Transmission Noise -

Low transmission fluid. Manual gearboxes normally use gear oil, automatics use transmisison fluid. Sill could be a bearing, just not a wheel bearing. Just curious, how can you tell its not a wheel bearing?

see this causes and fix it. God bless you
Tub Bearing If the washer is making a loud noise the tub bearing might be worn out, this is a common problem. The bearing can be replaced.

Clutch If the washer is making a loud noise in the spin cycle, the clutch assembly might be worn out. The clutch assembly makes the connection between the transmission and the inner tub. It is designed to allow the tub to get up to the proper spin speed gradually. As the clutch wears out it may become loud during spin or just after the spin cycle finishes. The clutch is not repairable, if it is loud or not working properly it will need to be replaced.

Drive Belt If the washer is making a loud noise the drive belt might be defective. Over time the drive belt will dry out and start cracking, eventually a piece of the belt can break off resulting in a loud noise whenever the motor is running.

Transmission If the washer is making a loud noise the transmission might be worn out or defective. There are many other more likely causes for noise from a washer. If the noise turns out to be caused by the transmission it may have to be replaced.

Transmission If the washer is making a loud noise the transmission might be worn out or defective. There are many other more likely causes for noise from a washer. If the noise turns out to be caused by the transmission it may have to be replaced.

Drive Motor If the washer is making a loud noise the drive motor bearings may have worn out. Washer motors are normally almost silent when they run. If the motor is run without a belt hooked up to it and it's loud it will have to be replaced.

Water Inlet Valve If the washer is noisy or loud, particularly when the washer is filling, the water inlet valve is at fault. Replace it.

Tub Seal and Bearing Kit If the washer is making a loud noise the tub seal and bearing kit may need to be replaced. This is a common problem and the parts are relatively easy to replace.
Rear Drum with Bearing If the washer is making a loud noise the rear drum with bearing might need to be replace. On this washer the bearing is not sold separately, the entire rear drum will have to be replaced. This is a very involved repair and will require disassembling most of the washer. However, the problem is going to get worse very quickly and so either the drum and bearing will need to be replaced or the washing machine.

Bearing If the washer is making a loud noise the bearing might be worn out. As bearings wear out from friction they gradually get worse and worse until they fail. In the meantime they get louder. If the noise primarily happens during the spin cycle the bearing is likely the problem.
Drive Pulley If the washer is making a loud noise the drive pulley might be worn out, cracked, loose or bent. Remove the drive pulley and inspect it carefully. If it is damaged or defective replace it.

Pulley If the washer is making a loud noise the pump may be worn out, or something might be caught in it. Remove the pump and inspect it for debris. If it is clear and the blades spin freely the problem might be somewhere else.
U-Joint Kit If the washer is making a loud noise the U-Joint may have failed. This is the primary drive mechanism for the agitation motion in this washer. Although this is not a very difficult repair for a DIY'er with some experience, the part is expensive and so it may be worth considering a new washer.

Motor Coupling If the washer is making a loud noise the motor coupling might have failed. The motor coupling connects the motor to the washer transmission. It is designed to fail if the washer is overloaded in order to protect both the motor and transmission

Bearing problems in the manual trannies is common, tear it down and rebuild it.

This noise is due to a part called the clutch release bearing being worn out. You must remove the transmission to replace it.

throw out bearing or worn clutch

sounds like a bad throw out bearing you have to take the tranny out to replace it.

bad throw out bearing

That's the "throw out" or "release bearing". If it makes a loud noise you'll have to take it to a shop as the transmission has to be pulled to replace it.
The clutch, pressure plate and release bearing are usually all replaced at one time....

ok the cain of noise hapen when you turn the car left or right if it does check yuo cv boots this means the front axels

Well lucky for you there is a lemon law. Bring the car in for the state inspection, Request for them to be thorough, explain that you just bought it. The past owner is responsible for the repairs. If not, get reimbursed. I'm not sure what trani fluid it takes but call the dealer for that. The noise from the front end, the grinding could be anything, check the wheel bearings, steering components, rust on rotors, backing plates, and related items. The trany noise could be nothing or it could be clutch pedal linkage, throw-out bearing, pilot bearing, or clutch asembily. It would need to be inspected to see if anything applies.