I need a diagram showing me how to do the wiring to change handlebars...I am replacing the old ones but can't understand how to do the wiring through them......PLEASE HE:P
Hi, Capricorn39 for this scenario you will need your service manual that has all fastener torque specs -fluid capacities and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at [email protected]. Good luck and have a wonderful day.
https://www.google.com/search?sxsrf=ALeKk019Tg4MHOKCmw75rlAx6VRcJF7iLA:1615198589847&source=univ&tbm=isch&q=2001+HARLEY+DAVIDSON+DYNA+WIDE+GLIDE+WIRING+DIAGRAM+@&sa=X&ved=2ahUKEwiWxMHRu6DvAhXXF1kFHYKsAn0QjJkEegQIBBAB&biw=1440&bih=757
http://www.mediafire.com/file/g3h2vn0nvw3b5wb/2001_Harley_Dyna_Service_Manual.pdf/file
https://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://serviceinfo.harley-davidson.com/sip/service/document/6300
https://www.6ya.com/how-6ya-works to speak to me personally.
SOURCE: replace handle bars
Mine had wiring inside the bars as well. Basically I removed the controls from the bars, and removed the 2 bolts holding the handle bars on. I removed the RIGHT side gas tank after draining it. I intended on cutting the wires to the connectors, pulling the wires out of the old handle bars, and pulling them back through the new bars. Note: Mark the black wires very carefully, since there were 5 black wires in the two connectors and they are all unique wires. The colored wires were easy, just match them back up. Several tricks I found on line. Use a string and a bolt to fish a pull line down through the new bars then pull the wire bundle through. This worked great on both left and right wire bundles. I then bolted the new handle bars in place and remounted the controls. I then replaced the shrink tubing up the bundles that hid the actual wires as they came out of the handle bars down to where I cut the connector wires, behind the right side tank. Next I stripped and tinned all the wires I cut (twist and get a little solder to stick on the wires) and stuck little pieces of shrink tubing up or down the wire so after I resoldered the wire I could shrink the insulation back over the splice. I picked up the shrink tubing and some extra wire a home depot. I had a soldering iron, and heat gun so away I went connecting the dots again. Litte tedious but hey. It saved me somewhere between $500 -$700 bucks which is what the harley shop quoted before I started. I tested each function, then reinstalled the gas tank and tightened up all the stuff. Below is the pin out in case you do loose a wire marker, like I did. Good Luck.
SOURCE: replace handle bars
Mine had wiring inside the bars as well. Basically I removed the controls from the bars, and removed the 2 bolts holding the handle bars on. I removed the RIGHT side gas tank after draining it. I intended on cutting the wires to the connectors, pulling the wires out of the old handle bars, and pulling them back through the new bars. Note: Mark the black wires very carefully, since there were 5 black wires in the two connectors and they are all unique wires. The colored wires were easy, just match them back up. Several tricks I found on line. Use a string and a bolt to fish a pull line down through the new bars then pull the wire bundle through. This worked great on both left and right wire bundles. I then bolted the new handle bars in place and remounted the controls. I then replaced the shrink tubing up the bundles that hid the actual wires as they came out of the handle bars down to where I cut the connector wires, behind the right side tank. Next I stripped and tinned all the wires I cut (twist and get a little solder to stick on the wires) and stuck little pieces of shrink tubing up or down the wire so after I resoldered the wire I could shrink the insulation back over the splice. I picked up the shrink tubing and some extra wire a home depot. I had a soldering iron, and heat gun so away I went connecting the dots again. Litte tedious but hey. It saved me somewhere between $500 -$700 bucks which is what the harley shop quoted before I started. I tested each function, then reinstalled the gas tank and tightened up all the stuff. Below is the pin out in case you do loose a wire marker, like I did. Good Luck.
SOURCE: oil drain plug 2004 harley dyna wide glide
your oil drain is on the right side pipe side of your bike look under near the rear back part of your frame you will see a plug with a one quarter allen key threaded plug style bolt kinda hidden in bridge plate of frame it is flat in conjuction with line on bike it is in area right behind where your back pipe expands to baffle of pipe where its skinny and then gets bigger its the one closest to you
SOURCE: will a gas tank off a 5 harley dyna wide glide
It sure will!! You answered your own question. guess i get no points for this one.
SOURCE: 2006 HARLEY DAVIDSON DYNA WIDE GLIDE HAS A MISS IN
This is a possability but it does not happen as often as most would like to say. A quick check would be to run the engine to operating temp the take WD40 lube spray and spray it directly at the seals on the heads. If it is an intake leak your motor will change its idle. It will either speed up or miss. This is an indication of an intake leak.
1,070 views
Usually answered in minutes!
×