Top 20
Sharp R-1505 Microwave Oven Questions & Answers
Why would the turntable stop turning and the unit stop heating?
hi,
there is a micro switch that signals when the door is closed. this tells the machine that it's okay to start the turntable and heating process.. if the micro switch breaks or shorts out then the switch does not send the signal so the machine does not work.
hank
Heat: I placed a microwavable food product in my
Maybe. The presence of metallic material (foil, stainless steel silverware, etc.) in an operating microwave oven creates electric arcs between the foil and the inside wall of the oven. And this can destroy the electric components.
My Sharp R1505 Microwave's LED display is
You can order a new control unit (part number CPWBFB075MRU0 which comes with a display) from
Encompass here.
Or you can get yours repaired for $39.95. Details here.
We're happy to help you with free
advice and we'd appreciate your thoughtful rating of our answer.
I have a Sharp R-1505
Hi,
Here is a tip that will help you to figure out what is wrong with your Microwave Oven....
Basic Microwave Oven Troubleshooting Tips
heatman101
-\\\\\\\\\\\\\\\\\\\\\
Sharp r-1505 microwave. several segments in
Sharp had "issues" with that board (connector cable fail). That was back in 2002. Give them a call and see if they will send you a new control board (part # CPWBF070MRU0) All of the 0's are zeros.
If not, look at that ribbon connector where it's kinked, and you'll see a spot that should be repaired, ie broken wire.
Good luck with the phone call. Refer them to bulletin # MW-166.
fil
Looking for sharp r1505 turn table motor
The service manual is
here for your convenience.
The original part number was RMOTDA211WRE0, but that was been subbed by part number RMOTDA264WRZZ, which was finally subbed by the current part number RMOTDA252WRZZ. (Please note the difference between ohs "Os" and zeros "0s").
Part number RMOTDA252WRZZ is in stock at
Encompass here or you can call them toll-free at 866-779-5835.
We're
happy to help you with free advice and we'd appreciate your thoughtful
rating of our answer.
Digital read out quit working
We'd be happy to help you with free assistance - including part numbers,
part sources, and service info - if you'll post a new help request to
FixYa including the following:
- brand
- full model number
- detailed symptoms
The light bulbs ("oven light"
If your
waveguide cover
is damaged, it will need to be replaced.
It provides critical
protection for the magnetron and waveguide.The inside light (unlike the cooktop lights) is not meant to be user replaceable.
You have to remove the oven from the wall, remove the outside cover, then you'll see the lamp on the right side of the oven in its socket on the air duct near the magnetron.
The installation instructions make this much easier. If you don't still have yours, we have those form a similar model
here to help you. I hope they're close enough.
We have
the service / repair manual for this model and have uploaded
it to our
site here for free download to help you.
You can order Sharp parts from the
Sears Parts Direct
Web site
or from
Encompass here.
We're happy to help you with free
advice and we'd appreciate your thoughtful rating of our answer.
How do I clean the inside of the microwave? It is
DO NOT use SOS pads! They are made of STEEL WOOL and will remove the protective finish inside the oven cavity. Without the protective coating, the microwave can arc internally and ruin the magnetron. Use the green scrub pads you find in the dish detergent section of your local grocery store. They are considered non-abrasive. Use the green scrub pads along with a non-abrasive cleaner such as Soft-Scrub or 409. Wipe clean with a fresh water and dry with a clean cloth.
Not finding what you are looking for?