Question about 1995 Honda GL 1500 SE Gold Wing

1 Answer

Looking for an on line guide to replacement of air pump for 1995 goldwing. If no on line guide can someone help with directions on replacing the air pump.

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

First remove bike from airpump then reassemble! there is no easy way to do this and it really is a case of buy a manual or in a methodical manner and a camera, strip the bike down from the rear piece by piece until you can remove the unit and fit a new one.

Posted on Jul 28, 2009


1 Suggested Answer


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 1993 honda goldwing. When i try to pressure up the rear suspension, I hear the air pump working, but the suspension pressure does not increase. can you help me?

You either have a leaking air line , but more likely you have blown a rear shock seal. You can replace the seal yourself. The seals will cost about about $20 per shock and $7 for a bottle of rear shock oil.

May 10, 2011 | 1993 Honda GL 1500 Aspencade Gold Wing

1 Answer

Brakes are not working and filling it with brake fluid doesnt seem to work. how can you check the brake lines and how do you now if one is broken on a 1995 cutlas ciera oldsmobile?

Fill the master again and have someone pump the brake while you watch underneath the car. You will see fluid coming out wherever the leak is. When replacing a broken line, it is unsafe to use a compression fitting with ferrules. Always replace a complete line from fitting to fitting. It is OK to join lines using a fitting made for flair ends in order to ease installation and obtain the proper length.
You do not need to exactly follow the original routing providing you secure the line so it does not vibrate and so it is away from sharp edges, linkage for trans and steering and exhaust pipes.
You should also check wheel cylinders, calipers and the rear of the master cylinder itself for signs of seepage as they can also leak. Always bleed the system to clear it of air after doing any hydraulic repair.
If you have never done any work of this kind before, it's wise to obtain a chilton or haynes manual to guide you. They are inexpensive and will also help with any future repairs!!!
Any questions? Just ask!!

Jan 30, 2011 | 1995 Oldsmobile Cutlass Ciera

2 Answers

How to change a fuel pump?

Remove the fuel tank from the vehicle, Remove the locking ring from the fuel pump module, remove the fuel pump module, reverse steps to install.

Jan 15, 2011 | 1995 Plymouth Grand Voyager

1 Answer

How do i replace broken brake line just before brake hose connection left front line

you may need a pair of visegrips and a 10mm wrench.after replacing the line you must bleed your will need a helper fill up brake fluid have someone to pump up brakes hold down pedle brake lose the bleeder on the caliper let the air out tigten it re pump re repeat until no air keep an eye on the fluid.

Aug 26, 2010 | 1995 GMC Sierra

1 Answer

Replaced the fuel pump twice. still no pressure. possible air lock or bad relay, or bad regulator for injectors or i'm stumped . what should i check next?

Check your pressure from the pump directly. If you have pressure there replace your filter. If you still have no pressure, it is very possible you have a clog in your line. Disconnect at both ends and use an air compressor to blow the line out. Not an air lock for sure. Possible regulator if all else fails.

Aug 09, 2010 | 1995 Pontiac Bonneville

1 Answer

Replaced wheel cylinders and calipers - could not

alot of air in the lines,probably the rears,fill up the master cylinder and loosen the bleeder screws on the rear and let them drip for 10-15 minutes,may not drip at all so thats air in it,tighten them up and pump the brakes about 20 times and hold them,have someone release the bleeders 1 side at a time with the pedal still down,then pump again about 15 times,do the same process,what you want to do is compact the air as far down to the wheel cylinders as possible so when you loosen them more air comes out with the fluid.

Feb 04, 2010 | 1995 Ford Bronco

1 Answer

Honda goldwing 1100 1981 i bought an air pump pluged into the cigerette lighter and blew a fuse i hope everything else works but the radio and the cigerette lighter can you help?

A better answer than 'just replace the fuse', is to install a new lighter socket near the battery with a new fuse holder and a heavy enough fuse and wiring to sustain the current draw of the air pump. Connect the wiring (with fuse) directly to the battery connections. Hope this helps.

Oct 19, 2009 | 1981 Honda GL 1100 Innerstate Gold Wing

1 Answer

The 1995 goldwing is idling between400 to 700

try running sea foam through the tank sounds like you hace some varnish in the carbs

Aug 21, 2009 | 1995 Honda GL 1500 SE Gold Wing

1 Answer

Stearing pump nnoise 1995 toyota tacoma

you may have air in the lines to the steering rack. or the fluid is low. there is also a chance your replacement pump is defective. a lot of steering pumps are remanufactured. a way to check for air in the lines is to take the filler cap off, have someone turn the steering wheel lock to lock a few times and hold for a few seconds at full lock each time, check to see if any air bubbles arise in pump reservoir. if no bubbles are seen you can also try a vacuum pull on the reservoir if you have the tool to do so, that tool will pull any air from the lines, but the engine has to be off because it will also pull some fluid from the pump in the process, when you don't see any air bubbles in the vacuum tools's lines it should be ok.

Jan 03, 2009 | 1995 Toyota Tacoma

1 Answer

1995 Chevrolet Blazer

in order to replace a breakline you must first measure the line then go to your nearest autoparts store and give them the measurements of the line and inform them what vehicle its going in to. then with a wrench disconnect both ends of the line. then replace it with a new one. make sure no liquid drips off of the other brakeline. then fill up the mastercylinder which is located under the hood. thats where you fill it up with brake fluid.then have someone pump the brakes 5 times holding on to the brakes loosen a nipple on the disk brake or drum depending where the line is located its with a 10mm depending on the vehicle while still pressing the brakes tighten the nipple. then redo the pumping until all the air is out the liquid will start to purge out. remember to fill the master cylinder.

Dec 17, 2008 | 1995 Chevrolet Blazer

Not finding what you are looking for?
1995 Honda GL 1500 SE Gold Wing Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5971 Answers


Level 3 Expert

85216 Answers

richard libby

Level 2 Expert

209 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides