Need wiring diagram for a hotpoint df22 dishwasher on/off switch, the switch in it has been replaced with the wrong one so i have no reference to connect up the new one. thanks

I can suggest some general steps you can take to troubleshoot the issue with the 115V outlet on your Hotpoint built-in electric stove:

1. Check the power source: Make sure the stove is properly plugged in and that the circuit breaker is on. If there's still no power, try resetting the breaker.
2. Inspect the wiring: Look for any loose or damaged wires around the outlet or control panel. If you're not comfortable working with electrical wiring, it's best to call a professional.
3. Check the outlet: Use a multimeter to check if the outlet is providing power. If it's not, it may need to be replaced.
4. Contact the manufacturer: If none of the above steps solve the problem, you can contact Hotpoint for assistance or to request a wiring diagram.

Remember, working with electricity can be dangerous, so it's important to take appropriate safety precautions and seek professional help if needed.

https://www.google.co.in/search?q=Have+Hotpoint+Dishwasher+model+DF61N+Need+wiring+diagram&rlz=1C1KMOH_enIN790IN790&tbm=isch&source=iu&ictx=1&fir=hfT4fUt27enaFM%253A%252CqTo0BQBDnQ0BcM%252C_&usg=AI4_-kSIDXjWgo94dL3QyAmXQKmlBHCuTQ&sa=X&ved=2ahUKEwiBisX1v_7eAhXDrI8KHfE-AMMQ9QEwAnoECAYQCA&cshid=1543662915079001#imgrc=hfT4fUt27enaFM:

best to consider it not safe to use until it has been tested by a qualified electrician
he could also explain what happened and the fix for the fault

This is the only wiring diagram hotpoint has on this machine.
Hope it helps

Refer this parts site. Please indicate which hose are you replacing.

Hi,
Check your heating element..
A bad heating element causes many problems in dishwashers...

Dishwasher Problems The Heating Element not Working

Dishwasher Maintenance

heatman101

Asker's Testimonial " explanation very clear. will give it a go and seehow simple it was. thanks Ronnie " - ronnieshomes

yes... check the wiring to the unit... get underneath your unit and make sure that a wire is not "grounding out" by making contact with a metal part down there on a section of unjacketed wire... this would definately trip your breaker and can blow wires apart with a pop.

there may be enough contact to get the initial display you describe... make sure all the wires are insulated properly and wire nutted together securely before resetting your breaker and checking the unit again.

It doesn't work at all If your dishwasher doesn't work at all, check these:

Power from the house Is there power getting to the dishwasher? This can be difficult to test, because dishwashers are usually wired directly to an electrical circuit, rather than plugged into the wall. But at least check for a blown fuse or a tripped circuit breaker.

Door switch The door switch is important because, if it's defective, the dishwasher won't work at all. To reach it, you need to remove the control panel cover, or sometimes the interior liner of the door. If it's defective, you need to completely replace it.

Wiring Often the main wiring connection from the house, at the dishwasher, burns and breaks the connection. If that's the problem, the wires must be repaired/replaced as necessary. If that's not the problem, check the wiring to the door switch, the wiring between the door and the lower part of the dishwasher, and the wiring to the timer. Repair any broken, burned, brittle, or defective wiring, using the proper appliance-grade wire and connectors.

Timer or selector switch Although it's uncommon, the timer or the selector switch may be defective. If so, you need to replace the defective part, because neither of these can be repaired.

Hello.
First switch off the power.
Get the cabinet door off, start by removing the side screws that hold the door (please have someone to help you, holding the door, because this doors are heavy.)
After you removed the door, remove the screws holding the fascia (about 2 on each side + 2 holding the door lock).
Remove the fascia and you wil get acess to the door lock, disconnect the wiring from the micro switch, connect the new par and reverse the process.
Cheers