20 Most Recent 2007 Yamaha V Star Classic Questions & Answers


Hi, Kyle and the usual suspects are:
1. Clutch not engaging due to improper adjustment.
2. Clutch plates worn passed book specs.
3. Transmission not engaging.
4. Broken main shaft.
5. Broken countershaft.
6. Broken chain.
7. Broken belt.
8. Broken U-Joint in the drive shaft.
9. Broken CVT unit.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.motorcycleforum.com/97-yamaha/120383-vstar-2004-650-runs-but-wont-go-forward.html
https://www.motorcycleforums.net/forum/yamaha/56841-issues-clutch-2000-yamaha-v-star-650-motorcycle.html
Yamaha XVS650 Service Manual
https://www.partsfish.com/page/oem-parts-for-yamaha
Yamaha star XVS650P Owner Manual

2007 Yamaha V... | Answered on Jul 06, 2019


Hi, William and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the choke.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Quick disconnect check ball stuck.
14. Compression below 75 PSI.
15. A stuck-bent-burnt valve.
16. Improper valve clearance (too tight)
17. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
18. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
19. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
20. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections are loose or connected to the wrong cylinders.
21. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
22. Faulty neutral, clutch, kickstand safety switch.
23. Faulty fuel pump or fuse or relay.
24. Faulty or corroded run/stop switch.
25. Tilt sensor needs a reset.
26. Security system not disarming alarm needs a reset.
27. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://cruiser.mototribe.com/discuss/vstar-problem
What To Do If Your Motorcycle Doesn Start
https://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
https://www.partsfish.com/page/oem-parts-for-yamaha
Yamaha star 1100 Owner Manual

2007 Yamaha V... | Answered on Jun 27, 2019


Hi, Anonymous for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Setting up and Adjusting your TPS
How to clean your TPS sensor Pt 1
Yamaha XVS650 Service Manual
Yamaha xvs650 Supplementary Service Manual
OEM parts for Yamaha
Yamaha star XVS650P Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2007 Yamaha V... | Answered on May 16, 2017


Hi, Quentin your instrument gauges and lights can alert you to most electrical and engine issues they can not warn you about failed engine gaskets or seals so your engine has to resort to old fashion alert methods of colored "SMOKE SIGNALS" here is a breakdown of their meaning:
1. COLORLESS OR SLIGHTLY BLUE SMOKE on start-up means your air/fuel mixture is at the right composition and everything is well burnt in your combustion chamber.
2. BLUE SMOKE on start-up is usually caused by failed valve seals dripping oil into the combustion chamber when the engine is not running.
3. YELLOW OR BROWNISH SMOKE at start-up means your air/fuel mixture is too lean. Too lean means that there is low fuel but high air mixture in your combustion chamber.
4. WHITE SMOKE on start-up may be caused by a blown head gasket allowing coolant to enter the combustion chamber and may start dripping out of the exhaust pipes or mufflers. Smoke while riding is usually caused by worn out or damaged valves, seals, guides, pistons, rings, or cylinder walls.
5. BLACK SMOKE on start-up is usually caused by too much fuel in the combustion chamber this can be due to air/fuel mixture adjustment too rich, accelerator pump improperly adjusted, faulty choke/enrichner or not in the off position, air filter dirty and clogged, faulty carburetor float needle and seat, pilot jet too large, fuel injectors leaking, smoke while riding is usually caused by the main jet being too large or a damaged carburetor.
It should be noted that aggressive or abnormal throttle operation will cause these conditions to manifest themselves exponentially.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Bike running rough puffing black smoke after carb rebuild
Why Black Smoke soot
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
YAMAHA XVS1100 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2007 Yamaha V... | Answered on Apr 23, 2017


Hi, Ricktherabbi for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.starbikeforums.com/forums/49-v-star/19241-speedometer-light-bulb.html
Yamaha Vstar 650 Speedo light Bulb Led Change
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2003/LIT-11626-16-05_22.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2007 Yamaha V... | Answered on Jun 13, 2016


Hi, Jrmoyle for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2003/LIT-11626-16-05_22.pdf
Yamaha
Tips Tricks

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2007 Yamaha V... | Answered on Jun 13, 2016


Hi, Mcisaac87 for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.roadstarmagazine.com/images/pdfs/yam_passing_lamp_mounting.pdf
Motorcycle Lighting and Electrical Guide
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2003/LIT-11626-16-05_22.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2007 Yamaha V... | Answered on Jun 13, 2016


Hi, Mjglbritt I would splice them into the low beam power wire for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Motorcycle Lighting and Electrical Guide
http://www.roadstarmagazine.com/images/pdfs/yam_passing_lamp_mounting.pdf
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2003/LIT-11626-16-05_22.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2007 Yamaha V... | Answered on Jun 13, 2016


Hi, Wainscottbre for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Star rear shock Preload adjustment 650CCND COM
How To Adjust Your Rear Shock On 650 Star
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2003/LIT-11626-16-05_22.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2007 Yamaha V... | Answered on Jun 13, 2016


Hi, Ctex666667 for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Carb sync 650CCnD com
totalmotorcycle com
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2003/LIT-11626-16-05_22.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2007 Yamaha V... | Answered on Jun 13, 2016


