Bmw x challenge motor cycle instrument cluster failure

. When you open the door or just unlock the door the lights don't come on ?
Vehicle Security Module The vehicle security module receives inputs from the following:

• door ajar switches
• keyless entry keypad
• ignition switch
• remote keyless entry transmitter

The vehicle security module uses these inputs to control an output signal to the instrument cluster which controls the battery saver relay and courtesy lamp output.
Interior Lighting Systems The instrument cluster grounds the battery saver relay and supplies the power for courtesy lamps when any door ajar switch is opened, or the interior lamp (headlamp) switch is closed. The instrument cluster then supplies voltage to the interior lamp circuit. Vehicle speed must be less than 24 kph (15 mph) for the instrument cluster module to keep courtesy lamps on. The interior lamps will remain illuminated for up to 25 seconds after all doors are closed unless the instrument cluster module receives an input from any of the following:

• voltage from the ignition switch
• a vehicle speed signal
• input from the keyless entry keypad through the vehicle security module
• input from the remote keyless entry transmitter lock or panic switch through the vehicle security module

Do you know what body control system DTC'S - diagnostic trouble codes are ?
Instrument Cluster Diagnostic Trouble Code Index DTC Description Source Action B1342 ECU is Defective Instrument Cluster REFER to Section 413-01 . B2499 Courtesy Lamp Output Failure Instrument Cluster Go To Pinpoint Test A . B1320 Driver Door Ajar Circuit Open Instrument Cluster Go To Pinpoint Test A . B1328 Passenger Door Ajar Circuit Open Instrument Cluster Go To Pinpoint Test A . - All Other DTCs Instrument Cluster REFER to Section 419-10 .
Principles of Operation
The autolamp system provides light-sensitive automatic on/off control of the headlamps and parking lamps controlled by the vehicle security module when the headlamp switch is in the autolamps position. When the ignition switch is turned to the RUN or START position with the autolamps feature already enabled and the ambient light level is dark, the vehicle security module will request the headlamps and parking lamps be turned on. When the autolamps are disabled, the vehicle security module will request the headlamps and parking lamps to be turned off, regardless of the ignition switch position. When the vehicle security module has turned on the exterior lamps and the ignition is turned to the OFF or ACCY position, the exterior lamps will remain on for an additional time specified by the customer or the headlamp switch is turned off.
When the autolamps have been enabled and the ignition switch is in the RUN/START position, the vehicle security module will request that the exterior lamps be turned on or off based on ambient light level. If the vehicle enters darkness for at least 15 seconds, the vehicle security module will request the exterior lamps on. If the vehicle enters light for at least 15 seconds, the vehicle security module will request the exterior lamps off. By delaying turning on and off the exterior lamps during short periods of darkness and light, the vehicle security module prevents the exterior lamps from flashing on and off.

• The autolamps are inoperative - do not operate correctly

• Circuitry.
• Photocell.
• Headlamp switch.
• Vehicle security module.

• Go To Pinpoint Test G .

Power Lock
The power lock/unlock feature requests all of the vehicle doors, including the liftgate, be locked or unlocked upon a customer request from any interior door lock switch in the vehicle. The power door locking system functions independently of ignition status or vehicle speed. When the vehicle security module receives an unlock/lock command from any door lock control switch, the vehicle security module will activate relays internal to the module to supply the correct power and grounds for the door lock actuators.
Your best bet , take it to a qualified repair shop .

