Question about Qianjiang Motorcycles

Open Question

I replaced stater, coil, cdi box, and others... if i disconect the green wire to coil it will shock me a little but not enough .conect it back nothing.

I need to know how to bypass and check one thing at a time.willing to pay.already spent 250.00 at three different shops. FRUSTRATED!

Posted by on

Ad

6 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 7 Answers

SOURCE: no spark

It sounds to me like the repair shop has connected the ignition wire ( the wire going to the + side of the coil ) to the wrong switch terminal. Take a volt ohm meter and connect the ground wire to the negitive ( - ) side of the battery and expose the ignition switch terminals. With the switch in the OFF position check for volatge on all the terminals. Make note of any terminals showing a 12 volt reading. That is probably the feed line from your battery. Turn the switch to the ON or RUN position and check for a terminal other than the one which gave you a reading before. note and mark this terminal. Locate the coil. There are 2 thin ( 18 guage ) wires attached to the coil. One goes to the distributer and the other goes to the ignition switch. Isolate that wire and reattach it to the connection on the ignition switch you marked earlier...
Good luck,
shag79

Posted on Nov 29, 2008

Ad
crapiemael

Crap Iemael

  • 241 Answers

SOURCE: Kawasaki Ninja 1000RX ´86

Probably a gas delivery problem to the carbs. Check the lines and check for a filter in the line or at the carbs. Something is stopped up and it can't get enough gas to go any rpms.

Posted on May 22, 2009

Anonymous

  • 957 Answers

SOURCE: TTR 90 wont start. Not carb. Not CDI. Plug cap?

Every component plays a part in the ignition system. Check the wiring as you go. Start at one end and move forward. You have done a lot of work so far. so you should be close. If the igniter is fine and the other components too. Then it would narrow it down to an electrical problem or no signal/pulse to the coil. See if the coil is receiving that pulse. you can use a test light for this test. Pos. will be power and NEG. will be the pulse. With light on the NEG. crank the engine over and see if it flashes. Let me know how its going.

Posted on Jun 01, 2009

Anonymous

  • 125 Answers

SOURCE: 1987 Honda shadow vt1100c no spark at any plug

The voltage on the coils is present except at the instant of firing. The interruption of the voltage is what causes the coil to fire. The cdi box is what causes the voltage interruption.
The interruption is very hard to detect. You are not the first to be stymied by that box. If you have access to an oscilloscope, I think you can see the pulse if it occurs.

Posted on Jun 15, 2009

tombones

  • 3567 Answers

SOURCE: No spark

Check the side stand kill switch if your bike has one. It kills the engine so that you don’t start out with the side stand down. If broken or out of adjustment, it would kill the spark. Check for a broken wire at the side stand switch and coupler. Try moving the kill switch by hand. If that doesn’t work then wire a jumper around the switch to bypass it. Check the fuses. How good is the battery? Try a jump start from your car battery. Is the handlebar kill switch on? Check the operation of the ignition switch and all kill switches with a volt ohmmeter. Install new spark plug.

If that doesn't do it, check the wiring harness. Did a wire come unplugged? Are all wires clean and with solid connections? Any abraded or pinched wires? Is the bike in neutral and the neutral light is lit up? If no neutral light, check the neutral switch and neutral switch wire on center casing. If still no spark, get CDI system and coils checked at the dealers shop. You can screw up a CDI unit checking it yourself.

Posted on Jun 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Why does my 1999 chrysler sebring convertible JXi with amp under pass front seat, all speakers work except for the 2 front door speakers and the speakers are not the problem, they work fine everywhere


Most likely the amp. Manufacturers just don't seem to put these in spots that are dry. Behind the kick panel on the passenger side, this is where most water comes in. Under the seat, because water sits in/on the floor board it causes very high humidity. the other is in the truck, which also leaks and stores high humidity. And of course, they don't make them weather/water proof because the amp is inside the car. Thing is, you can't bypass the amp. The radio needs it to run the speakers. No amp, No sound. Your three options are, 1 replace the amp to get the door speakers. 2 repair the amp. 3 replace the radio and still have to bypass the amp. The speaker wires run from the radio to the amp from the amp to the speakers. So you will have to splice in a new radio, and splice the speakers wires at the amp. Hope this helps.

Jan 12, 2015 | Chrysler Cars & Trucks

1 Answer

Since I bought my ford expedtion 2005 in Janaury, it has displayed Tire Pressure Monitor Fault. All electrical has been replaced, tires have been changed, and the vehicle has been in 6 times for this, They...


