2009 Yamaha Roadliner Midnight Logo

Related Topics:

Shawn Bristle
Shawn Bristle Posted on Mar 11, 2012
Be the first to answer

How do I disassemble the headlight housing on my 2009 Yamaha Roadliner?

The arm of the front turn signal light is mounted to the headlight assembly. It is loose, but I need to open the headlight housing to get to it. I'm not sure where to start, and I don't have a repair manual.

Answer This Question

5 Related Answers

Anonymous

  • 301 Answers
  • Posted on Oct 14, 2009

SOURCE: how do you adj this cutch it just started sliping

The clutch on the Roadliner is Hydraulic. I am pretty sure it is not adjustable. Make sure you are running the proper oil in the engine. Car oil can make the clutch slip and if it is slipping it may need to be replaced.

I am also a Roadliner owner.

Ad

Anonymous

  • 1 Answer
  • Posted on Nov 17, 2009

SOURCE: Setting the clock on a 2006 Yamaha Roadliner

the clock is set by holding the button down on the clutch side of the handlebars until your display blinks. The you use the front brake side to adjust the time.

Anonymous

  • 7 Answers
  • Posted on Jun 03, 2010

SOURCE: What does the switch with the headlight do on the

If you decide to add the passing lamps to your bike later on, that switch cuts them off and on.

Anonymous

  • 632 Answers
  • Posted on Jul 06, 2010

SOURCE: Yamaha YZ426 not starting after head gasket repair

This could be a compression problem, Try Removing spark plug and use a compression gauge

You may not have sealed the head proper and bike is lacking in compression..

heimlich

David Belcher

  • 1978 Answers
  • Posted on Apr 14, 2011

SOURCE: On the 2009 Yamaha Raider

The two prong capped plug end is inside the headlight housing. It will have a blue(or brown) and a black wire. Black is ground. Blue(or brown) is 12V+ when the bike is running and the switch is turned on. These two wires terminate at a plug under the tank on top of the airbox (under the ECM). You can tie into the lines in the headlight or tie in at the plug.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Replace headlight assembly 1996 Yamaha XVZ1300.

Yamaha XVZ1300 Royal Star Motorcycle Lighting ' Headlights ...

 https://www.motorcycleid.com > ... > Lighting > Yamaha
Find the right Motorcycle lighting products for your Yamaha XVZ1300 Royal Star in our inventory. ... 2009; 2008; 2007; 2006; 2005; 2004; 2003; 2002; 2001; 2000; 1999; 1998; 1997; 1996 ... Show Chrome® - LED Turn Signal Light Upgrade Kit.

Replacing The Headlight Bulb - Yamaha Royal Star Venture ...

 https://www.manualslib.com > ... > Owner's manual
Yamaha Royal Star Venture XVZ13TFX Manual Online: Replacing The Headlight Bulb. This model is equipped with a quartz bulb headlight. If the headlight bulb ...

Motorcycle Parts Yamaha Royal Star - Amazon.com

 https://www.amazon.com > Motorcycle-Parts-Yamaha-...
Results 1 - 48 of 828 - 1996-2001 YAMAHA ROYAL STAR UNI MOTORCYCLE AIR FILTER ... Z-OFFROAD Upgrade 7 Inch LED Headlight + 4.5 Inch Fog Passing ...
Read full answer
Jun 02, 2021 • 1996 Yamaha Royal Star XVZ 1300 A
0answers

My front turn signal assembly on my 2007 Yamaha Stratoliner has come loose. How do I tighten it?
Read full answer
Be the first to answer Jan 13, 2013 • 2007 Yamaha Stratoliner S
0helpful
1answer

How do you remove the headlight assembly on 1995 ford f250?

