Question about Motorcycles

Open Question

PVL 3702/201/2015 - Motorcycles

Posted by on

  • Gregg Mahin
    Gregg Mahin Aug 18, 2018

    Hi, Amanda I would really love to help you with your motorcycle question but due to the magnitude of yesterday's solar flare the batteries in my crystal ball are dead and my mental telepathy headset circuitry was melted. I need the year, make, and model of your motorcycle please click on " Ask For More Information" directly below and provide this information in the box that will open and then click on the green "SEND" box in the bottom right-hand corner. Good luck and have a wonderful day.

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the vacuum lines on a 1999 quest cruise control


https://www.youtube.com/watch?v=jgN1HMonEAs
https://www.youtube.com/watch?v=yE7CrEQHdoo
in the video below notice how he found the cable for the accelerator and traced it back to a round device against the firewall. This device is an actuator the vacuum line will connect to the back of this device and follow this vacuum line back to the cars vacuum pipes.
https://www.youtube.com/watch?v=crR7Mw8X1vI

https://www.youtube.com/watch?v=pvL-YbDOVXM



Jun 05, 2017 | Cars & Trucks

1 Answer

How to troubleshoot a motoplat mini 6 ignition for a 495 KTM dirtbike


Hi im guessing your year to be 1981 or 1982.First if you have not done so make sure your coil is grounded.Next disconnect your kill switch.Next check the primary side of the coil .3 to .5 ohms check the secondary side of the coil 5k to 7k ohms with out the spark plug cap.While your at it check for spark with out the cap.Make sure your kicking it fast as motoplats do not spark below 700 rpm.If all else fails you have a few choices .Vance smith can rebuild yours for under 200.00 usally.You can go with a pvl ignition for around 500.00.Also make sure your crank bearings are tight and your mag side crank seal is not leaking if you smell fuel in the mag cover you need to replace your crank seal good luck

Jul 10, 2015 | KTM Motorcycles

1 Answer

Where to download a driver of ASUS PVL-D Motherboard Intel Corporation Graphics Adapter?


You can download the device drivers from ASUS WEB site.Select your model motherboard/computer/laptop, and make sure you select driversthat matches your Windows operating system. Please click on this link to theirWEB support site : - http://support.asus.com/download/download.aspx?SLanguage=en-us

Jun 07, 2011 | ASUS PVL-D Motherboard

1 Answer

Projector problem


I had this happen too. Occasionally, you will press the power button, but it won't shut down, everything else seems to work. I was forced to unplug it a few times which is a bad deal. I finally traced it to some kind of strange power loop from my DVD player. If you have multiple sources, I'd try it for a while without them (one at a time) and see if you can isolate it, or better yet, if you have a way to swap them all out temporarily and add them back 1 at a time, you may be able to isolate it. It didn't seem to help to unplug or disconnect the DVD player before powering off the projector. It had to have never been connected. Took me quite a while to figure it out. It's pretty obscure, hope it helps.

Feb 17, 2009 | Sanyo PLV-Z2 Multimedia Projector

2 Answers

Maintenance


gas/oil ratio should be 40:1 synetic.empty tank drain carb bowl thats it l have 92 250 exc. It has fmf pipe &silencer boyesson rad valve, been ported ,crank has been balanced,PVL ignition. I use spectro synetic 36;1 to keep it well lubed at wide open. ,,,

Nov 10, 2008 | 2005 KTM MXC 300

1 Answer

Maintenance


gas/oil ratio should be 40:1 synetic.empty tank drain carb bowl thats it l have 92 250 exc. It has fmf pipe &silencer boyesson rad valve, been ported ,crank has been balanced,PVL ignition. I use spectro synetic 36;1 to keep it well lubed at wide open. ,,,

Nov 10, 2008 | 2005 KTM EXC 300

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6103 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

richard libby

Level 2 Expert

209 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...