Question about 2007 Harley Davidson FXDB Dyna Street Bob

1 Answer

CHECK ENGINE LIGHT COMES ON AT START UP AND IDLE. NO ROUGH IDLE NO SYMPTOMS?????

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Harley Davidson Master
  • 1,562 Answers

Have you pulled the error codes?

1- Turn Ignition switch to OFF & Run/Stop switch is to Run.
2- Push odometer reset button in & hold.
3- Turn ignition switch to Ignition and release odometer reset button. Background lighting sould illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word "diag" should then appear.
4 - Push the odometer reset button once and you will see the selection menu "PSSPt" with the first P flashing.
5 - Each letter represents an area of the diagnostics module. The module that is flashing is the one you are going to check. To move from one letter (module) to the next, you push the odometer reset button one time. (from P to S to SP to t and back to P, etc.)
P = ECM/ICM (Electronic Control Module [EFI] / Ignition Control Module [Carbureted])
S = TSM/TSSM (Turn Signal/ Turn Signal Security Module)
SP = speedometer
T = tachometer
6 - To get the DTC within an area of diagnostics, push and hold the odometer reset button in for 5 seconds and release. If there are any DTC's the code will be displayed or the word "none" will appear if there are no DTC's. Push the odometer reset button again to view additional codes if they exist.
7 - Record the codes.
8 - If DTC's are not to be cleared, Press and release the odometer reset button. Part number of module will be displayed.
NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until 'clear' comes up. Release the odometer reset button. Turn OFF the ignition switch. Run your bike and shut it down then recheck the DTC's again by repeating steps 1 to 9. If the code is current it will reappear.
9 - Press and release the odometer reset button to continue to the next module.
10 - Turn Ignition switch to OFF.

What do the codes mean?

