Question about 2001 Yamaha V Star 1100 Classic
I own a 2002 Yamaha V-STAR 1100 Custom. I have had the bike for about one year. I have had to frequently replace the rear spark plug (monthly) since it seems to "foul" out due to "back-firing" The previous owner says he had no such problem.
I replaced the IGNITION COIL to the rear cylinder because I thought it was intermitantly functioning. The problem was not corrected.
I checked the settings on the DYNA 3000 ignition system and they all were set to the mid range setting as prescribed by the operational chart that came with the bike.
I emptied the fuel tank, dried it out and checked for foreign objects and found none. I replaced the in line fuel filter.The backfiring continued.
I removed the air box cleaned it and checked all the air fittings. The problem continued.
I contacted the dealer and was told that a thouough cleaning of the dual carburator should solve the problem. I removed the carb covers, the rubber diaframs, the needle valves, I soaked them in carb cleaner. I cleaned the exposed ports, covers, inlets, and other parts dried them and reassembled the system. Once again the backfiring continued.
I have gone as far as I can with the limited knowledge that I have. Can anyone guide me from here?
Thank you for any aide that you can render.
Does the bike backfire only when the throttle is being closed? The carbs have a idle enrichment circuit. If the idle enrichment diaphragms are stuck in the closed position, the bike will backfire when the throttle is shut down. You can't remove these parts for cleaning without seperating the two carb bodies (and then needing to synchronize the carbs after reassembly). A trick that worked for me...fresh fuel, and some fuel system cleaner in the tank...ride the bike at highway speeds for 20 -30 minutes...repetedly rev the engine to a high RPM then shut the throttle closed. The repeted application of high engine vaccum to the enrichment diaphragms freed the stuck diaphragms and the fresh fuel cleaned any gum and varnish that caused the trouble. I've put 20,000 miles on it since then with no backfiring.
Posted on Jun 16, 2009
Sometimes what sounds like "backfiring" is actually fuel igniting in the exhaust. This typically happens with after market pipes or slip on's. The carbs come very lean from the factory and so the PMS (pilot mixture screw) needs adjusting more to the richer side. If they have not been adjusted they are still hiding underneath brass plugs on the underside of the carb by the float bowl. Carefully drill them out and adjust them out a little at a time. Mine are out at least 4 turns to get this popping to stop. Also your carbs will need syncing after this procedure. A DIY tool is easily built for under $5 if you do a google search. Go here for more information. http://www.sloneservices.com/SilverBack/VStar1100-FAQ.htm
Posted on Jun 15, 2009
Have you double checked the timing?
Posted on May 27, 2009
What type of plugs are you using? The manual says to use NGK BPR-7ES, but these aren't usually available except at Yamaha motorcycle shops. You can use the more widely available BR-7ES, but not BP-7ES, the timing will be off at higher RPM. "R" stands for resistor which slightly delays the timing and produces a more powerful spark. "P" is a projected tip, a couple mm further into the engine.
My other suggestion is to go back to the stock ignition. I had similar problems with my first Dyna 3000 unit which I returned, then the replacement unit worked but the engine just didn't spark as hard as it does with the stock ignition. Although it can't be tuned, the VStar motor runs far better with a stock ignition.
Posted on Nov 05, 2014
The 1100 Vstar (not sure what the 600 has) comes with an a.i.s. that can cause this problem. This is an emissions control system that allows air to be drawn into the exhaust downstream of the cylinder head to ignite unburnt fuel vapor. This may cause some popping or backfiring, especially on deceleration. It's not a problem with stock exhaust, but I will be presumptuous here and assume you went to an after-market exhaust. (or removed the baffles from the stock exhaust) If this is the case you will need to disconnect the emissions system and toss it. Should solve your problem. I was fouling plugs and running rough etc. until I removed this device. Here is a link to more info regarding the emissions system and problems it causes: http://www.vstar1100.com/jack_phelps/vstar/ais.htm
Posted on Jul 18, 2010
I had this problem on my suziki intruder 1400 only running on one cylinder i put some fresh gas and throttle it rode off and they both kicked in .............runs good now
Posted on Sep 08, 2009
Check for exhaust leaks, a friend had same problem, found and welded small split in exhaust pipe
hope it helps
Posted on May 29, 2009
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Tips for a great answer:
Jul 20, 2012 | 1999 Yamaha V Star 1100 Custom
Nov 24, 2017 | 2002 Yamaha V Star 1100 Custom
Feb 20, 2012 | 2002 Yamaha V Star 1100 Custom
Jun 01, 2011 | 2001 Yamaha V Star 1100 Classic
Apr 22, 2011 | 2006 Yamaha V Star 1100 Classic
Oct 04, 2010 | 2002 Yamaha V Star 1100 Custom
Aug 03, 2010 | 2002 Yamaha V Star Classic
Jul 12, 2009 | 2006 Yamaha V Star 1100 Custom
9,931 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: