20 Most Recent
Maax Calla 6042 Bathtub - 101058-000 - Page 8 Questions & Answers
I have a Maax Tigress shower. This will be 3rd
If the GE Silicone was used first then this may be the cause. For some reason the GE formulation does not adhere very well to new plastic/acrylic, however it does very well on most other surfaces. The mono brand is better for plastics/acrylic. If all of the GE silicone was not removed before the mono was applied then the mono formulation would not stick very well to the GE silicone that was not entirely removed. Unfortunately there is no easy way to do this other than with a plastic scraper tool and lots of elbow grease. Rubbing alchohol can be used to soften the silicone slightly and will not damage the acrylic, aluminum or glass. If the mono was applied first then the flexing will be the problem. The only solution to a flexing problem is to remove the shower unit and reinstall the unit in either a morter or sand base to provide more support for the shower unit. If you use a morter base ensure there is a vapour barrier installed between the morter and the shower unit as the chemicals/minerals in the morter will degrade the shower base over time. The downside to morter is that it will not flex and may cause cracking over time if and when the house shifts. A sand base will shift with the house.
8/21/2010 10:59:32 PM •
Maax Home
•
Answered
on Aug 21, 2010
It is passible too have
Hi there,
Well you may please follow the link below to get your manual -
http://www.datamanuals.com/catalog/index.php?cPath=46_63
Good Luck!!
Thanks
8/5/2010 1:30:27 AM •
Maax Home
•
Answered
on Aug 05, 2010
I can't get all the jets to work
Most likely your jets are clogged. Usually you can remove the jet where it mates with the tub and see what's going on in there. Also, you might want to open your access hatch and see if you can get to your non jetting jets this way. Hope this helps.
7/27/2010 5:08:52 AM •
Maax Home
•
Answered
on Jul 27, 2010
Bought a used maax hydrotherapy airotherapyand
Start with the simple things first. Remove the bulbs for the chromotherapy lights and look for any corrosion that may be inhibiting the lights from working. It sounds like you may have purchased a tub that needs a refit or overhaul. Your best bet is to spend the money and hire a licensed electrician to examine the unit. It's best to be on the safe side when dealing with water and electricity. For safety the tub should be on its own ground fault interrupted circuit. GFIC.
7/17/2010 12:41:04 AM •
Maax Home
•
Answered
on Jul 17, 2010
Bathtub installation
Now I see the wood stud is added support and the tub should rest on it. though it is not to hold the tub up. Like a man using a cane the cane doesn't keep a man standing by itself. Rather it helps a person be more stable that's what the stud does. Set at height for a level tub.
Here is a trick as well for supporting the back of the tub (Shimming) Get some of the expandable foam. Set everything in place like the wood ledge when you have everything in place and tub pre-fitted. Remove tub and place a line of foam along back side. Place tub in place and when foam expands and dries it will become your perfect shim. Hope this helps, thanks for using FIXYA. Good luck, Jeff
4/8/2010 5:54:50 PM •
Maax Home
•
Answered
on Apr 08, 2010
Have a small ding in tub. Where can I find
Easiest fix is to buy appliance touch up paint. Looks like a fingernail polish bottle. They'll have your shade. H/Depot, Lowe's, similar should carry.
Best regards, --W/D--
7/24/2009 2:59:57 PM •
Maax Home
•
Answered
on Jul 24, 2009
Find board for maax bubble-tub
You will probably have to go to the manufacture website to find a dealer in your area that you can purchase one from. Also, you can check online as well for specific parts for your tub. If often just google the brand and model number and start clicking on links to find what I want or need. Good luck to you!
3/23/2009 3:30:15 AM •
Maax Home
•
Answered
on Mar 23, 2009
Maax velvet bubble-tub does not work
This will tell you that the control board is bad. You will need to replace it. But before you do, make sure that the switch is telling the board to send the signal. Check to see if the board is getting the power required and that the poser is leaving the board.
3/22/2009 4:12:50 PM •
Maax Home
•
Answered
on Mar 22, 2009
What is a meat tenderizer?
This is used to tenderize meat before you cook it. It makes the meat easier to chew and digest. You can also use it before you boil or fry meat. You can do this mechanically, with something like a meat mallet that cuts up the meat fibres. You can do it thermally by putting the temperature really high to break down the connective tissue of the meat. The last method is enzymatic and uses enzymes to break down the collagen. This method is either slow with dry-aging the meat or you can use fruit to marinate the meat.
4/16/2024 6:28:01 AM •
Home
•
Answered
3 days ago
Lost half of my jets on one side of the tub only.I have tried closing the jets that do work half,does not make a difference to the jets not working.Would it be best to empty the tub and start over?
it's likely due to an air lock. Here's what you can do to resolve this issue:
Manually Clearing an Airlock:
Run the jets on low for about 30 seconds.
Then run the jets on high for another 30 seconds.
Repeat this process 3 or 4 times.
If you hear a gurgling sound and see air bubbling up, continue running your hot tub until it pushes all the air out.
If this doesn't work after several attempts, try a different approach.
Bleeder Valves or Pump Method:
Some spas have bleeder valves that allow you to bleed air out of the lines.
First, turn off the spa at the breaker.
Access the pump and loosen the valve to allow the air to escape.
When the air has bled out (you'll notice it turns from hissing air to a stream of water), close the valve.
Run the pump to ensure the jets are now pumping water as expected.
Why Are the Jets Not Working on One Side Only?:
Many hot tubs have two water pumps.
If the jets on only one side of your hot tub stop working, there could be an airlock in only one of the pumps.
It could also be a blockage in the jet lines for that side or a problem with the internal mechanism of the jet itself.
Can You Use a Spa with an Airlock?:
It is not recommended to use a hot tub with an airlock.
4/3/2024 4:33:08 AM •
Home
•
Answered
on Apr 03, 2024
Restarting my marcel hour strike quartz clock nrms603.
To restart your Marcel Hour Strike Quartz Clock NRMS603, follow these steps:
Stop the Pendulum: Gently stop the pendulum from swinging by holding it still.
Remove the Battery: Open the clock case and locate the battery compartment. Remove the existing battery.
Wait for a Minute: Leave the clock without a battery for about a minute to allow any residual charge to dissipate.
Insert a New Battery: Insert a fresh battery into the compartment, ensuring the correct polarity (usually marked on the battery holder).
Start the Pendulum: Gently release the pendulum and let it start swinging.
Set the Time: Use the clock's time-setting knob or buttons to adjust the time to the correct hour and minute.
Your clock should now be restarted and keeping time accurately
4/3/2024 4:30:05 AM •
Home
•
Answered
on Apr 03, 2024
Not finding what you are looking for?