  • 1.
    Remove the two upper screws from the headlight housing, using a Phillips screwdriver.
  • .
    Locate the two lower retaining nuts inside the engine compartment at the bottom of the headlight housing. Remove the nuts using a ratchet, extension and socket.
  • Separate the turn signal and marker light assembly from the front grill. Rotate the bulb holders counterclockwise and pull them out of the assembly. Set the assembly aside.
  • Unplug the headlight bulb connector from the bulb. Rotate the retaining ring counterclockwise one-eighth turn and remove it from the housing. Pull the headlight bulb straight back and out of the housing. Do not rotate the bulb during disassembly.
  • Lift up on the headlight housing retaining clips to unsnap them from the headlight housing vertical adjuster studs.
  • Locate the horizontal adjuster at the outer bottom corner of the headlight assembly inside the engine compartment. Loosen the horizontal adjuster until it is free of the adjuster nut.
  • Remove the headlight housing from the vehicle.
Installation
  • Install the headlight housing in the front grill.
  • Engage the horizontal adjuster screw with the adjuster nut and screw it partially in.
  • Snap the headlight housing clips on the vertical headlight adjuster studs.
  • Insert the headlight bulb into the headlight housing, flat side up. Slightly rotate the headlight bulb to engage the grooves in the light with the alignment tabs in the back of the housing. Install the retaining ring on the bulb. Plug in the headlight bulb connector.
  • Install the bulb holders in the turn signal and marker light assembly. Install the assembly in the grill. Install the two upper screws, using a Phillips screwdriver. Install the two lower retaining nuts, using a ratchet, extension and socket.
Headlight Aiming
  • Pull the vehicle to within a few inches of a blank wall, on a flat surface. Apply two strips of tape to the wall vertically to mark the centers of the headlights. Apply a strip of tape to the wall horizontally to mark the center of the headlight height. Back the vehicle up 25 feet in a straight line.
  • Turn the headlight low beams to the "On" position.
  • Adjust the vertical headlight adjusters until the high-intensity zone of the light pattern is two inches below the horizontal mark on the wall.
  • Adjust the horizontal headlight adjusters until the high-intensity zone of the light pattern is two inches to the right of the vertical headlight marks on the wall.
Read full answer
Nov 08, 2012 • Cars & Trucks
0answers

How to turn on the hazard lights on a 2009 roadliner s 1900
Read full answer
Be the first to answer Sep 11, 2011 • 2009 Yamaha XV1900A Midnight Star
0answers

My front turn signal assembly on my 2007 Yamaha Stratoliner has come loose. How do I tighten it?
Read full answer
Be the first to answer Mar 17, 2011 • 2007 Yamaha Stratoliner S
1helpful
2answers

How do you remove the headlights off a Pontiac grand am 2004
Lighting Headlight, Side Marker, Park & Turn Signal Assembly Removal & Installation To Remove:
  1. Open the hood.
  2. Remove the front air deflector.
  3. Apply light pressure to the headlight lens to hold the headlight in place while disconnecting the retainers.
  4. Lift up the headlight retainers to release the housing.
  5. Remove the headlight assembly, pulling straight forward from the headlight mounting panel. NOTE: Note the location and position of the adjuster retainers and locator tab.
  6. Disconnect the wiring harness from the headlight assembly.
  7. Rotate the bulb(s)/socket(s) as needed counterclockwise to release.
  8. Remove the bulb(s)/socket(s) from the headlight assembly.
To Install:
  1. Install the replacement bulb(s)/socket(s) to the headlight assembly rotating clockwise until fully seated.
  2. Connect the wiring harness to the headlight assembly.
  3. Position the headlight assembly to the mounting panel.
  4. Apply light pressure to the headlight assembly lens to hold the assembly in place while installing the retainers.
  5. Align the headlight assembly retainers and slide them over the assembly mounting tabs
  6. Install the front air deflector.
  7. Close the hood.
prev.gif next.gif
Read full answer
Feb 02, 2011 • 2004 Pontiac Grand Am
0helpful
1answer

Removing and reinstalling a new headlight assembly in a 95 jeep grand cheerokee
LIGHTING Headlights REMOVAL & INSTALLATION Cherokee, Wagoneer and Comanche Models Fig. 1: Remove the top corner headlight bezel mounting screw 91076p12.jpg
Fig. 2: To access the turn signal bulb or headlight bezel mounting screws, remove the 2 turn signal housing retaining screws 91076p13.jpg
Fig. 3: After removing the turn signal housing from the headlight bezel, remove the 2 bezel mounting screws . . . 91076p27.jpg
Fig. 4: . . . then carefully pull the headlight bezel away from the headlight assembly 91076p11.jpg
Fig. 5: Remove the 4 headlight assembly retaining ring screws . . . 91076p07.jpg
Fig. 6: . . . then pull the retaining ring off of the headlight assembly 91076p06.jpg
Fig. 7: Pull the headlight assembly away from the vehicle just far enough to disengage the electrical connector from behind the headlight 91076p28.jpg
  1. Remove the headlamp bezel and retaining ring attaching screws. Remove the bezel and retaining ring.
  2. Pull the headlight out, disconnect the wire harness and remove the headlight from the vehicle.
  3. Install the headlight in the reverse order of removal.
Grand Cherokee and Grand Wagoneer Models
  1. Open the hood, reach into the engine compartment and locate the lock ring supporting the bulb assembly.
  2. Rotate the lock ring 1?8 turn counterclockwise and pull the bulb straight out from the housing. To install:
  3. Install a new bulb and position the bulb assembly in the lamp housing.
  4. Rotate the lock ring 1?8 turn clockwise to secure.
----
The Grand Cherokee will have an assembly that is fastened with bolts and screws to the body.
Get the new assembly and compare to the old one to see where to unfasten the bolts and other fasteners to aid in removing quickly.