Did you clear codes ? . All codes in the theft deterrent module must be cleared for a relearn.
PASSLOCK Changing - Components Description
Important: Due to component variability, the vehicle theft deterrent (VTD) system must have the learn procedure performed regardless, if the vehicle starts on the first ignition cycle after a VTD repair.
All codes in the theft deterrent module must be cleared for a relearn.
Engineers design the Passlock™ system in order to prevent theft even if the various theft deterrent parts change. The Tamper mode will engage if any of the following components change:
• The Passlock™ lock cylinder
• The instrument cluster
• The powertrain control module (PCM)
If you replace any of the above components, the system will enter the long tamper mode. If the system enters the long tamper mode, ensure that the system completes a long tamper mode cycle. During the long tamper mode cycle, the THEFT indicator will flash for the full 10 minutes. The instrument cluster and the PCM require the full 10 minutes in order to complete the learn cycle. Ensure that the ignition switch remains in RUN until the indicator stops flashing. If you turn the ignition switch before the indicator stops flashing, repeat the long tamper cycle from the beginning.
Are there any codes ?
Problem
Action
The THEFT SYSTEM indicator will not light under any circumstances.
Replace the instrument cluster.
For Chevrolet vehicles, refer to Instrument Cluster Replacement .
For Pontiac vehicles, refer to Instrument Cluster Replacement .
Multiple indicators light continuously.
Test for a loss of serial data. Refer to Data Link Connector.
Instrument cluster DTC B1021 sets.
The DTC indicates a loss of powertrain control module (PCM) serial data. Refer to Data Link Connector.
Instrument cluster DTC B1022 sets.
The DTC indicates a loss of SIR serial data. Refer to Data Link Connector.
Instrument cluster DTC B1023 sets.
The DTC indicates a loss of ABS serial data. Refer to Data Link Connector.
PCM DTC P1601 sets.
The DTC indicates a loss of PCM serial data. Refer to Data Link Connector.
PCM DTC P1629 sets.
The DTC indicates PCM Theft Deterrent failure. Refer to the appropriate diagnostic table in Engine Controls.
Instrument cluster DTC B1011 sets.
Refer to DTC B1011 Passlock Cyl Data Shorted This Ign Cycle .
Instrument cluster DTC B1012 sets.
Refer to DTC B1012 Passlock Bad R-code This Ignition Cycle .
Instrument cluster DTC B1013 sets.
Refer to DTC B1013 Passlock Bad Timing This Ignition Cycle .
Instrument cluster DTC B1014 sets.
Refer to DTC B1014 Passlock R-code Unprogrammed .
Instrument cluster DTC B1015 sets.
Refer to DTC B1015 Passlock Cluster Fail Enabled .
Instrument cluster DTC B1017 sets.
Refer to DTC B1017 Passlock R-code Learn Failed .
The indicator flashes and no instrument cluster codes are set.
Refer to DTC B1013 Passlock Bad Timing This Ignition Cycle (the diagnostic table for DTC B1013).

You have no idea what your messing with . Theft light on , DTC'S - diagnostic trouble codes stored . Before you start replacing BCM an making matters worse ,do yourself a favor an take it to a qualified repair shop .
The powertrain control module (PCM) communicates with the instrument cluster using serial data over the UART serial data bus, CKT 800. When the instrument cluster determines a Pass Theft condition, the instrument cluster sends a coded password to the PCM. When the instrument cluster receives the correct password, the PCM enables the fuel injection system in order to allow the vehicle to operate normally. The PCM may allow the vehicle to start and stall quickly during a failed theft condition.

The Passlock™ lock cylinder is a locking cylinder that turns a rotating magnet past a stationary hall effect sensor. The rotating magnet creates a resistance code (R-Code) that the cylinder sends to the instrument cluster. The Passlock™ lock cylinder interfaces with the instrument cluster through a 3 wire connection. The 3 wires have the following functions:
• Power
• Ground
• Data
The THEFT SYSTEM indicator will not light under any circumstances.
Replace the instrument cluster.
For Chevrolet vehicles, refer to Instrument Cluster Replacement .
For Pontiac vehicles, refer to Instrument Cluster Replacement .
Multiple indicators light continuously.
Test for a loss of serial data. Refer to Data Link Communications System Check .
Instrument cluster DTC B1021 sets.
The DTC indicates a loss of powertrain control module (PCM) serial data. Refer to Data Link Communications System Check .
Instrument cluster DTC B1022 sets.
The DTC indicates a loss of SIR serial data. Refer to Data Link Communications System Check .
Instrument cluster DTC B1023 sets.
The DTC indicates a loss of ABS serial data. Refer to Data Link Communications System Check .
Instrument cluster DTC B1011 sets.
Refer to DTC B1011 Passlock Cyl Data Shorted This Ign Cycle in Instrument Panel, Gauges and Console.
Instrument cluster DTC B1012 sets.
Refer to DTC B1012 Passlock Bad R-code This Ignition Cycle in Instrument Panel, Gauges and Console.
Instrument cluster DTC B1013 sets.
Refer to DTC B1013 Passlock Bad Timing This Ignition Cycle in Instrument Panel, Gauges and Console.
Instrument cluster DTC B1014 sets.
Refer to DTC B1014 Passlock R-code Unprogrammed in Instrument Panel, Gauges and Console.
Instrument cluster DTC B1015 sets.
Refer to DTC B1015 Passlock Cluster Fail Enabled in Instrument Panel, Gauges and Console.
Instrument cluster DTC B1017 sets.
Refer to DTC B1017 Passlock R-code Learn Failed in Instrument Panel, Gauges and Console.
The indicator flashes and no instrument cluster codes are set.
Refer to DTC B1013 Passlock Bad Timing This Ignition Cycle in Instrument Panel, Gauges and Console.
So , do yourself a favor an have a qualified repair shop check it out .

There is no chime module ,there is a speaker inside the instrument cluster.
Door Ajar Chime
The door ajar chime feature is controlled by the smart junction box (SJB). The driver and passenger door ajar switches, and the liftgate are hardwired to the SJB. If any door or liftgate is sensed as being open, and the ignition switch is in RUN/START position, the SJB will process the input and sends a chime request to the instrument cluster over the controller area network (CAN).
Safety Belt Warning Chime
The safety belt chime feature is controlled by the restraints control module (RCM). The driver safety belt switch is hardwired to the RCM. The RCM communicates with the instrument cluster over a hardwire connection. If at any time during the first 6 seconds after the ignition switch is placed in RUN the driver safety belt is sensed as being unfastened, the RCM will process the input, and in turn, sends a chime request to the instrument cluster.
Have the vehicle checked for DTC'S - diagnostic trouble codes ,not OBD 2 codes , the check engine light has nothing to do with this .
Instrument Cluster Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1342 Instrument Cluster is Defective Instrument Cluster INSTALL a new instrument cluster. REFER to Section 413-01 . B1352 Ignition Key-In Circuit Failure Instrument Cluster Go To Pinpoint Test B . B2477 Module Configuration Failure Instrument Cluster REFER to Section 413-01 .
For a complete list of instrument cluster DTCs, refer to Section 419-10 .


Smart Junction Box (SJB) Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1342 SJB is Defective SJB INSTALL a new SJB. REFER to Section 419-10 . B1352 Ignition Key-In Circuit Failure SJB Go To Pinpoint Test B . B1577 Lamp Park Input Circuit Short to Battery SJB Go To Pinpoint Test E . C1167 Park Brake Actuator Assembly Switch Released Circuit Short to Ground SJB Go To Pinpoint Test F . Your best bet is to have a qualified repair shop diagnose this problem ,what ever it is .
Have the vehicle

I'd have to check voltage and ground for the instrument cluster. I noticed one of the fuses for your instrument cluster goes hot with the key on, same thing for ac compressor. I'd have to voltage feed to and from ignition switch for applicable fuse. Check the ignition switch wiring connector. I can't rule out ignition switch itself, at the moment.
There could be other issues?
Ignition switch faults are common on some makes and models.
Instrument cluster wiring connector problems. Sometimes if you disconnect and reconnect the instrument cluster connector, it may start working again, also, cycling the instrument cluster connector may reset, if it starts working, well, it's working for now, may quit again.
Some instrument clusters may do a self test, don't know about yours?
Press and hold odometer reset button, turn key to run position release odometer reset button, watch the odometer. Your indicator lamps may turn on and off, the gages may cycle in small increments. The cluster will exit self test on its own.
You may have to check buss circuits.

The anti theft light will flash fast on the dash if it's activated. You simply lock & unlock the doors to disarm it.

Check your inertia switch to see if it is activated. Press the rest button. Se owner manual to rest.

The control functions are contained in the instrument cluster. This module carries out all of the PATS functions such as receiving the identification code from the encoded ignition key and controlling engine enable. The instrument cluster initiates the key interrogation sequence when the vehicle ignition switch is turned to RUN or START.
The PATS uses the PCM to enable or disable the engine. The instrument cluster communicates with the PCM over the SCP network in order to enable engine operation. The instrument cluster and the PCM use sophisticated messages in order to prevent a theft. The instrument cluster and the PCM share security data (when first installed together) that makes them a matched pair. After this security data sharing, these modules will not function in other vehicles. The shared PCM ID is remembered even if the battery is disconnected. The instrument cluster also stores the vehicle's key identification code even if the battery is disconnected. There are special diagnostic procedures outlined in this workshop manual that may be carried out if either a new instrument cluster or PCM needs to be installed.
All elements of PATS must be functional before the engine is allowed to start. If any of the components are not working correctly, the vehicle will not start.
PATS uses a visual theft indicator. This indicator will prove out for three seconds when the ignition switch is turned to RUN or START under normal operation. If there is a PATS problem, this indicator will either flash rapidly or glow steadily (for more than three seconds) when the ignition switch is turned to RUN or START. PATS also "blips" the theft indicator every two seconds at ignition OFF to act as a visual theft deterrent.
The PATS is not compatible with aftermarket remote start systems, which allow the vehicle to be started from outside the vehicle. These systems may reduce the vehicle security level, and also may cause no-start issues. Remote start systems must be removed before investigation of PATS-related no-start issues.
Visual Inspection Chart Mechanical Electrical