Hi, Neonussey and the usual suspects are:
1. Fuel tank empty.
2. Fuel supply valve/petcock turned off.
3. Fouled spark plugs.
4. Engine flooded as a result of overuse of the enricher.
5. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
6. Fuel valve/petcock or filter clogged.
7. Severely discharged or damaged battery, you need 12.5 volts or better and be able to pass a load test if necessary.
8. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
9. Loose or corroded wire connection at the coil, battery or plug between ignition sensor and module.
10.. Spark plug cables in bad condition and shorting, cable connections loose, or connected to the wrong cylinders.
11. Ignition timing incorrect due to a faulty ignition coil, ignition module or sensors (MAP, CMP, CKP, O2, TPS, ETP, IAC,or BAS).
12. Faulty neutral, clutch lever, or kickstand safety switch.
13. Faulty fuel pump or fuse or relay.
14. Tilt sensor needs a reset.
15. Security system not disarming alarm needs a reset.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Motorcycle Message Board Motorcycle USA
no start or no spark
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2003/LIT-11626-16-05_22.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2007 Yamaha V... | Answered on Jun 10, 2016


Hi, Calbai the best way to charge a battery is slowly. I like to use this analogy, would you rather be awakened from a deep sleep with gentle nudging or a violent kick in the rear.
1. Remove battery and check for corroded or damaged terminals clean any dirt, corrosion or electrolyte that is on top of the battery as this will cause premature battery drain, inspect for cracks and swollen/expanded sides which are a sign of overheating and replacement should be seriously considered.
2. Acid plate type batteries should be checked with a hydrometer with recorded readings for each cell to be compared with after charging readings and for sulfation, the cell will appear milky, and incorrect acid level. Fill low levels with distilled water to upper level and remove acid from over filled cells with hydrometer until the level is at the upper mark and dispose of acid in the sink mixed with a quart/litre of water.
3. Connect a voltmeter set on the DC scale to the battery and record the reading for comparison after charging.
4. Attach a drain hose that is not pinched, kinked, or plugged to the nipple on acid plate type batteries and let the other end hang into a plastic or styrofoam cup.
5. Connect a 1-2 amp trickle charger that has automatic charge rate reduction if possible and let charge for 24 hours.
6. After charging recheck each cell with a hydrometer a 100% fully charged cell will have a specific gravity reading of 1.270-1.280 and 1.180-1.190 has only a 25% charge battery should be load tested and considered for replacement if necessary. Reconnect your voltmeter and
any readings in the 10-volt range means you have a dead cell and the battery needs to be replaced. Readings between any 2 cells of 50 points or more indicate the battery has failed and needs to be replaced.
7. No maintenance AGM or GEL batteries need to have a voltmeter reading of 12.8-13 volts for a full 100% charge and 12.2 volts is only a 25% charge and should be load tested and replaced if necessary.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
How to Change the Battery on Yamaha VStar 650 eHow
http://rinasvstar.blogspot.com/2011/01/battery-tender-jr.html
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2003/LIT-11626-16-05_22.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2007 Yamaha V... | Answered on Jun 10, 2016


Hi, Lamanite1677 for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Has any one here pulled the rear wheel off their star
2008 Vstar Rear Tire Change
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2003/LIT-11626-16-05_22.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2007 Yamaha V... | Answered on Jun 10, 2016


Hi, Robert for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.starbikeforums.com/forums/49-v-star/19241-speedometer-light-bulb.html
Changing instrument light bulb on vstar 650
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2003/LIT-11626-16-05_22.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2007 Yamaha V... | Answered on Jun 09, 2016


Hi, Curt for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.starbikeforums.com/forums/49-v-star/48898-can-you-adjust-brake-pedal-position.html
Yamaha XVS650 Rear Brake Lever Height Adjustment
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2003/LIT-11626-16-05_22.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2007 Yamaha V... | Answered on Jun 08, 2016


Hi, Deborahch334 for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
VSTAR Custom
2008 Vstar Rear Tire Change
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2003/LIT-11626-16-05_22.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2007 Yamaha V... | Answered on Jun 08, 2016


Hi, Bobdunneis for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
2001 vstar clicking noise
Need to replace the rear wheel for 01 650 vstar
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2003/LIT-11626-16-05_22.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2007 Yamaha V... | Answered on Jun 08, 2016


Hi, Wesleypeaste and the usual suspects are:
1. Damaged or restricted fuel tank venting system.
2. Loose float bowl screws.
3. Damaged float bowl o-ring.
4. improper fuel level in the float bowl.
5. Worn or dirty inlet valve or seat.
6. Damaged or leaking float assembly.
7. Particle contamination in inlet fitting cavity.
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have nice a day.
https://yamahaclub.com/forums/topic/21039-v-star-650-carb-vent-tube-leak
Star 650 Post GAK Troubleshooting Fuel Leak from Vent Hose
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2003/LIT-11626-16-05_22.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2007 Yamaha V... | Answered on Jun 08, 2016


Hi, Anonymous for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Oil Filters Star 1100 Wiki Knowledge Base
Yamaha Star 650 Oil Change
http://www.sloneservices.com/SilverBack/Other-Stuff/V-StarShopManual99-07.pdf
OEM parts for Yamaha
http://www.starmotorcycles.com/assets/service/manuals/2003/LIT-11626-16-05_22.pdf

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


2007 Yamaha V... | Answered on Jun 08, 2016

Not finding what you are looking for?
2007 Yamaha V Star Classic Logo

Popular Tags

94 questions posted

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

vince

Level 3 Expert

1234 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1176 Answers

Israel Pineiro Jr

Level 2 Expert

165 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

V Star Classic Yamaha

  • V Star Classic Yamaha

Most Popular Question

2007 yamaha 650 vstar leaking oil near

  • Motorcycles
Loading...