Question about Motorcycles

Open Question

There isn't any jets that work.How can I fix it?

Posted by on

  • Gregg Mahin
    Gregg Mahin Mar 04, 2018

    Hi, Brenda I would really love to help you with your bike question but due to the magnitude of yesterday's solar flare the batteries in my crystal ball are dead and my mental telepathy headset circuitry was melted. I need the year, make, and model of your motorcycle please click on " Ask For More Information" directly below and provide this information in the box that will open and then click on the green "SEND" box in the bottom right-hand corner after it posts I will receive an "ALERT" icon that will allow me to respond to your information. Good luck and have a wonderful day.

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cuts out when I increase the throttle


Blocked fuel injector in the carb, usually gunk in bottom of tank gets pulled through into carb so idle jet is ok but when you give it the beans the main injector is blocked and the idle jet isn\'t enough to produce increased power demand, ends up just sucking in air only.

also timing, leads, coil. check plug too. Red.

Apr 04, 2014 | 2011 Derbi Senda DRD 125 R

1 Answer

Pride Jet 3 Ultra 4500 rpm, unit is completely dead, am I missing an auxiliary charger or is it built into the unit?


I suggest that you start with determining the condition of your batteries and work outwards from there. Dead batteries just don't want to take a charge. Test your batteries with a meter before you start part swapping. The internal charger is only about 4 amps so it will take many hours to charge a 24volt system.

May 06, 2013 | Jet 3 Ultra Power Chair

2 Answers

Window washing fluid pump isn't working. Hums and runs, but no fluid comes out. Any ideas?


1. the washer fluid jets are plugged possibly and will not allow fluid to discharge. Take a small wire or needle and stick into the jet end where the fluid comes out and it should spray after that if that is the issue.
2. the lines coming from the washer pump could be broken or cut open. Remove the line at the back of the spray jet either at the hood or at the wiper arm, then attempt to spray the wiper fluid. If it does not spray then there is an open/broken line coming from the washer pump or the pump may have a problem. If fluid is coming out of the line, the jet again is plugged up. Also check to see that fluid is going into the washer pump (locating the pump and getting to it is sometimes not so easy depending on where the mfg put the pump).

Jan 18, 2013 | 1986 Buick Century

1 Answer

Cant connect my jet to an ad hoc network


First Option:
Phone in the Other Sim and check the Phone Network Signal If Network Signal Problem not Solved So
Secend Option:
Your Phone Network IC Fault So Please change Network IC
And Network Signal Problem will Solved
if it is there isn't much you can do on this side of the network.
Contact your phone company.

Jul 29, 2012 | Samsung s8003 Jet Unlocked Phone with Full...

1 Answer

The sound wont work. I replaced batteries and still nothing.


most likely, there's a connection problem with the speaker. try opening that section and re-soldering the wires to the speakers. if there's a "mute" or "off" button.. make sure that isn't activated as well

Aug 12, 2011 | Hot Wheels Hotwheels Turbo Jet City

1 Answer

My champion 18 inch 3.5 hp petrol lawn mower has stopped working correctly. it is around 15 years old but worked really well up till now. it will start every now and again, chug then on touching grass it...


sounds like you may have a clogged jet inside the carb. You will have to remove the carb, and remove the jet to unclog it. Once the jet is clean, hold it up to the light to make sure it is 100% clear before reinstalling it.

Feb 16, 2018 | Garden

1 Answer

My srm3800 runs but when itry to use it it seems to cut off like not geting fuel it idle go but it will cut off aftet I give it gas


Check there are no kinks in fuel line.
Make sure that the air filter isn't blocked.
Check the throttle cable is operating the throttle plate in the carburettor ok.
Ensure chain isn't too tight.
The carburettor should be a tight fit on the air inlet manifold.
It's possible that some of the jets could be blocked in the carburettor. You can try and clean these with compressed air but ensure you remove any seals gaskets, springs on the diaphragm pump , primer bulb etc as they can be damaged by the pressure.
If the the choke normally disengages when the throttle trigger is squeezed, check this is working ok.

May 08, 2011 | Echo Garden

1 Answer

My Canon ip3600 has full ink, there is paper in the tray. It will print the page I want it to print. However, there isn't any ink / text on the pages that are being printed


It sounds like either the ink cartridges are clogged, or if you've installed new ones, it could be you forgot to remove the tape that covers the ink jet on them. If clogged, you can use alcohol on a Q-Tip to clean the jets.

May 06, 2011 | Canon PIXMA iP3600 Photo Printer

2 Answers

How do you set the timing on a 01 yamaha yz 125 or why else would it be melting the spark plug prob off with a 32:1 fuel mix and the plug that goes in the bike from the factory


melting spark plug is too lean. exhaust gas high temps caused by too much air. your oil to fuel ratio is correct, but your air to fuel ratio is not. adjust your needle clip position to add more fuel to the carb by lowering the C clip. this will raise the needle, giving you more fuel for the same amount of air. also check air filter element for tears.

Nov 22, 2010 | 2003 Yamaha YZ 125

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5962 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

richard libby

Level 2 Expert

209 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...