Question about Motorcycles

Open Question

Getting air through needle - Motorcycles

Posted by on

  • Gregg Mahin
    Gregg Mahin Aug 28, 2017

    Hi, Wayne I would really love to help you with your bike question but due to the magnitude of yesterday's solar flare the batteries in my crystal ball are dead and my mental telepathy headset circuitry was melted. I need the year, make, and model of your motorcycle please click on the word "COMMENT" below and provide this information in the box that will open and then click on the green comment box in the bottom right-hand corner after it posts I will receive an "ALERT" icon that will allow me to respond to your information. Good luck and have a wonderful day.

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a toro zero turn that seems to be getting too much gas.


needle and seat not controlling the fuel level from dirt under the needle
blocked air filter

Aug 28, 2016 | Toro Heavy Machinery

1 Answer

I'm having a problem with my finish line flg 3.. I'm getting air bubbles blowing back up into the cup of my gun causing the paint to spit out when I try to spray.. Is there any reason this would be...


Make sure that the vents on the gun are clean and if the problem is still present then you have a problem with wear on the bushing or the needles. Air is blowing back into the cup before the needle is opening enough. So this could be a pressure, timing or wear issue.

Nov 25, 2013 | Air Tools & Compressors

1 Answer

Which setting do I use for the needle in my carb?


How many miles?? The needle jet/jet needle (brass kit) may need replacing ...they wear out due to vibration and cause the spark plugs to turn black, get poor milage, and then "carbon foul".
Try running it without the air filter for a few miles.. see if that makes it run better. If so, I would replace the air filter and put a new brass kit in the carburetor.
You can try moving the CLIP on the needle UP to the second to the top position, OR the top position..that will lean out the mixture/carburetor.

Kawasaki Vulcan 1500 Classic 1996 2004 Service Repair Maintenance

Sep 28, 2017 | 2002 kawasaki VN 1500 Vulcan Classic

1 Answer

Ihave 50 ge ptac units that only the middle of evap.is getting cold


short of gas. Check for leak and arrest it. Then vacum and do gas charging.

Aug 18, 2012 | GE Zoneline In Wall Ptac Unit Air...

1 Answer

I'm having low mpg with my 2001 harley ultra classic. Bike is stock with aftermarket pipes. Everything I do it goes to 22 to 24 mpg. I'm getting 29 to 30 and manuel and others tell me I should be...


Hi Robmil07, and the usual suspects are:
1. Excessive enrichner use.
2. High speed riding style.
3. Idle speed improperly adjusted.
4. Dirty air cleaner element.
5. Vacuum piston assembly malfunction.
6. Excessive accelerator pump output.
7. Plugged or restricted bowl vent.
8. Fuel level too high.
9. Loose jets.
10. Worn or damaged needle or needle jet.
11. Enrichner valve not seated or leaking.
12. Plugged air jets or passages.
Good luck and have nice day.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Nov 02, 2011 | 2001 Harley Davidson FLHTCUI Electra Glide...

1 Answer

I have a 1986 700 fazer on a buggy it has a dynajet stage one kit in it K&N air filter pipes are not stock it runs good at high RPM when at low RPM it runs like its getting to much fuel it has...


If the engine is too rich at low rpm then yes it will help if you drop the needles and consider maybe turning the air correction screws out a fraction to increase the air to the pilot jets or using smaller pilot jets altogether. Hope that helps you.

Sep 24, 2011 | Yamaha FZS 600 Fazer Motorcycles

1 Answer

We are having trouble getting the spray gun to pull the paint through. It will spray air but does not spray paint.


when you pull the trigger can u see the needle moving backward? if so, then it's either the paint is too thick compare to the nozzle size or the passage for paint is blocked. try to take the nozzle, needle and the cup off and give it a good clean!

Sep 05, 2011 | Campbell Hausfeld Husky Gravity Feed HVLP...

1 Answer

Engine not getting gas.


If the fuel is getting past the fuel filter the issue could be a stuck needle valve in the carburetor. If the carburetor has a drain button on the bottom of the float bowl push it to ensure fuel flows freely for several seconds, if there is no drain plug or button pinch shut and disconnect the fuel line from the inlet to the carburetor, direct the line into a clean container and remove the pinch clamp, if fuel flows freely the filter is not clogged, if the fuel does not flow well replace the fuel filter.
To unstick a needle valve use a short blast of low pressure air (5-7 psi) into the carburetor fuel inlet, if the needle valve is stuck the air will tend to all blow back, once the valve opens you will here a change in tone. If you do not have access to adjustable compressed air try tapping the side of the carburetor gently, if it remains stuck you will have to remove the float bowl to gain access to the float and needle valve.

May 26, 2009 | Craftsman Garden

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5971 Answers

Marvin
Marvin

Level 3 Expert

85216 Answers

richard libby

Level 2 Expert

209 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...