DTC FAULT CONDITION MODULE
"BUS Er" (TSM/HFSM) Serial Data Open/High
B0563 Battery Voltage High (TSM/TSSM)
B1004 Fuel Level Sending Unit Low (Instruments)
B1005 Fuel Level Sending Unit High/Open (Instruments)
B1006 Accessory Line Overvoltage (Instruments)
B1007 Ignition Line Overvoltage (Instruments)
B1008 Reset Switch Closed (Instruments)
B1121 Turn Signal Will Not Flash (HFSM)
B1122 Right Turn Signal Open (TSM)
B1123 Left Turn Signal Short-to-Ground (HFSM)
B1124 Right Turn Signal Short-to-Ground (HFSM)
B1125 Left Turn Signal Short-to-Voltage (HFSM)
B1126 Right Turn Signal Short-to-Voltage (HFSM)
B1134 Starter Output High ((TSM/TSSM)
B1135 Accelerometer Fault ((TSM/TSSM)
B1136 Accelerometer Tip-Over Self Test (HFSM)
B1141 Ignition Switch Open/Low (HFSM) ONLY
B1141 Turn signals Will Not Flash (TSM) ONLY
B1142 Internal Fault (HFSM)
B1143 Security Antenna Short-to-Ground (HFSM)
B1144 Security Antenna Short-to-Battery (HFSM)
B1145 Security Antenna Open (HFSM)
B1151 Sidecar BAS Low ((TSM/TSSM)
B1152 Sidecar BAS High ((TSM/TSSM)
B1153 Sidecar BAS Out of Range ((TSM/TSSM)
B1154 Clutch Switch Short-to-Ground (TSM/HFSM)
B1155 Neutral Switch Short-to-Ground (TSMHFSM)
B2006 Radio Switches Shorted/Stuck (Audio)
B2007 Handlebar (Audio) Switch Shorted High(Audio)
Handlebar Mode Switch Shorted High(Audio)
Handlebar PTT/Squelch Switch Shorted High(Audio)
B2008 Handlebar (Audio) Switch Shorted Low(Audio)
Handlebar Mode Switch Shorted Low(Audio)
Handlebar PTT/Squelch Switch Shorted Low(Audio)
B2009 Handlebar (Audio) Switch Stuck or Open(Audio)
Handlebar Mode Switch Stuck or Open(Audio)
Handlebar PTT/Squelch Switch Stuck or Open(Audio)
B2010 Passenger (Audio)/PTT Switch Shorted High(Audio)
Passenger Mode Switch Shorted High(Audio)
B2011 Passenger (Audio)/PTT Switch Shorted Low(Audio)
Passenger Mode Switch Shorted Low(Audio)
B2012 Passenger (Audio)/PTT Switch Shorted Stuck or Open(Audio)
Passenger Mode Switch Shorted Stuck or Open(Audio)
B2013 Sidecar Switches Shorted High(Audio)
B2014 Sidecar Switches Shorted Low(Audio)
B2015 Sidecar Switches Shorted Stuck or Open(Audio)
B2016 Front Speakers Shorted(Audio)
B2017 Front Speakers Open(Audio)
B2018 Front Speakers Shorted to Ground(Audio)
B2019 Front Speakers Shorted to Battery(Audio)
B2020 Rear Speakers Shorted(Audio)
B2021 Rear Speakers Open(Audio)
B2022 Rear Speakers Shorted to Ground(Audio)
B2023 Rear Speakers Shorted to Battery(Audio)
B2024 Sidecar Speakers Shorted(Audio)
B2025 Sidecar Speakers Open(Audio)
B2026 Sidecar Speakers Shorted to Ground(Audio)
B2027 Sidecar Speakers Shorted to Battery(Audio)
P0107 Map Sensor Open/Low (EFI)
P0108 Map Sensor High (EFI)
P0112 IAT Sensor Voltage Low (EFI)
P0113 IAT Sensor Voltage Open/High (EFI)
P0117 ET Sensor Voltage Low (EFI)
P0118 ET Sensor Voltage Open/High (EFI)
P0122 TP Sensor Open/Low (EFI)
P0123 TP Sensor High (EFI)
P0131 Front O2 Sensor Low (EFI)
P0132 Front O2 Sensor High (EFI)
P0134 Front O2 Sensor Open/Not Responding (EFI)
P0151 Rear O2 Sensor Low (EFI)
P0152 Rear O2 Sensor High (EFI)
P0154 Rear O2 Sensor Open/Not Responding (EFI)
P0261 Front Injector Open/Low (EFI)
P0262 Front Injector High (EFI)
P0263 Rear Injector Open/Low (EFI)
P0264 Rear Injector High (EFI)
P0373 CKP Sensor Intermittent (EFI)
P0374 CKP Sensor Synch Error (EFI)
P0501 VSS Low (EFI)
P0502 VSS High/Open (EFI)
P0505 Loss of Idle Sped Control (EFI)
P0562 Battery Voltage Low (EFI)
P0563 Battery Voltage High (EFI)
P0603 ECM EEPROM Error (EFI)
P0605 ECM Flash Error (EFI)
P0661 Active Intake Solenoid Open (EFI)
P0662 Active Intake High/Shorted (EFI)
P1001 System Relay Coil Open/Low (EFI)
P1002 System relay Coil High/Shorted (EFI)
P1003 System relay Contacts Open (EFI)
P1004 System Relay Contacts Closed (EFI)
P1009 Incorrect Password (EFI)
P1010 Missing Password (EFI)
P1351 Front Ignition Open/Low (EFI)
P1352 Front Ignition Coil High/Shorted (EFI)
P1353 Front Cylinder No Combustion (EFI)
P1354 Rear Ignition Coil Open/Low (EFI)
P1355 Rear Ignition Coil High/Shorted (EFI)
P1356 Rear Cylinder No Combustion (EFI)
P1357 Intermittent Secondary Front (EFI)
P1358 Intermittent Secondary Rear (EFI)
P1475 Exhaust Actuator Position Error (EFI)
P1477 Exhaust Actuator Open/Low (EFI)
P1478 Exhaust Actuator Shorted (EFI)
U1016 Loss of ICM/ECM Serial Data (Instruments)
U1016 Loss of Serial Data(Audio)
U1016 Loss of ECM Serial Data (TSM/HFSM))
U1064 Loss of (TSM/TSSM) Serial Data (EFI)
U1064 Loss of (TSM/TSSM/HFSM) Serial Data (Instruments)
U1097 Loss of Speedometer Serial data (EFI)
U1255 Missing Message at Speedometer (EFI)
U1255 Serial Data Error/Missing Message (EFI)
U1255 Serial Data Error/Missing Message (Instruments)
U1255 Serial Data Error/Missing Message (TSM/TSSM/HSFM)
U1300 Serial Data Low (EFI)
U1300 Serial Data Low (Instruments)
U1300, U1301 Stalls, then Starts(Audio)
U1300 Serial Data Low (TSM/HFSM)
U1301 Serial Data Open/High (EFI)
U1301 Serial Data Open/High (Instruments)
U1301 Serial Data Open/High (TSM/TSSM)
U1302 Infotainment BUS Shorted Low/High(Audio)
U1306 Infotainment BUS Lost Communications with Hands free Phone Module(Audio)
U1307 Infotainment BUS Lost Communications with CB Module(Audio)
U1313 Infotainment BUS Lost Communications with XM Module(Audio)
U1314 Infotainment BUS Lost Communications with Navigation Module(Audio)
U1317 Infotainment BUS Lost Communications with High Output Amplifier(Audio)

Posted on Jan 31, 2014

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 7 Answers

SOURCE: check engine light on harley softtail custo 07

try unhooking battery cable and rehook,it should reset. Hope this works for you.

