20 Most Recent Moen 4621 Chateau 1 Handle Bathroom Faucet W/drain Assy - Page 6 Questions & Answers

Go underneath and push it up from below.

If you didn't open the faucet to relieve the pressure, the cartridge is pushing up against the clip. Making sure that the valves under the kitchen sink are closed, and open the faucet to relieve the pressure. There is usually a hole at the end of the clip which you can stick an awl into to help removal. Good luck! P.S. Make sure to note which side of the brass spindle has the notch on it. It should be either facing you, or it should face away. If you put it in wrong, you will reverse the hot and cold. If this happens, simply remove the handle and rotate the spindle 180 degrees to reverse it back.

not from fixya site try a plumbers shop

Sorry can't help with this type of inquiry except to say I would contact Moen customer service by phone or email.

If brand new take it back and have it replaced.

There car certain modern techniques to keep your house clean, especially roof cleaning, roof coating, roof coloring, moss removals and coating plays a vital role in keeping your house neat.

The only ones I've seen that are recessed come with a tool, same diameter as aerator with gear like teeth on it. The teeth match up with the teeth on aerator and you just simply unscrew it. If you don't have the tool I have used a pair of needle nose pliers instead. Point pliers straight up, one point on each side of the aerator slid in between the teeth then turn the pliers (counterclockwise)

when answered you get a notification

No they do not unfortunately

You can always by a new one. I suggest a different brand. I use Price Pfister.

well it can only be 1 of 3 things, 1st can you tell if it is hot or cold water dripping?? 2nd is the handle loose can you wiggle them and 3rd how old is the faucet I know you said it is ''New" but it could be "old" stock from his shelf in which case the gaskets/O-rings could be dried out and needs to be replaced... if loose then on top where the "c" or "H" is that cap comes off using a finger nail or small knife point pop off caps under caps there is a screw remove it but first turn off water under sink you will a bigger nut use a adjustable wrench to snug it more then try again if still leaking remove that big nut the is a washer on the bottom that will be leaking there are many sizes so you will have to buy an assortment with mixed sizes fond the two you need remove screw on bottom put new one in,,, put it all back together... ps if you have vinger you can soak old washer but this only short term fix, replace washer

need to reseat / replace "washers" in faucet ???

The pull out spout/spray has backflow preventers built into the hot and cold supply lines coming from the body of the faucet. The backflows have a tendency to lower the flow rate because of the additional restriction they cause.

There is a plastic button on the bell of the handle right by the base of the lever. It might be blue and red for hot and cold or it may be the same finish as the faucet. Remove the plug and tighten the allen screw. It takes a 3/32" allen key. If this doesn't tighten it adequately, you must remove the handle, and gently tighten the plastic retaining nut with an adjustable wrench or a channel lock pliers. The adj wrench is recommended over the pliers.

to valve is failing [need to replace the valve ]]or debris is stuck in valve either way would need to remove the valve body to inspect

General Plumbing supply... ACE is the place... True Value.. Orchard Supply, Home Depot... and at building Supply tores... AMAZON & eBay... to name a few. Carnac the Magnificent

Cal Moen and tell them you are the original owner of the faucet. They will send you parts for free.

Isn't Moen lifetime warranty

It is not a screw... Youneed a small allen key in that hole to losen-it ;)

If you look under the sink you shouls see a big nut ...all you have to do is to tighten it while holding the faucet on top at the right place