Top 20 American Standard 2083.102 Standard Collection Bathtub, Right hand outlet Questions & Answers

Here is a link to some PRODUCTS from our site at US Parts Center that we use to clean the bacteria from the water lines and to prevent it from coming back again.RodUS Parts Center888-521-6183

They are bad about leaking,you prob. need to replace the cartridge with new one. the seals in them get dry and shrink of they have been sitting in the box for a long time on the shelf or in a warehouse. you never know how long ago they were built and just sitting.

They do not all leak. The problem may be that your faucet is simply wearing out and is due to be replaced in total. Try putting some plumbers grease on the cartridge and the chamber.....not too much..........that may do the trick for u.

The diverter in the main body of the faucet is sticking. I have included a link to all the kitchen faucets. You will have to determine which one you have but they pretty much use the same housings and guts for each of their single handle faucets. You might have to do a little research on your end so you can find info on how to replace the diverter. It's usually not hard to do.

the handles themselves are not the problem but if you remove the handles then there are usually nuts behind them to pull out the valve out of the body. most tub faucets use either orings or rubber washers to seal it. without knowing exact brand and model is hard to tell you exactly what you are dealing with. some brands sell the whole valve to just swap out and some you have to go match up the orings or washers.

These tubs often have an adjutment on them that control how hard the jet blows. You may have to adjust them. There isn't anything that can get into the lines that will clog them so I can't think of anything else it could be.

You have a limit switch that is tripping. I bet it is the flame roll out switch that is very close to the burners. You can bypass this switch to check if it is the one causing the problem by removing the two wires going to it and installing a small jumper wire between them. If the unit starts up, then that's the problem and if not, check all of them. But that's pretty much the only thing it can be. But, you need to double check that the unit is being told to come on and not cutting out intermittently. I doubt it though!

Try denatured alcohol I’m happy to assist further over the phone at https://www.6ya.com/expert/robert_aad3edb7dfa380b9

If it's a zoned system, make sure that the damper has opened fully or is operating at all. If it's not, see if some ductwork is being pinched off or has come loose or torn loose by critters. You also want to check the filters as well.

Is this in the basement and if yes then you have a brake in the pipe some where because you say that your snake is stopped by cement.

This could be caused by a faulty relay or switch in the control panel. It is best to have a qualified technician inspect the control panel and replace any faulty components. If the issue persists after replacing the faulty components, then it could be a wiring issue and a qualified electrician should be consulted.

To make the water level higher in the pan, the outlet pipe must be higher.

Adjust the float on the fill valve

Depends how old your toilet is, it may be a calcium build up problem on your little inlet pipe inside your tank, but first check your water shut off valve on left side of your toilet near the wall....It may not be open all the way OR the valve has an issue...

Hi, First, carefully remove your tank lid, and place it where it won't break or fall. Look for a four-digit number located on the back of the tank, near the water level mark. This is your tank model number. If the number starts with a two, it is a one-piece toilet. Then....visit this link: https://www.americanstandard-us.com/parts-support/faqs/toilets Good Luck!

these are called phantom flushes. the water is slowly leaking around flapper or the is a scratch of the flapper seat. I use fluidmaster parts

Toilets wear out from mineral deposits. Fixn may cost more then new. Googl used commodes first

water level to low or drain partial clog

More likely the sensor has malfunctioned.

air bound or pump overheating