Question about Red Motorcycles
06 GSXR 600 was riding yesterday. 'fi' light started flashing red, the bike lost power and shut off. Will crank right back up but was sputtering and backfiring all the way home with hardly any power. @
Fuel injection issues..chec sensor wires..disconnect computr n clean pins..put some marine fuel cleanr in tank..git bike scand..buy a clymermanual
Posted on Dec 03, 2019
Lots of ideas in the GSXR Forums Eric.
FI light on. Too much oil???? ' Suzuki GSX-R Motorcycle Forums ...
https://www.gixxer.com > ... > 06-07 GSX-R600/750
Apr 16, 2008 - ... oil in a 06 gsxr 600/750 it will cause the right light to stay on and "FI" symbol ... I just an 06 750 yesterday and after riding the bike home if noticed the red light was on .... in the case the red light comes on and the oil symbol is blinking. ... As you look at it, start the engine, you should see oil moving around. F1 Code
Oct. 1, 2009
F1 light blinking
Jul. 11, 2007
Blinkin FI light??? BIke wont start! ANY HELP??
Jan. 8, 2008
FI light and bike dying
May 2, 2016
More results from www.gixxer.com
Red light, FI light, chec light - GSXR.com
https://www.gsxr.com > 7-general-gsxr-chat > 178201-red-light-fi-light-ch...
Jun 10, 2018 - It is always on when the bike is not running as it also triggered by low oil pressure. No run = no oil pressure. Normal. If the red light is on AND you have a flashing "FI" in the temp window then you have a code. FI (F1?) red light on dash
Jun. 17, 2007
F1 Light On Gsxr 750k7
Jun. 7, 2018
Red light and F1 flashing on cluster
Jun. 10, 2018
"5d" or "Sd" ERROR ??
Jun. 7, 2018
More results from www.gsxr.com
Posted on Dec 02, 2019
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
The FI message means the computer detects a problem with your fuel injection system. Problems with the power commander can cause this message, to troubleshoot it I would start by removing the power commander. You can also try disconnecting the battery for a few minutes (15 or so) to reset your bikes computer.
Posted on Apr 05, 2009
that is the code for when a bike is laid down .... auto shut off sensor ...... as soon as u turn key off and back on it should be good to go again. ....
Posted on Jun 25, 2009
SOURCE: f1 displayed
The FI light is letting you know there is a problem with the Fuel Injection system on the bike. You will most likely need to take it to the dealer and have them diagnose it with their computer. You can check your fuses and make sure they are intact, but most likely dealership problem.
Posted on Jul 16, 2009
200° is quite warm...
If the engine wont turn over, probabily you have a bad battery, a bad starter or a bad starter relay, or bad connections.
A hot engine has more compression. If the full battery power doesn't reach the starter it won't turn over...
Posted on Aug 22, 2009
you have a fi fault revmove the seat cowl on the left hand sise you will see the cdi unit (black box with wires going to it) you should see a black conector with two wires going to it bridge the wires with a pice of wire or split pin turn the igntion switch on and count the blinks one long one means ten recored the the blinks and phone a dealer and ask them for the fault code.to reset the the light pull out the bridge and the light should stay on or blink repeted turn off the switch make sure the kill switch is set to run hope this helps
Posted on Oct 29, 2009
Tips for a great answer:
FI stands for Fuel Injection. The fuel system sensors have detected a problem. It could be anything > a dirty air filter restricting airflow, a plugged injector, an error in fuel mapping, any number of things. Serious problems can trigger the computer to prevent the engine from starting until the problem is fixed. You will need to take the bike to a dealer to have them plug in a code reader. The code reader will tell you exactly what problem has been detected. There is also a chance a sensor has gone bad and is giving a false signal. Keep that in mind. Now determine if you want to do the fix or have the dealer do it. Please rate my answer.
Jul 27, 2011 | 2002 Suzuki GSX-R 600
Apr 16, 2011 | 2007 Suzuki GSX-R 600
Feb 15, 2011 | 2008 Honda CBR 600 RR
Feb 08, 2011 | 2006 Suzuki GSX-R 600
May 20, 2010 | 2005 Suzuki GSX-R 1000
Mar 27, 2010 | 2006 Suzuki GSX-R 600
Aug 19, 2009 | 2006 Suzuki GSX-R 600
Jul 16, 2009 | 2008 Suzuki GSX-R 600
Apr 05, 2009 | 2005 Suzuki GSX-R 600
73 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: