22, 2010
I have a Porcher toilet
Hi there,
Well you need a screwdriver remove the old nylon screws from the toilet bowl seat. Use a cloth to clean around the area as needed. Replace the old nylon bolts with the new metal bolts. Keeping all the pieces in order, put the metal oval shaped washer on the seat hinge. Next put the bolt through the washer and down through the back of the toilet seat. From underneath, place the old nylon tap, or a nylon washer, and the new metal tap to the bolt. Keeping pressure on the top of the bolt, use the pliers, or an open-end wrench to gently, tighten the taps. Carefully tighten the right tap, evenly with the left tap, to keep the seat level on the toilet bowl. note: Do not over tighten, to prevent cracking the porcelain.
Items needed: 5/16 x 2 ¼ inch Toilet Bowl Bolt Set.....
Please post comments for more help or information.......
Good Luck!!
Thanks
2/13/2010 12:17:05 AM •
Porcher Home
•
Answered
on Feb 13, 2010
The temperature dial just keeps turning around and
If the knob is just rounded out, you can probably replace it with a new knob from the hardware store. If the shaft of the valve is stripped and not the knob, someone will need to replace the valve's innards. If the knob is fine but the valve is not working, again the innards need to be changed. You can get a kit to do it yourself but it's kinda tricky.
11/25/2009 4:39:42 AM •
Porcher Home
•
Answered
on Nov 25, 2009
What is a meat tenderizer?
This is used to tenderize meat before you cook it. It makes the meat easier to chew and digest. You can also use it before you boil or fry meat. You can do this mechanically, with something like a meat mallet that cuts up the meat fibres. You can do it thermally by putting the temperature really high to break down the connective tissue of the meat. The last method is enzymatic and uses enzymes to break down the collagen. This method is either slow with dry-aging the meat or you can use fruit to marinate the meat.
4/16/2024 6:28:01 AM •
Home
•
Answered
on Apr 16, 2024
Lost half of my jets on one side of the tub only.I have tried closing the jets that do work half,does not make a difference to the jets not working.Would it be best to empty the tub and start over?
it's likely due to an air lock. Here's what you can do to resolve this issue:
Manually Clearing an Airlock:
Run the jets on low for about 30 seconds.
Then run the jets on high for another 30 seconds.
Repeat this process 3 or 4 times.
If you hear a gurgling sound and see air bubbling up, continue running your hot tub until it pushes all the air out.
If this doesn't work after several attempts, try a different approach.
Bleeder Valves or Pump Method:
Some spas have bleeder valves that allow you to bleed air out of the lines.
First, turn off the spa at the breaker.
Access the pump and loosen the valve to allow the air to escape.
When the air has bled out (you'll notice it turns from hissing air to a stream of water), close the valve.
Run the pump to ensure the jets are now pumping water as expected.
Why Are the Jets Not Working on One Side Only?:
Many hot tubs have two water pumps.
If the jets on only one side of your hot tub stop working, there could be an airlock in only one of the pumps.
It could also be a blockage in the jet lines for that side or a problem with the internal mechanism of the jet itself.
Can You Use a Spa with an Airlock?:
It is not recommended to use a hot tub with an airlock.
4/3/2024 4:33:08 AM •
Home
•
Answered
on Apr 03, 2024
Restarting my marcel hour strike quartz clock nrms603.
To restart your Marcel Hour Strike Quartz Clock NRMS603, follow these steps:
Stop the Pendulum: Gently stop the pendulum from swinging by holding it still.
Remove the Battery: Open the clock case and locate the battery compartment. Remove the existing battery.
Wait for a Minute: Leave the clock without a battery for about a minute to allow any residual charge to dissipate.
Insert a New Battery: Insert a fresh battery into the compartment, ensuring the correct polarity (usually marked on the battery holder).
Start the Pendulum: Gently release the pendulum and let it start swinging.
Set the Time: Use the clock's time-setting knob or buttons to adjust the time to the correct hour and minute.
Your clock should now be restarted and keeping time accurately
4/3/2024 4:30:05 AM •
Home
•
Answered
on Apr 03, 2024
Not finding what you are looking for?