Please, I need a wiring diagram for Suzuki intruder 1996 @. my problem is when i try to put on first gear the motor turn off. i am a french people thanks
Hi, Doberu for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=1996+suzuki+intruder+1400+wiring+diagram&tbm=isch&source=univ&sa=X&ved=2ahUKEwiNl_S16vjgAhXt01kKHRnEDBEQsAR6BAgEEAE&biw=1440&bih=757
Suzuki Motorcycle Wiring Diagrams
Suzuki Intruder VS1400 Service Manual
https://www.partsfish.com/page/oem-parts-for-suzuki
Suzuki VS1400 Owner Manual
Posted on Mar 11, 2019
Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Good luck!
Posted on Jan 02, 2017
SOURCE: 94 suzuki 800 intruder. clutch splips in
No adjusting is possible.
Slip can be caused by several defaults:
- Wrong engine oil ( SAE 10w-40 API SE or SF only )
- Weak clutch springs ( free spring length : 34mm ( 1.34in ) MINIMUM
- Worn clutch disk 2(internal teeths ) ( wear limit 3.15mm ( 0.124in ) ) This is the last disk, against the clutch center
- Worn clutch disks 1 (internal teeths) ( wear limit 2.62mm ( 0.103in ) )
- Clutch plates ( thikcness between 1.55 and 1.65mm / 0.0610 and 0.0649 inches
- Damaged pressure plate ( cracks round the spring holes )
To check the clutch parts, the right engine cover must be removed.
Take attention while loosening the clutch spring bolts!
Drain engine oil, and set engine into first gear ( this locks the clutch for an easy loosening of the spring bolts )
Hope it helps
Posted on Apr 02, 2009
SOURCE: starts fine. sounds fine but dies upon putting it in gear
Your kickstand switch is either broken or out of position. The bike kills the engine as a safety feature if it thinks the sidestand is down and the bike is put in gear while the engine is running.
Posted on Apr 12, 2009
SOURCE: needs wiring diagram for suzuki banhdit gsf 650 k8
http://netfree1.blogspot.com/2008/09/suzuki-gsf650-bandit-service-repair.html
Hope this helps.
Posted on Nov 19, 2009
SOURCE: My suzuki intruder is missing backfiring on the
Did you sync the two carbs? If not the rear may be getting all the gas from the rear carb and none to the front. Twist throttle engine off and see if front carb cable is pulling the carb open.
Also unscrew the spark plug boot from the front spark plug wire and trim 1/8th inch off the wire and screw the boot back in. The plug wire end may be corroded on that wire.
Posted on Feb 08, 2010
SOURCE: Engine turns over / Petrol OK/ No Spark
i have a suzuki intruder vl 125 cc. battery ok engine turns over quick, petrol ok, just put fresh in. but no spark! bike's been stood up for a year, but was running 3 months ago, not very smooth, so i thought fresh petrol would cure it.
both plugs wet when removed, please can you help many thanks
Posted on Jul 22, 2010
Aug 17, 2018 | 2003 Suzuki VS 1400 Intruder
Aug 11, 2018 | 2000 Suzuki VS 1400 Intruder
May 19, 2018 | 1995 Suzuki VS 1400 Intruder
Feb 21, 2018 | 1995 Suzuki VS 1400 Intruder
Aug 19, 2017 | 1996 Suzuki VS 800 Intruder
Jul 19, 2017 | 1996 Suzuki VS 1400 Intruder
Jul 06, 2017 | 1996 Suzuki VS 1400 Intruder
Apr 18, 2017 | 1996 Suzuki VS 1400 Intruder
Oct 18, 2011 | 1996 Suzuki VS 1400 Intruder
Nov 02, 2019 | Motorcycles
Oct 30, 2019 | Motorcycles
117 people viewed this question
Usually answered in minutes!
×