American Standard 738651-0070A Champion Toilet Flush Valve Seal - Page 2 - Answered Questions & Fixed issues

have the valve seat rubber replaced

Run a short snake thru the line. Somewhere between the drain and the tee into the line with the sink is a clog.

Be sure to pull the plunger all the way up when diverting the water between the the tub and shower if ti keeps giving you a problem it's faulty

depress and release button and whirlpool will stop

It's possible you installed the valve upside down, all values should be labeled in some way marking either hot and cold or it will say the word up where the riser tube port for the shower head is. If that's not the case remove the tub spout and check for any obstruction sometimes during tile or constructing debris can get into the pipe for your tub spout. Lastly the diverter on the tub spout could be bad. Try a new tub spout

Trey, motor or pump is seized, have tech. take a look and repair.

1. Turn off the water at the shutoff valve, flush the toilet and hold down the handle. There may be a little water left in the bottom of the tank, but don't worry about it. Wipe the flapper seat with a clean cloth to make sure it's free of debris, and check it for cracks or splits (Image 1).

   How to Fix a Leaking Toilet ' how-tos ' DIY

   www.diynetwork.com/how-to/.../how-to-fix-a-leaking-toilet DIY Network
   Feedback

How to Fix a Leaky or Runny Toilet - This Old House

www.thisoldhouse.com > ... > Toilets
This Old HouseA toilet that leaks or runs is an easy homeowner fix-if you know how to diagnose the trouble. ID parts and problems with this handy guide, and hit the hardware ...

page tite

General Plumbing Supply has always come through for me... Yelp only gives them a 3/5 but I have always had to wait with PROFESSIONALS to get my turn. I'm not big on ambiance when hunting for obscure plumbing parts.. BRING your old (always... any-parts) seat with you! Amazon says $34 (plus tax)... Phenomenal return policy A quick search on line yielded lots of other choices... Happy hunting!

Change the flap in the flush container.

The new toilet has more flushing volume than the old one. The system should handle this. The problem could be the vents on the roof are plugged or something in the line is obstructing the flow. You will need to contact a plumber

This is called air hammer, most times this is caused by vibration when a water pipe is too close to a support board you can put in a hammer arrester or make sure pipes are away from support board .

This can answer only by checking the system. Call another plumber.

Yellowing is a sign of age, but plastic items can be brightened up a bit. Here are some suggestions: http://www.howtocleanstuff.net/how-to-whiten-yellowed-plastic/

Is the tank cracked or is it leaking from the bolts that go through the bottom? If the bolts are leaking shut the water off, Should have a shut off valve behind the toilet, If not possible around your house. Mine is out by the road where the water meter guy can check it. But shut the water off and put 2 new bolts and gaskets through the toilet. Very cheap fix. under $4.00 USD

Your vent stack may be clogged. The pipe that goes up to the roof. Let's air into sewer pipes when you flush. A birds nest or something can do it.

Check to make sure the chain fromanagement the trip lever to the flapper does not have too much slack in it if there is shorten the chain so when the lever is down there is just a little slack in the chain. Hope this helps Bob

The problem may be the flapper that seals between the tank and bowl is leaking or the overflow pipe may have a crack in it. I wouled replace the flapper first and check the overflow pipe for cracks. Hope this helps. Bob

Hello their is a product called Plasweld,it comes in a handy tube, Carefully scratch along the crack to allow the weld to come flush with the surface of the shower tray,MUST BE PERFECTLY DRY! squeeze into the crack and it will find its own level ,this produce actually welds the plastic together Good builders merchants should stock this item.GOOD LUCK

Adjust the float so water level stops at 1/2" below top of overflow pipe.