Question about Yamaha RD 350 Motorcycles

1 Answer

Yamaha warrior is stuck in 3rd gear nad rear end is locked up and there is play in the shift lever but wont click into any gear

Iv fixed atvs before but i have nvr ran into this pronlem i just bought the wheeler today and the clutch lever moves freely but the gear shifter has play and wont click into gear and the rear tires wont move even when i rock it back and forth i really need help

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Yamaha Master
  • 1,190 Answers

Sounds like gear box needs stripping and check allcogs and selecter forks etc for wear or damage! happened to me on a yamaha rd 200 ! P...

Posted on Jan 03, 2014

Ad

4 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

tombones

  • 3567 Answers

SOURCE: will not shift into 5th while underway.

You have a bent shift fork not engaging the slider gear fully into 5th gear. The engine will need to come out of the bike. Remove the top end, the flywheel and electrics, the clutch, shift mechanism and kick starter and a few other parts. THEN you are ready to split the gearbox to get to the crankshaft, gears and shift forks.


You will need an impact driver, flywheel puller, case splitter, torque wrench and factory service manual, plus the normal screwdriver, pliers, etc.. Alternate to the special tools is taking it to the dealer and say "Fix it". I normally tell people to take it to the shop just so they don't get into such an involved project and they have a knowing eye working on the engine.

Please rate this solution. Thanks

Posted on Aug 17, 2009

tombones

  • 3567 Answers

SOURCE: Honda ST1100, I have difficulty shifting down

You have a couple of bent shift forks. Major work to replace the forks. Time for the Honda dealer to get involved. Sorry.

Please rate this answer. Thanks!

Posted on Apr 02, 2009

tbrat44

  • 86 Answers

SOURCE: The trans is stuck in 3rd gear. wont shift

sounds like the shift lever shaft broke internally. if you know enough to take it apart and repair yourself, you will firure out how the gearing works. also check shifting forks for defects, make certain thier not bent or this problem will happen again.

Posted on May 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stuck in gear


I'd go to the junction of the linkage and the transmission and check from there. The transmission will have a lever or some sort of protrusion connecting to the linkage. See if you can move the lever/protrusion by hand, even if you have to disconnect it from the linkage. If you can move it, try to find neutral and reattach the linkage and adjust it so it corrresponds to the indicator on the shifter. If you can't move the lever/protrusion it's internal to the transmission and you are out of luck unless you're up to cracking open the transmission.

May 10, 2014 | Yard Machines 155 Torque Briggs Stratton...

1 Answer

My 99 Cougars manual transmission will not go into any gears at all


Check the cable under the gear lever. Look for broken pin or missing pin joining the lever to the cable

Mar 05, 2013 | 1999 Mercury Cougar

1 Answer

What makes up the governor assembly in a Chrysler 300M


All the parts you listed are internal to the transmission. The cable is external - it runs from the shifter lever to the range selector lever on the transmission. Their analysis doesn't sound right though. If the cable is broken, the shifter should move freely as you described. But that (broken cable and bent lever) happened AFTER the problem of the transmission being stuck in reverse. Your efforts to unstick probably bent the shifter and broke the cable. It would seem something was jammed before you tried to get out of reverse, possibly inside the transmission.

Mar 09, 2017 | 2001 Chrysler 300M

1 Answer

2003 FJR 1300 clutch adjustment


Hi, Darrell_kauf and the usual suspects are:
1. Clutch not adjusted properly.
2. Primary chaincase overfilled with lubricant.
3. Corners wore off shifter clutch dogs.
4. Shifter return spring bent or broken.
5. Bent shifter rod.
6. A loose shift lever on shifter shaft.
7. Shifter forks sprung.
8. Shifter pawl needs adjusting.
9. Heel/toe shifter coming in contact with the floorboard.
10. Transmission oil too heavy.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Clutch Adjustment Technical Mechanical Problems
How to do clutch soak or replacement on Yamaha FJR 1300cc Second generation
Yamaha 2003 FJR1300 Service Manual
OEM parts for Yamaha
Yamaha FJR1300A Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


Feb 08, 2011 | 2003 Yamaha FJR 1300

1 Answer

Ran fine yesterday, but now kick start spin freely


Broken return spring is my guess or it has come off the holding post.

Feb 23, 2010 | RTO Quads 125cc Full Size Adult 4 Wheelers...

4 Answers

Deore dx shifter stops working


had the same problem, didn't use my bike for longer period. open the shift lever carefully and try something like caramba. worked for me.
sebastian

Sep 07, 2009 | Shimano Deore Xt Thumb Shifters 7...

1 Answer

1995 hanoda 125 three wheeler will not change gears stuck and can not get it out of gear - is there an adjustment or a online manual that i can read to fix the problem - thanks


make sure the clutch cable is properly adjusted, next thing would be to check if your clutch itself is in good condition and adjusted. to test, pull clutch lever in (with bike off) place it in gear, bike should move freely when pushed forward.. if that is all well and doesnt work good, you need transmision repairs,shifting forks probably bent.

Jul 10, 2009 | 1985 Honda XL 125 R

1 Answer

Clutch


Clutch plates wiuld affect all gears.The type of oil in the enine affects the plates. .Make sure you the clutch is not hanging up and has free play on lever when clutch is engaged. It should be slipping bad. ckeck clutch lever on yhe engine for full release and free play.. good luck

May 22, 2009 | 2004 Honda CBF 250

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

745 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1176 Answers

Paul Ellermets

Level 1 Expert

6 Answers

Neil Lancaster
Neil Lancaster

Level 1 Expert

14 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...