Need to the torque specs for a 1999 Dodge Durango

Lower Intake:

1. Use a skin coat of RTV silicone on both sides of the water passage ports (outer most holes) and put the new lower intake gaskets into place
2. Hand tighten the 13mm head intake bolts and Torque the bolts , starting from the center and working your way out in a circular pattern
3. Torque these bolts in a few small increments until they have reached 250 inch pounds of torque.
4. Upper Intake Plenum:
5. When installing the intake air plenum , be sure to catch the four center bolts and the two side bolts (stiffener brackets) before tightening , The center bolts should be torqued to 250 inch pounds .The fuel rail bolts should be torqued to 100 inch pounds

Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:

1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
2. Step 2: Bolts 1-10 verify torque without loosening
3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)

Cylinder Head Bolts (First Pass all M11 Bolts in Sequence)
30 N?·m
22 lb ft
Cylinder Head Bolts (Second Pass all M11 Bolts in Sequence)
90 degrees
Cylinder Head Bolts (Final Pass all M11 Bolts in Sequence-Excluding the Medium Length Bolts at the Front and Rear of Each Cylinder Head)
90 degrees
Cylinder Head Bolts (Final Pass M11 Medium Length Bolts at the Front and Rear of Each Cylinder Head in Sequence)
50 degrees
Cylinder Head Bolts (M8 Inner Bolts in Sequence)
30 N?·m
22 lb ft
Intake Manifold Bolts (First Pass in Sequence)
5 N?·m
44 lb in
Intake Manifold Bolts (Final Pass in Sequence)
10 N?·m
89 lb in
Intake Manifold Wiring Harness Stud
10 N?·m
89 lb in

1. 2.7 litre intake bolt torque spec in a 2008 dodge charger ...

   www.fixya.com/cars/t18664111-2_7_litre_intake_bolt_torque_spec_in Jun 27, 2013 - Head Bolts Step one 37 ft lbs then tignten 120 degrees more. Rocker arms. Step one 11 ft lbs then tighten 90 degresss more. Upper intake 89 inch ...

Need the tork for the head

Cylinder Head Bolt Step1- (25 FT.Lbs) Step2(45 Ft.Lbs) Step3(65Ft,Lbs).....Intake Manifold(35Ft Lbs)....Exhaust Manifold Center (20Ft Lbs) All Others (20 Ftlbs).....Thanks

I have the specs and diagrams. If you want me to send them to you, give me your email address. [email protected]

Here's a link to a conversion calculator,www.unitconversion.org/energy/inch-pounds-to-foot-pounds-conversion.html

I googled the specs and i found mine it will give numbers and pictures. Sorry i couldn't actuall y give u the answer.

Cylinder Head Bolt (Preferred Method) All Bolts First Pass in Sequence 22 ft.lb Long Bolt Final Pass in Sequence 75 deg. Medium Bolt Final Pass in Sequence 65 deg Short Bolt Final Pass in Sequence 55 deg. Cylinder Head Bolt (Optional On-Vehicle Strategy) First Pass in Sequence 26 ft.lb Second Pass in Sequence 44 ft.lb Final Pass in Sequence 66 ft.lb