Fi light blinks 6 times

SOURCE: Overdrive light on gear shifter is blinking?

The overdrive light blinking indicates a code has been stored in you computers transmission control module, the cost will depend on the problem, some have had problems with the torque convertor clutch slipping, could be more major, get the code pulled out and I can provide you with a more complete answer. -Jared

SOURCE: Sony KF-50WE610 flahing red light (6 blinks)

Jeff, did you look at the Sony web site? They had a problem with 9 different TV models that were from 2003 and 2004, KF-42WE610, KF-50WE610, KF-60WE610 and 6 other models.
This is what it states: It haas come to our attention that a limited number of Grand WEGA rear projection TV's may exhibit warping to the lamp access door. In rare cases, some additional components may also become damaged as a result. and so on........
You probably have some components melted on the inside around the lamp. I have a 42 inch and I just replaced the lamp at Christmas and the door was melted shut. This is the second lamp that I have replaced, the door was starting to melt the first time. They never sent me anything about this problem, and as of today I am still trying to work something out with them. The repair shop who has it told me that it can't be repaired. The parts that are melted are not in stock and they don't make them anymore. They are supposed to get back with me and make me some kind of offer.
They will only fix this problem through March 31, 2009.

SOURCE: The display at top of stove is showing "F1" and continuously beep

Maytag Range / Stove / Oven Fault Codes Failure Code Fault Code Description Solution F0 Function key stuck Replace touch pad or if touch pad is part of the clock, replace the clock (ERC). F1 Defective touch pad or clock (ERC) Replace touch pad or clock (ERC). Touch pad is a more common problem. Refer to F1 test at the top of this page for more information. F2 Oven temperature too hot Replace relay board, if present, or oven temperature sensor (RTD). Check sensor harness. F3
or
F4 Shorted or open oven temperature sensor (RTD) Check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok. F5 Watchdog and hardware conflict Replace clock (ERC). F7 Function key shorted or stuck Replace touch pad or if touch pad is part of the clock, replace the clock (ERC). F8 Analog / Digital problem Replace clock (ERC). F9 Door latch Check door latch components.

SOURCE: 2003 ford ranger airbag light is flashing code

46--- Driver Pretensioner Circuit Resistance High

That means the buckle in you driver side seat belt system has failed. It has an explosive device called a pretensioner in it which is designed to pull you into place microseconds before the airbag deploys. That component has failed and has deactivated the airbag system. You will need to replace the 'buckle pretensioner'.
But before you do, please get real familiar with the system you are working on before you cause additional damage, hurt yourself or deploy the bags accidentally.

http://www.airbagsolutions.com
http://www.airbagsolutions.com/vehicles_list.aspx
http://www.airbagsolutions.com/demo.aspx

SOURCE: Sony LCD Model KF-60WE610 lamp was replaced and

For Sony Model KF-60WE610, KF-50WE610, and KF-42WE610, the Diagnostic Code of power light indicator flashing 6 times green, then flashing 6 times red (6 red etc), means you need to replace part number A-1302-272A G1 BOARD, COMPLETE. See Sony Service Manual, 4. Chasis-1 at part Ref no. 103. The Power Board sits vertically in two slots on the left side of the electronics board. 4 wire connectors to remove when replacing. This component fits all 3 KF models listed above.