Question about Motorcycles

1 Answer

The clutch will not disengage 2002 Yamaha Raptor 660

02 raptor 660 clutch won't disengage was working fine @

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.

  • Motorcycles Master
  • 60,754 Answers

Hi, Jamie you need to repost your question under the ATV category, not Motorcycles. Thanks, Gregg

Posted on Dec 22, 2019


6 Suggested Answers


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


George Fleming

  • 142 Answers

SOURCE: Yamaha 2001 Raptor 660, need to clean my carb

Drain and replace the gas with fresh.
Remove the air cleaner and spray carb cleaner into the inlet. Work your throttle a little then put everything back together and try to start it.

Posted on Jun 02, 2009


Randy Hough

  • 2559 Answers

SOURCE: 02 raptor 660 just all of a sudden wont start just clicking sound

Try jumping the positive directly to the starter,if it starts,the solenoid is bad.

Posted on Aug 02, 2009

SOURCE: 02 dodge 2500 clutch not releasing

An hydraulic clutch line can be bled. There should be a bleeder screw on the cylinder at the end of the line running from the master clutch-cylinder.


Posted on Aug 14, 2009


  • 1 Answer

SOURCE: 02 YMF660 Yamaha Raptor won't rev

dude i have a 02 rapter 660 the reverse light was on and it wasent reving i took the battery out and took the ecu out and i found some disconnected wires fixed them and every thing was fine. if you still have a probley with it check the ecu...

Posted on Jan 06, 2010

Joe Stanton

  • 1153 Answers

SOURCE: 2000 yamaha blaster wont disengage

Its Probably Missing The 3MM Ball Between Clutch Lever Pushrod And Pressure Plate.If The Clutch Has Been Taken Apart Before This Ball Is Real Easy To Lose.

Posted on Apr 11, 2013

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Yamaha raptor 660

clutch burned up...sounds like it. pull the clutch cover off and inspect it.

Apr 29, 2014 | ATVs

1 Answer

Hi , how slack should the cable be on my raptor 660 clutch ,it's a2003 model

All clutch cables need about 1/4" slack at the handle bar. This is so the thrust rod is not constantly rubbing on the clutch thrust plate.

Feb 13, 2011 | Yamaha YZ 450 F Motorcycles

1 Answer

I have a 2001 raptor 660 that wont start off the electric start no matter wat i do. I have the repair manual an iv'e checked the spark cleaned the carbs air filter put a new choke cable in it nothing...

a common problem with those, amongst many other yamahas, is the starter clutch gear. if it's not the starter solenoid , most likely it's the starter clutch gear.

Jan 12, 2010 | 2002 Yamaha WR 426 F

2 Answers

02 YMF660 Yamaha Raptor won't rev

Check air filter, fuel filter and carb jets...
Check exhaust for obstructions and your plug wires.

Oct 13, 2009 | Yamaha XT 660 R Motorcycles

1 Answer

Raptor reverse

try loosening the clutch a little. It may be adjusted tooo tight.

Oct 06, 2009 | 2004 Yamaha XT 660 R

6 Answers

02 raptor 660 just all of a sudden wont start just clicking sound

Try jumping the positive directly to the starter,if it starts,the solenoid is bad.

Aug 02, 2009 | 2004 Yamaha XT 660 R

3 Answers

Hi I have problem with my raptor 660 runs well as I slowed my gas it my ***** and he has no power I change its spaplug did not change, is it that his can - etres the coil?

if it idles fine but when you give it gas you say you have no power? then you have a problem with your intake and exhaust valves.they need to be set.I have a 2003 660 raptor and it was doing the same thing and that fixed it.

Apr 23, 2009 | 2004 Yamaha XT 660 R

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6090 Answers


Level 3 Expert

85222 Answers

richard libby

Level 2 Expert

209 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides