What does bus err mean - 2007 Harley Davidson FLHX Street Glide

past post of some interest
https://www.fixya.com/support/t13429513-communication_error_2_means_requires

The J1850 bus is the single wire PCI data bus, which is used by most of the electronic components for the communication in between them. The shorted to battery message means that at some point 12V is fed to this bus. Normal bus voltage measured with a digital volt meter is fluctuating between 2 and 3 volts more or less.

907 Error bus node code 7 see Err 901 2. Power supply (EW) defective.
917 Input/output model not compatible code 7 P236 code on I/O PCB incorrectly defined.
Straight from their manual. Sounds like some multiple issues.

If your blood pressure mahine is like those fro Walgreen's:
Walgreen's Blood Pressure Error Readings.
Error Codes

Err 0 No pulse is detected
Err 1 Inflation rate is too low
Err 2 Systolic reading unattainable
Err 3 Cuff pressure is too high
Err 4 Diastolic pressure is outside of operation range
Err 5 Cuff deflated too fast
Err 6 Cuff deflated too slow
Err 7 Systolic pressure is outside of operation range
Err 8 Overall pressure is outside of operation range
Err 9 Cuff is unable to inflate to the necessary pressure level

ARE YOU IN THE USA?
did you turn the keyon?
plugged in the cab OBD2 16pin dash connector .?
this connecter DLC ,on pin 16 must be at 12vdc or the tool will not work. (key on)
this pin is fused, so if fuse blows, tool is dead.

code readers, they are mostly useless.
but if compelled to use a tool that only sees 1/100th of the data. sure.

and were sold from 1995 to now
and the old tools do no work on new cars, 2004+(about) (I one many scanners from all years)

our car, (usa fed laws) uses the newer Can-bus.
and that means you tool must be Can-bus certified.
(can bus uses special pins)
pin 6 and 14 must be present on the tool and working. or tool will be DEAD.


here is your cars DLC port
F16 fuse must not be blown.(JB box)

Err 68 means
Err 68 Hold-in Relay ON. Output from the Display is short circuit. No fuel to the engine. Contact your John Deere dealer

No bus means the bus is not operating properly. It means no communication between the modules inside your jeep. All modules inside the jeep (A/C control, radio, onboard computer or trip computer, body control, etc) communicate with each other by means of a wire called bus. Check that wire.

Hello

"ERR 3" means that the magnetron units have failed in the microwave. Food will not cook or heat up when the microwave is in use.

This code is different than "ERR 1" or "ERR 2" because with those the microwave is still operational. "ERR 3" means a complete failure.

The magnetron is the main source of power and heating in a microwave. Magnets work inside a magnetron tube to create the heat and voltage needed to cook items.

Bring the microwave back to the retailer or a repair shop for service. You may also consider purchasing a whole new microwave if the prices are cheap enough.

A "P Err" readout means there is an overload in the pump/master valve circuit. A readout of "1 Err" means there is an overload in station No. 1, while "2 Err" means an overload in station No. 2 and so on, depending on the number of total stations being operated by the controller.

An overload occurs when the wiring circuit is requiring more than .56 amps of current. This overload will typically occur when the field wiring or valve solenoid is shorted, or if the field wiring is a smaller gauge than required for the application and/or distance.

Err 11, Err 12, Err 14, Err 17
Dirt or a scratch on the disc stops the laser
beam from being able to focus.
Dirt or a scratch on the disc hinders the track

Clean or replace scratched disk.


There ya go, clean or replace the cd that is displayed.