20 Most Recent 2003 Harley Davidson FXSTDI Softail Deuce Questions & Answers

Question edited for clarity and correct the year to 2002. Question moved to model category. A few for sale in the link https://www.google.com/search?q=2002+harley+davidson+fxstdi+softail+deuce+speedometer ..

To the best of my knowledge, your Duece takes three quarts of oil with a filter change. The transmission holds 20-24 ounces of oil. And, your primary takes 38-44 ounces of oil.

Your oil tank has a dipstick in it. Fill the oil tank until the level is just above the lower line with the bike on the stand. The lower line is "FULL COLD" and the upper line is "FULL HOT". Do not overfill.

The transmission is the same way, On the right side clutch release cover, there's a plug that takes a 3/8" Allen or Hex key to remove. It too has a dipstick marked the same way the oil tank dipstick is marked. Check the oil in the transmission with the bike standing straight up.

In the primary, you fill the oil level to where it just touches the lowest part of the clutch spring. The outer clutch housing is bright aluminum. Inside this is a round dark colored piece of metal. This is the clutch spring. Fill or check the oil with the bike standing straight up. Do not overfill as it will make your clutch drag and you will not be able to find neutral with the engine running.

Good Luck
Steve

Hi, Anonymous before diagnosing your blown fuse issue, check the bottom of your seat, if its metal and comes in close proximity to the positive battery post you need to take the necessary steps to ensure there is no contact (electrical tape, thick rubber insulation, hammer a dent in the seat bottom, etc.) You are going to need a wiring diagram from your service manual, a test light, an ohmmeter and plenty of extra fuses. Before continuing, connect the test light clamp to the negative post of the battery and touch the point of the test light to the positive post to validate that your test light is functioning properly.If you turn on your ignition switch and immediately blow a fuse you have a hard/dead short and is usually easy to find. With a test light connected to the hot side of the blown fuse holder start stabbing the wire/s that leads away from the fuse holder and towards the ignition switch, your test light will illuminate validating the short. When the test light fails to illuminate you have passed the short and need to back up until the test light illuminates, then look in the immediate area for the short. If you driving down the road for 30 minutes or 15 miles and blow a fuse you have soft/flying short and may take some time and patience to find.If the main fuse/circuit breaker constantly blows/trips while riding you probably have a faulty battery terminal connection. Check battery terminals for damage or corrosion, check battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary. Any other fuses that constantly keep blowing while riding are usually caused by a loose or corroded ground wire in the circuit, which means you have to check, inspect, test each and everyone with an ohmmeter set on a low ohm scale of 100 ohms or less. Simply touch one lead to the ground source and the other lead to the battery negative terminal, a reading of zero indicates a clean solid ground. Any reading or infinity indicates poor ground and needs to be repaired. Poor or weak grounds require excessive additional amperage to complete the circuit which in turn blows the small amperage fuse. For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.https://www.hdforums.com/forum/touring-models/107238-keeps-blowing-ignition-fuse.htmlhttp://www.mediafire.com/file/65o6mbkdq5ty8ke/99_to_05_Harley_Softail_Service_Manual.pdf/filehttps://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmchttp://mybikemanuals.com/harley-davidson/harley-davidson-softail-owners-manuals/https://www.6ya.com/ to speak to me personally

With the newer HD Security Systems using proximity FOBs where the key FOB needs to be close to the bike to start, this is now more important then ever. If the battery in your FOB dies and you have not set your Harley Alram Override PIN Code, you will not be starting your bike. It is just as important for those with oler Harley Davidsons with the push button alarm FOB. It you set your alarm and the battery dies before you return to your bike, again you will not be starting the bike. If you haven't set the PIN over ride for your HD security alarm system...do it now! Here's how you do it... (To view how to deactivate the security system with the manual PIN code, see below.) Setting or Changing Your Security System Alarm Override PIN Button less fobs (Smart FOB) 1. Select 5 digit code ( each digit being a 1 thru 9) and record it on the wallet card in the owners manual. 2. With an assigned FOB present, turn IGN key ON - OFF - ON - OFF - ON 3. Press Left turn signal switch 3 times. 4. Press Right turn signal switch one time and release. *Turn signals will flash 3 times. Current PIN will appear in the odometer. The first digit will be flashing. 5. Enter first digit (a) of the new PIN by pressing left turn signal (a) times. 6. Press right turn signal 1 time and release. *The new digit (a) will replace the current in the odometer window. 7. Enter second digit (b) of the new PIN by pressing left turn signal switch (b) times. 8. Press right turn signal 1 time and release. *The new digit will replace the current in odometer window. 9. Enter the third digit (c) of the new PIN by pressing left turn signal (c) times. 10. Press the right turn switch 1 time and release. *The new digit (c) will replace the current in the odometer window. 11. Enter forth digit (d) of the new PIN by pressing left turn signal switch (d) times. 12. Press the right turn switch 1 time and release. 13. Enter the fifth digit (e) of the new PIN by pressing left turn signal (e) times. *The new digit (e) will replace the current in the odometer window. 14. Press the right turn switch 1 time and release. 15. Before the module rearms, turn ignition key to OFF. * The odometer will return to mileage display. **Turning the ignition to OFF stores the new pin in the module. Push Button fobs 1. Select 5 digit code ( each digit being a 1 thru 9) and record it on the wallet card in the owners manual. 2. With an assigned FOB present, turn IGN key ON - OFF - ON - OFF - ON 3. Press Left turn signal switch 3 times. 4. Press button on fob twice Current PIN will appear in the odometer. The first digit will be flashing. 5. Enter first digit of the new PIN by pressing left turn signal until the desired number appears. Press button on fob twice to enter number. 6. Enter second digit of the new PIN by pressing left turn signal until the desired number appears. Press button on fob twice to enter number. 7. Enter third digit of the new PIN by pressing left turn signal until the desired number appears. Press button on fob twice to enter number. 8. Enter forth digit of the new PIN by pressing left turn signal until the desired number appears. Press button on fob twice to enter number. 9. Enter fifth digit of the new PIN by pressing left turn signal until the desired number appears. Press button on fob twice to enter number. Turning the ignition to OFF stores the new security PIN. Using the Security Alarm PIN Override to Start Your Harley Davidson 1. Turn the IGN key to IGNITION and immediately hold both turn signal switches until 5 dashes appear in the odometer window. 2. Enter the first digit of your PIN (a) by pressing the left turn signal switch (a) times. 3. Press the right turn signal switch 1 time to move to the next digit. 4. Enter the second digit of your PIN (b) by pressing the left turn signal switch (b) times. 5. Press the right turn signal switch 1 time to move to the next digit. 6. Enter the third digit of your PIN (c) by pressing the left turn signal switch (c) times. 7. Press the right turn signal switch 1 time to move to the next digit. 8. Enter the forth digit of your PIN (d) by pressing the left turn signal switch (d) times. 9. Press the right turn signal switch 1 time to move to the next digit. 10. Enter the fifth digit of your PIN (e) by pressing the left turn signal switch (e) times. 11. Press the right turn signal switch 1 time to move to the next digit. 12. Press the right turn signal switch one time and the security system alarm is turned off.

Spark plug back tip do I replace my jets

Harley Davidson Wiring Diagrams and Schematics ,,,,

Harley Davidson Wiring Diagrams and Schematics