20 Most Recent 1988 Honda XR 600 R Questions & Answers

That means the mixture is too rich in gas.Maybe you should readjust your carburetors

You do not ask an answerable question so if you could post this again in an answerable format I am sure someone will be able to advise you. OR you could buy a service manual and probably find all information you need in it.

You have a wet clutch, and it has many disc's. 1/2 are metal (Aluminum or steel) and the other half are fiber. (Like a brake shoe material) The fiber ones wear out, and it will slip. Most kits have all of the disc's, and that is what you should replace, and then re-adjust your clutch lever.
Remember to soak the fiber disc's in oil before installing new.

DG will be best good power and not so loud and their not very hard to find for older bikes

Salve,
Meglio che vai in una officina autorizata.
Alex

XL 185S HONDA 79 MODEL EXCITER COILS OHMS SPECS ?

Hi , Sorry to hear this about your bike but follow these instruction . Firstly remove the spark plug . put your bike with the back wheel off the grown and in any gear try to turn the back wheel . due to no compression you should technically turn the rear wheel in gear . If this does not work and it will not kick start without the spark plug out and still remain seized i am afraid that you will need to look at getting a new top end rebuilt . Give it a try and let me know how you go .

Place your bike on a paddock stand, rear wheel in the air. Put it in top gear, (if it is difficult to change gear then it may be gearbox and not engine), remove the spark plugs (check for debris on the plugs) and turn the rear wheel slowly. The engine should move with ease, as there is no compression due to the plugs being out.
If it doesn't move, either the engines main bearings or piston/s have seized. It is time to strip the engine down and find out which one!
Check spares prices first as it may be cheaper to buy a recon engine from a warranted dealer, (not a rippoff merchant).
Hope that helped.

the vin no. is located on the headstay just below the handle bars,turn the bars full left then look in front of the fuel tank on the hedstay .

Stalling, won't idle, and glowing header pipes are all symptoms of two possible problems: insufficient valve tappet clearance (adjust the valves), and/or plugged up carburetor from sitting (disassemble the carb and clean it).
Adjust the valves, first - and see if that doesn't solve the problem.

if air is entering the carb anywhere but the intake boot then you will have problems. if the crack is in the float bowl then you are llucky..if not..no big deal you can get a carb cheap from a slavage yard or buy it new ...if there is a crack in the air boot then it will need to be replaced...no mcguyver repairs on that

you have to get the correct cable to replace the one broke,as the inner to outer cable lengths differ on the puul to return,as far as which way round to fit them,the smaller nipples go to the thottle twist grip.

sell it to me?

Check the wiring from the fuse box to the light itself it can be that the wire is loose

The charging system is over charging or you are putting the wrong replacement bulb in. My first thought is that the rectifier has burned out or somehow other malfunction. You will also need to check the battery as a malfunction in the rectifier will over charge the battery and actually boil the liquid (acid) out of it.

it should, this is one of those try it and see situations, youve allready done the hard work now its time to play... HAVE FUN If you need further help, I’m available over the phone at https://www.6ya.com/expert/michael_00678fd4800d19c5

Sounds like a bad rectifier/regulator. Should be 12 volts

Carburetor jet is not adjustable. It has a precise hole size. For richer mixture, replace jet with larger hole.

Hi,

Carburettors are notoriously difficult things to balance without the correct tools. I could not advise that you attempt to try this yourself as there are too many possible variations on the fuel mix and manifold vacuum pressure in the carbs.

The only way to balance carbs properly is to use a mercury manometer. The manometer measures intake manifold vacuume pressure and this tool is specifically designed to set the carbs properly. This will have a major effect on the overall performance of your bike.

Take your xr600 to a proper tuning shop and for a small fee they will set the carbs up properly for you. You will notice a major improvement in the bike and you will definitely not regret it!

Please remember to rate my answer through our rating system. Many thanks for using FixYa.

The serial number on a Honda PC50 moped typically contains important information about the vehicle, such as its manufacturing date and model information. Here's how you can read the serial number: 1. **Locate the Serial Number**: The serial number on a Honda PC50 moped is usually stamped on the frame of the vehicle. It may be located in different places depending on the year of manufacture, but common locations include the head tube or down tube near the handlebars. 2. **Understand the Format**: The serial number may consist of a combination of letters and numbers. It typically follows a specific format that provides information about the moped. 3. **Decode the Information**: While the format may vary slightly depending on the year of manufacture, Honda serial numbers often contain the following information: - Year of Manufacture: The first few characters or digits may indicate the year of manufacture. For example, "73" could indicate that the moped was manufactured in 1973. - Model Information: Following the year, there may be additional characters or digits that represent the model or variation of the moped. 4. **Consult a Reference Guide**: If you're having trouble deciphering the serial number, you can consult a reference guide specific to Honda PC50 mopeds. Online forums, enthusiast websites, or official Honda documentation may provide resources or guides to help you interpret the serial number. 5. **Contact Honda**: If you're still unsure about the information contained in the serial number, you can contact Honda directly or reach out to a Honda dealership for assistance. They may be able to provide you with additional information or help you decode the serial number. By following these steps, you should be able to read and understand the serial number on your Honda PC50 moped, allowing you to gather important information about its manufacturing date and model.