Read full answer
Oct 08, 2010 • 1995 Jeep Grand Cherokee
0helpful
1answer

How to replace front turn signal housing
Front Turn Signal & Parking Lights
  1. On some models you will need to remove the headlight bezel mounting screws and the bezel.
  2. Remove the mounting screws for the lamp assembly.

af50756.gif
Remove the mounting screws securing the lamp assembly

  1. After the screws are removed, pull the assembly from the vehicle.

5deda5d.gif
After the screws are removed, pull the assembly from the vehicle

  1. Disconnect the twist lock socket from the lens housing.

90fe451.gif
Disconnect the twist lock socket from the lens housing

To remove the bulb, turn the twist lock socket (at the rear of the housing) counterclockwise 1/4 turn, then remove the socket with the bulb; replace the bulb if defective.


0568896.gif
Newer Oldsmobile models have the turn signal separate from the headlamp assembly ...


252443f.gif
... unlike the newer Buicks, where the unit is attached to the headlamp

To install:
  1. Install the electrical harness to the back of the unit.
  2. Position the signal assembly, then attach to the vehicle with the mounting screws. Tighten the screws to 54 inch lbs. (6 Nm).
  3. Insert the socket to the back of the unit, then attach the headlamp bezel if removed.
Read full answer
Feb 13, 2010 • 1992 Oldsmobile Cutlass Ciera
0helpful
1answer

Change front turn signal light?
Front Turn Signal & Parking Lights
  1. On some models you will need to remove the headlight bezel mounting screws and the bezel.
  2. Remove the mounting screws for the lamp assembly.
c289083.gif
Remove the mounting screws securing the lamp assembly

8325b44.gif
After the screws are removed, pull the assembly from the vehicle

ad45385.gif
Disconnect the twist lock socket from the lens housing
To remove the bulb, turn the twist lock socket (at the rear of the housing) counterclockwise 1/4 turn, then remove the socket with the bulb; replace the bulb if defective.

19af8c1.gif

Newer Oldsmobile models have the turn signal separate from the headlamp assembly ...

d57d520.gif
... unlike the newer Buicks, where the unit is attached to the headlamp

To install:
  1. Install the electrical harness to the back of the unit.
  2. Position the signal assembly, then attach to the vehicle with the mounting screws. Tighten the screws to 54 inch lbs. (6 Nm).
  3. Insert the socket to the back of the unit, then attach the headlamp bezel if removed.
Read full answer
Oct 31, 2009 • 1990 Pontiac 6000
2helpful
1answer

How do i install a new front turn signal bulb on my 2000 pontiac montana
You have to remove the headlight assembly to remove the turn light assemble. There are two mounting bolts that hold the headlight assembly to the frame that needs to be removed and one mounting bolt that holds the turn signal light assembly on the headlight assembly that needs to be removed. Once all three bolts (black plastic in colour with a wing nut) have been removed the headlight and turn signal assembly can just be removed. Take note that the assembly has a guild slot to be guild in place back when re installing the head light and turn signal assembly. Good luck and hope this helps. Keep me posted and I'll try to explain in a different way if i was un clear, Harder to explain then doing the job it self. 
Read full answer
Jul 20, 2009 • 2000 Pontiac Montana
Not finding what you are looking for?

View Most Popular

2009 Roadliner Midnight

  • Motorcycles

Related Question

Replace headlight assembly 1996 Yamaha XVZ1300.

  • 1996 Yamaha Royal Star XVZ 1300 A

Related Topics

312 views

Ask a Question

Usually answered in minutes!

Popular Questions

I HAVE A 06 ROADLINER 1900 FIRST OIL CHANGE I USED

2006 Yamaha Roadliner Midnight

Fuel gauge stuck

2009 Yamaha Roadliner Midnight

2006 yamaha roadliner 1900 rattle under gas tank

2006 Yamaha Roadliner Midnight

Yamaha Star Roadliner S?

2006 Yamaha Roadliner Midnight

Speedometer

2009 Yamaha Roadliner Midnight

Top Yamaha Experts

vince

Level 3 Expert

2530 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1212 Answers

littlewheel

Level 2 Expert

122 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...