• Ignition lock cylinder
• Encoded ignition key (PATS key)
• Use of non-encoded ignition key (key without the molded plastic head, non-PATS key)
• Use of a non-programmed encoded ignition key

• Central junction box (CJB) Fuses:
  • Fuse 2 (5A)
  • Fuse 6 (5A)
  • Fuse 30 (30A)
• PATS transceiver
• Connectors
• Ignition switch

Hello frumento, Your are describing an advance cluster failure. I have repaired many GM instrument clusters and see your issue come to my shop on a regular basics.
Please visit my website for complete repair information. www.kincerservice.com
Thanks Mike

Fuses are listed here

* = maxi fuse

1*=50A I/P fuse panel
2*=40A blower motor relay
3*= 50A 4 wheel ABS module
4*=20a Main light switch-Instrument cluster
5*=50A Ignition switch, starter relay

6*=20A Transfer case relay
7*= NOT USED
8*=20A Auto Ride Control Switch/on off switch
9*=40A Auto Ride Control relay
10*=30A PCM power relay

mini fuses
1=10A A/C relay
2=20A Aux power point
3= not used
4=15A Fog lamps-Daytime lamps
5=10A Air Bag diagnostic monitor
6=10A Powertrain Control Module (PCM)
7=30A 4WABS module
8=30A PCM relay
9=20A Fuel Pump relay and RAP module
10= 15A Horn relay
11=15A Park Lamp relay-Main Light Switch
12=30A Main light switch--Multi Function switch
13=15A Heated O2 sensors, EGR Vacuum Regulator, EVR solenoid,Camshaft position (CMP) Sensor,
Cannister Vent Solenoid, A4LD Auto Transmission
14=30A Generator-Voltage regulator


Interior fuse panel (mini fuses)

1=7.5A Power mirror switch
2=7.5A Blower motor relay,PAD module,Air Bag diagnostic monitor
3=7.5A Trailer tow connector
4=10A Left headlamp
5=10A Data link connector (DLC)
6=7.5A Air bag diagnostic monitor, Blower motor relay, Passive deactivation Module (PAD)
7=7.5A Trailer Tow connector
8=10A Right headlamp, Daytime running lamps (DRL) module, Foglight relay
9=7.5A Stop Lamp switch
10= 7.5A Speed control-amplifier assembly,Brake pressure switch, Generic electronoc Module (GEM)
Shift lock actuator, Blend door actuator, Main light switch, RABS resistor, A/C heater assembly
Flasher
11= 7.5A Instrument cluster, Main light switch, RABS resistor
12= 10A Power window relay, Washer pump relay
13= 20A Stop lamp switch, Brake pressure switch
14= 20A Rear Anti Lock Brake system (RABS) module
**10A 4WABS module**

15=7.5A Instrument cluster
16= 30A Windshield wiper Motor, Wiper Hi-lo relay, wiper run/park relay
17=7.5A Cig lighter
18=15A Drivers unlock relay-All unlock relay
19=25A PCM power diode
20=7.5A RAP module GEM module, Radio
21=15A Flasher (hazard)
22=20A Aux power socket
23=15A Turn signals
24===not used
25= 7.5A GEM module, Instrument cluster
26= 10A Battery saver relay, Electronic Shift relay, Interior lamp relay
Power window relay,Electronic shift control module, transmission control
27=15A Switch,DRL, Backup lamp switch, DTR sensor,Instrument illumination dimming control module
Dome/map lamp, GEM,electronic shift,Interior lights,Glove box lamp and switch
28=7.5A GEM module-Radio
29= 15A Radio
30=15A Park lamps, trailer Tow relay
31===not used
32=10A rear blower
33=15A Headlamps, DRL module, Instrument cluster
34=7.5A Rear integrated control panel, CD
35=10A RABS test connector
36=7.5A CD, rear integrated control panel, memory seat, Message center Attached images __________________