Hello---the F1 light is on because the engine computer has detected a malfunction from one of the sensors. This is a a fuel injection malfunction light. The red light means it is more serious and should be checked. You will need to have the fault codes pulled to determine what the problem is and what repair is needed to correct them. A speedo code will also be available for a malfunction. I hope this helps.
Hi, Anonymous and the usual suspects are:
1. Spark plugs in bad condition or partially fouled.
2. Spark plug cables in bad condition and leaking check for spark leakage in the dark.
3. Spark plug gap too close or too wide.
4. Faulty ignition coil, module, and or sensor.
5. Battery nearly discharged.
6. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
7. Intermittent short circuit due to damaged wire insulation.
8. Dirty air filter
9. Intake air leak.
10. Water, dirt, or rust in the fuel system, fuel pump and/or filter.
11. Old dead or bad fuel.
12. Faulty fuel pressure regulator
13. Pinholes in the in tank plastic convoluted tubing from the pressure regulator to the quick disconnect check valve.
14. Fuel tank vent system plugged.
15. Throttle body controls misadjusted.
16. Damaged throttle body or intake seals.
17. Clogged or faulty fuel injectors.
18. Loose, dirty, or corroded ignition module connector at crankcase.
19. Faulty TPS, MAP, CKP, O2, and/or CMP sensors.
20. Incorrect valve timing.
21. Weak or broken valve springs.
22. Damaged intake or exhaust valve.
23. The control module may be in limp mode.
24. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day. http://www.fireblades.org/forums/honda-fireblade/100266-2006-cbr-1000rr-stumbling-low-rpms.html Bikes cutting out at High RPM 2004 2005 CBR1000RR Fireblade Repair Manual Download Manuals Technical $10 http://www.partsfish.com/page/oem-parts-for-honda Honda CBR1000RR Fireblade Owner Manual
Hi, Anonymous and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the enrichner.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead acid batteries.
14. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
15. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
16. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections loose, or connected to the wrong cylinders.
17. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
18. Faulty neutral, clutch lever, or kickstand safety switch.
19. Faulty fuel pump or fuse or relay.
20. A stuck bent or burnt valve.
21. Tilt sensor needs a reset.
22. Security system not disarming alarm needs a reset.
23. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day. HONDA CBR WONT START TRY THESE TIPS What to do When Your Motorcycle Won Start 2004 2005 CBR1000RR Fireblade Repair Manual Download Manuals Technical http://www.partsfish.com/page/oem-parts-for-honda Honda CBR1000RR Fireblade Owner Manual
remove the left faring undo the water pump mounting bolts not all the bolts around the pump just the two that hold it to the engine case pull the pump out about one inch the undo the sprocket cover and remove put the engine in gear and get somone to hold the rear brake on loosen the sprocket bolt undo the rear wheel axle nut and loosen the chain adjusters to put some slack in the chain then remove the front sprocket and fit the new one on put some lock tite on the sprocket bolt and do up tite with the bike in gear and someone holding the brake on put the water pump on and make sure it is lined up properley when you push it back in it should sit flush to the engine with an easy push.adust your chain and titen all the bolts and nuts and refit your faring.hope the was helpfull please leave feedback.
Honda doesn't or claims it doesn't keep record of their transponder passwords, which is prolly true. Dealership will tell you Barrel, and ecu need be changed with new set of keys and tank/passenger seat locks which will run you $1400+. In principal, you can purchase a new ecu with matched blank keys and have them cut to your current key code, which should run you $800ish but i don't know if they will do it.. other cheaper options include: - $250-ish: send ecu to specialized shops that hack it (physically) and reprogram it and then send it back with two matched blank keys (plus $30-ish if you want them cut, but you need to send them the barrel also) - $400-ish: buy used and hacked ecu with matched blank keys..then cut them yourself to your key code. - $100-ish: buy used U.S. spec ECU eliminating HISS altogether, then you can cut keys that will work without programming the transponders, but you will need to alter your wiring harness or buy U.S. loom.( If you have a japan bike you have another wiring problem with the exhaust servo)
P.S. people telling you just to cut keys don't have /have dealt with HISS before. Good Luck