Posted on Mar 13, 2009

Mitchy123

Mel Jacobson

  • 216 Answers

SOURCE: Check engine light comes on for about 10 secs. after starting

Its a self diagnostic,,,, the check engine light should stay on for a few seconds and then go out ....as long as it doesnt come back on ....u are A OK !

Posted on Apr 18, 2009

Anonymous

  • 1 Answer

SOURCE: Engine Check Light on

I disconnected the battery, pulled the maxi fuse and 15amp ecm fuse. I waited a while and put the fuses back in and connected the battery and it was cleared.

Posted on May 08, 2009

OneRide

Gar

  • 384 Answers

SOURCE: check engine light on

Not much you can do at home since the bike is a FI model. Get a HD tech to pull the trouble codes with a scanner. At least you will have a starting point to diagnose the problem.

Posted on Jun 04, 2009

OneRide

Gar

  • 384 Answers

SOURCE: 2006 883 801 miles check engine light, engine sputters,

You are going to have to pull the trouble codes out of the computer. If you can't do it yourself, a dealer can. This will give you a starting point to diagnose the problem.

Posted on Dec 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

5 Answers

Check engine light flashing, spuddering and rough


Have your codes read. Autozone does it for free. Only then will you have an idea of where to start looking.

Oct 26, 2011 | 2001 Kia Sportage

2 Answers

Check Engine light stays on. No other symptoms. If I reset the computer by disconnecting the battery, the check engine light eventually comes back on and stays on. Sometimes this takes weeks... sometimes...


you should have scan done for fault codes
but you could inspect the throttle body for carbon deposits and clean as required first and see how it goes

Jun 12, 2010 | 2000 Mazda MX-5 Miata

1 Answer

2001 Tahoe: Hard to start, idles rough, check engine light on.


Flashing check engine light is missfire, fuel pump probably causing multiple tries to start.Having to build fuel preasure,vac leak on one side of intake probably causing rich/lean condition.Also check back preasure to cat ,Sound like you are moving down right track.Mas air flow would probably set lean code bank1 and lean code bank2

Jun 19, 2009 | 2003 GMC Yukon XL

1 Answer

2000 Kia Spectra


http://www.kiatechinfo.com/index.asp

Good source for Kia its free to register NO STRINGS

May 16, 2009 | 2003 Kia Spectra

2 Answers

Malfuntion light coming on...egr valve may need replaced


the range from a simple sensor issue with no symptom except a check eng light to a rough idle with a light.

Mar 20, 2009 | 2005 Dodge Grand Caravan

2 Answers

2003 Silverado rough idle, idles good after "check engine" light


Check your o2 sensor voltage, those trucks are real bad for o2 sensors, and yes if one sensor is reading 0mv, the others will start to drop out, and the vehicle will run very, rough. You also may check fuel system pressure, should be almost 60p.s.i. If its alot lower, Id be looking into a fuel pump. If that vehicle is drive-by-wire (no throttle cable), the throttle bodies get very dirty and cause that concern also. Id start by having the vehicle scantested.

Feb 02, 2009 | 2003 Chevrolet Silverado Ss

3 Answers

95 cadillac eldorado engine stalls rough idle check engine light is on


I have a 1994 Cadillac Eldorado and every time i start it the car has rough Idle and the Idle fluctuate's. I also can feel it in the gas pedal when the car is doing this I tried replacing the throttle body sensor but it still does it I also was told it was the Idle error sensor. So instead of spending the unecessary money again I thought I would go online and see if anyone could help me with this problem.

Sep 30, 2008 | 1995 Cadillac Eldorado

2 Answers

Check engine light


Good Day,

The check engine light is part of the car's OBD(On-Board Diagnostic) system. The check engine light is turned on when a sensor becomes faulty or gets a false reading. Typically the check engine light will come on and stay on until the sensor that caused the fault is replaced. In your case you say it comes on while driving, so I am assuming when you first start the car the light is off. This would inicate that the faulty sensor is operational until it is heated up, then it is giving a fault. Have you noticed any thing strange while the light is on? As in lower gas mileage, running rough, running fast, low idle, high idle, overheating, anything at all that could help indicate what the cause maybe. Does the check engine light stay on until you park the car? If so you can have the "code" read from the OBD to pinpoint hte exact problem.


Hope this helps for now

Jul 07, 2008 | 1992 Mercury Grand Marquis

1 Answer

1995 mazda protege having problems running during aceleration


change the transmission fluid, replace the oil and oil filter check spark plug cables, check starter coilpak, and make sure there is coolant

Jul 02, 2008 | 1995 Mazda Protege

Not finding what you are looking for?
2007 Harley Davidson FXDB Dyna Street Bob Logo

794 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

6082 Answers

Mike

Level 3 Expert

4367 Answers

Marvin
Marvin

Level 3 Expert

85222 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...