You may want to forget the dealer, and we all want to know the answers, to why dealers fail to repair things.
A local shop should be able to reset the TPMS (Tire Pressure Monitor System) now you rotated the tires.
A dealer should,as any good shop, should be able to call up a diagnostic chart of your vehicle,IF, they subscribe to a Data Base,and they absolutely have to,or they have no info on your veh.
Now you need to pay for time spent, finding the cause of the issue.

Aug 23, 2010 | 2005 Ford Expedition

2 Answers

Have a Cub Recon 60" with Kohler 25. After the mower warms up it will struggle or not turn right even at a gentle turn. Left rear pump wines to the point i can hear it threw my ear plugs. Mower is under...


I have the exact same problem that just started today. I am going to call the repair place now but if you hear anything let me know @ bobbyrn@verizon.net There is an inline filter for the hydraulics under the seat. I hope that is all it is. its about 30$.

Apr 28, 2010 | Cub Cadet Street Sign- tractor lawn riding...

1 Answer

MOffice Pro 2007 activated too many times, how to i bypass this. I have it on all my PC's but can't use it on the new one


When you buy MSoffice you have an agreement that you'll only activate it so many times, it's different depending on how much you pay. You've already activated it the number of times you paid for, therefore you can't 'bypass' it without breaking copyright. However you might want to check out Microsofts Volume Licencing page for info about renewing:
http://www.microsoft.com/licensing/mla/trainer.aspx

Dec 21, 2009 | Microsoft Office Professional 2007 Full...

1 Answer

Have an RCA 60" rear projection tv (Model: P60752EB, Chassis: PTK169PEC). TV will not turn on. While pressing the power button it will make a clicking noise. Otherwise, there is no picture or sound. Have...


It is the 169 chassis-over 300 different models used it and are different-answer something for me--does it have a GREEN power light that comes on for a second and goes off?

I know this set well and to be honest hated working on them--Let me know about the power light and I will tell you what I know.

At one point in time this was a very good set--I do understand about paying a lot to get it fixed and having it bad again.

I am here to help people and I bet I know more about this set than almost anyone else here.

SD TECH

Dec 14, 2009 | RCA P60921 60" Rear Projection Television

1 Answer

I have a Simplicity S24 canister vacuum. It's about 3 yrs. old. In the past year I have had it in the shop 4 times because when using the rug piece, the piece turns on & off, on & off. The actual...


repair shop has not fixed the problem? complain until they fix it properly. This is a pressure fault / jamming issue or slipping drive. Repair shop should have fixed it 1st time.

Sep 13, 2009 | Vacuums

3 Answers

My car won't start. It is a '92. The instruments


sounds like the starter motor solenoid is defective replace it or the whole starter

Jul 27, 2009 | 1992 Geo Tracker

1 Answer

Hi i have a gt 1996 twin turbo every time i accelerate hard in 3 gear 4,8rpm it goes into limp mode im on standerd boost and dont know what to do/look for pls help?


This can be caused by many different things, it could be the transmisson or it could be the engine, if the oil level is low that could cause it, also if the oil is dirty or the oil filter is bypassing, So it really needs to be checked by a mechanic becasue it has to do withthe engine control system there is no way except to hook up a diagnostic tool and read all codes and read boost and driveability problems. It could be something simple but pay the $75.00 for the hook up fee and they can tell you whats wrong. And if the check engine light is a red check engine do not drive it to it to a shop.

Jul 08, 2009 | 1996 Subaru Legacy

1 Answer

Tv turns on for 1 sec then shute off power light blinks 3 times panasonic pt53wx53g projection


Hi 3 blinks on panasonic is the conversion ics. very common repair for projectors. you need to replace two ics on mother board. The cost of the repair from a tv shop is 250,00.

At least now you Dont have to pay a service center to come out and diagnose
Just give them your model number and they can look up the parts. The job take 1 hour to do or so.

I hope this help thanks doctor video leadingedgeelectronics 1987

May 04, 2008 | Televison & Video

2 Answers

Bypassing the parking brake feature


just earth the handbrake cable (light green) on a good earth point.

May 01, 2007 | JVC KD-AVX1 Car DVD Player

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Qianjiang Experts

Sumeet Sodhi

Level 2 Expert

163 Answers

Tom Diffin

Level 2 Expert

95 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6151 Answers

Are you a Qianjiang Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...