My Pedometer is not showing the speed accurately --If I am traveling 35 it registers 50mph and 65 it register 110 MPH

Sounds like the speedometer is faulty. If the speed sensor were the problem, the odometer would not work correctly, the transmission would not shift correctly, and the check engine light would be on.

run fault codes and check for TCM fault.. Check for loose wiring and connections.

i had the same problem on my 99. the senor is located in the rear differential on top. speed was off, doors would not lock at speed,(15 mph) mileage comp was off, etc. sensor fixed all. good luck

Check your Tran oil pump or torque converter

takes a long time to run the rediness test since there are 6 different tests to complete...

PROCEDURE 1
EVAPORATIVE EMISSION SYSTEM LEAK MONITOR
Inspection Conditions
Engine coolant temperature: 30°C (75°F) or less (The engine is stopped before the test drive is started).
Atmospheric temperature: 5 - 30°C (41 - 113°F).
Condition of A/T: Selector lever D range.
Fuel remained in fuel tank: 30 - 50% is recommended.
Time required: 16 minutes or less after started the engine.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position. Well be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 16 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position.

PROCEDURE 2
FUEL TRIM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: -10 - 60°C (14 - 140°F).
Condition of A/T: Selector lever D range.
Time required: 30 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 30 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 3
CATALYTIC CONVERTER MONITOR
Drive Cycle Pattern
Inspection Conditions
Atmospheric temperature: -10°C (14°F) or more.
Condition of A/T: Selector lever D range.
Engine coolant temperature: Not set.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
Travel for 300 seconds or more while keeping the vehicle speed at 89 km/h (55 mph) or more.
Decelerate until the vehicle speed is within 80 km/h (50 mph) or less.
While traveling at 56 - 80 km/h (35 - 50 mph) for 10 minutes or more, fully close the throttle at least once in 2 minutes and decelerate for 10 seconds or more.
Do not repeat deceleration too often.
Vehicle speed may go below 56 km/h (35 mph) after the deceleration.
Stopping and braking are permitted. (If stopped or drive at 56 km/h (35 mph) or less for more than 5 minutes the monitoring may be stopped. In this case please restart monitoring from the beginning.)
After completing the above deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 5 times.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 4
HEATED OXYGEN SENSOR MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or more.
Atmospheric temperature: -10°C - 60°C (14 - 140°F) or more.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 - 80 km/h (35 - 50 mph) and travel for 16 minutes or more.
Stopping and braking during this operation are permitted. Keep the accelerator opening degree constant for 1 minute or more after each acceleration.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 5
EXHAUST GAS RECIRCULATION (EGR) SYSTEM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: 5 - 60°C (41 - 140°F).
A/C switch: OFF.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While traveling 16 minutes or more at 56 - 80 km/h (35 - 50 mph) with engine speed 2,000 r/min or above, fully close the throttle at decelerate for 5 seconds or more until the engine speed reaches 1,000 r/min or under.
Do not repeat deceleration too often.
Stopping and braking are permitted (Rapid deceleration and sharp steering are not permitted).
After completing the deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 8 times by fully closing the throttle valve.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 6
OTHER MONITOR (Main Components, Sensors & Switches, Wire Breakage & Short Circuit)
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature:
100°C (212°F) or less (Except engine coolant temperature sensor monitoring).
30°C (86°F) or less (Engine coolant temperature sensor monitoring).
Atmospheric temperature:
5°C (41°F) or more (Except engine coolant temperature sensor monitoring).
-10°C (14°F) or less (Engine coolant temperature sensor monitoring).
Condition of A/T: Selector lever D range.
Time required: 21 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start
Accelerate until the vehicle speed is 56 km/h (35 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 km/h (35 mph) or more and travel for 16 minutes or more.
Return the vehicle to the shop.
After stopping the vehicle, continue idling for 5 minutes, and then turn the ignition switch to the "LOCK" (OFF) position. Moreover, the vehicle should be set to the following conditions for idling.
A/C switch: OFF
Lights and all accessories: OFF
Transmission: Neutral

I had a problem with a whistling car after 50 mph and it turned out to be the front window gasket. I put silicone on the trim and problem solved.

replace a capacitor behind the panel (6.8uF 25V) with the new one.

the speedo/odometer are computer controlled by the BCM (body control module) and you may need to have The PCM re-flashed !

It is the cable that connects to the trany..

hello are the tires factory if the tires are larger or smaller than the size specified it throws yor speed sensor off speed wont register the right way if not i would say faulty speed sensor