Question about Motorcycles

Open Question

How do you remouve the chaine case from 1991 classic 500 seems to be holding on the top

Posted by on

  • Gregg Mahin
    Gregg Mahin Sep 23, 2019

    Hi Christian Racine, I want to help you with your question, but I need more information from you. The make of your bike would be helpful. Can you please add details in the comment box?

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove top end husqvarn 460 chain saw


To remove the top end, the carburetor must be removed as well as much of the plastic casing. The cylinder head bolts install from below. There are 4 bolts holding the cylinder assembly.

Apr 16, 2014 | Husqvarna 20" 60cc Rancher Chain Saw 460

1 Answer

2004 Kawasaki EN 500 Vulcan Classic how to replace the cam chain


Hi, Itzik for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Cam Chain Replacement Kawasaki Vulcan Forum Vulcan Forums Timing Chain Removal Help Kawasaki Vulcan 750 Forum Kawasaki VN750 Forums
Kawasaki EN500 Vulcan 500 LTD Service Manual
OEM Parts for Kawasaki 2004 Kawasaki Vulcan 500 LTD Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Dec 11, 2013 | 2004 kawasaki EN 500 Vulcan Classic

1 Answer

Replace mac 610 chain


You need to make sure the chain brake is off, pull the hand guard firmly back to the top handle, once off there should be nothing else holding the cover on, so it is just a case of pulling it off.

Oct 24, 2012 | McCulloch 16 Inch Gas Chain Saw MCC1635AK

1 Answer

I need to adjust the cam chain tension on a 1980 honda cx 500 custom. Where is it located and how do i do it? Do you have any pics that can be attached?


Take off the tappet hole inspection cover behind the cylinder on top of the engine case. Remove the tappet hole inspection cover underneath the radiator in the front of the motor. Put a 17 mm socket on an extension with a breaker bar in the front hole and turn the motor over manually until the top dead center (TDC) mark for the number 1 cylinder appears in the other hole.behind the right cylinder is a gold 10 mm bolt coming out of the back of the block. Loosen it one turn and re tighten it. You have just adjusted your cam chain. If you ever have to take off the rear cover to replace the water pump seal and you just happen to have a cx650 self adjusting cam chain tensioner, it will fit right in so you can forget about adjusting your cam chain ever again.

May 25, 2010 | 1980 Honda CX 500 A

1 Answer

Can i adjust cam chain tensioner in kawasaki EN 500 1992, if not is it possible to fit manual cam chain tensioner.


no, it is automatic adjustment only, once it has reached it's end, you must replace the chain

May 04, 2010 | 1996 kawasaki EN 500 Vulcan Classic

1 Answer

Yamaha SR 400 timing chain


Hi There honzakot
Yup, SR400 and 500 are the same engine in this respect. Seems most top end parts for the 500 fit the 400. . Check this link (yoshimura) for some supporting evidence. sr400 jumps straight to the SR500 at Bike Bandit also.
regards robotek

Apr 19, 2010 | 2001 Yamaha SR 400

1 Answer

How do I change the headlight? (passenger side)


There are three screws that holds the head lamp in place, but first you have to remove the right side radiator cover, remouve the front grill (4 screws), remouve the head lamp lower trim (one screw behind the grill and cliped at the fender), then remouve the front grill mounting bracket (2 screws) then you'll finaly reach the 3 headlamp screws (2 on top and one behind the lower headlamp trim)
Good luck
Slant6Nova

Oct 24, 2009 | 1998 Cadillac Catera

1 Answer

How many bolts are on the outside of the crank case on a 1991 harley soft tail


Are you talking about the bolts that actually hold the right and left case halves together or some other bolts? On a stock setup, there are six double ended threaded studs with nuts and two hex head bolts.

Sep 27, 2009 | 2003 Harley Davidson FLSTC Heritage...

1 Answer

Chain check and maintenance


Depending on how aggressively you ride, chains should be inspected every 500-700 miles, or roughly twice a month

Nov 10, 2008 | 1991 Honda ST 1100 Pan European

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5962 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

richard libby

Level 2 Expert

209 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...