20 Most Recent 2003 Ducati Multistrada 1000 DS - Page 8 Questions & Answers

haha ps don't tell ducati ... you will have to go to a main dealers for this and still I doubt they have the tools to sort this one ....memory is saved on your cdi unit (basically a mini computer ....removing the battery should NOT have affected it

You are at a service interval. The dealership is the only place to get these reset. It probably (depending on the miles) needs a valve adjustment check. If it's running fine then you can ignore it until you take it to a dealership.

Pull a spark plug wire and hold it close to the engine. Try to start the bike to see if there is spark from the wire to the engine block. If yes, then check your plugs and fuel supply. If no, hve the coil checked.l

Nope. None. Add a toggle switch to power aux components, but dont leave it on or it will drain the batters, hence why there is no aux position on the key.

You likely either have a blown master fuse or you have bad electrical terminals or a bad ignition switch.

Not a specific answer, but my advice is; the best money you'll ever spend is to get a service manual from say amazon for example. You can spend quality time reading through it while enjoying you beer!

Is the clutch working correctly are the plates compressed. Without operating the clutch lever the clutch should be fully lock the center hub to the outside cage. Does the clutch front plate move when you squeeze the lever? If not I would suggest the springs are: - a) too long, b) not correct for your model or c) have too much tension in them and so holding the clutch open. I know they cost more but I would get OEM springs. Hope this helps

Go to Seargent seats web site here World Sport Performance Seat and view installation instructions on the bottom left of the page. You have to remove the fuel tank to get the seat off so it is best to use these instructions.

Most Instrument bulbs push up from the underside of the Display. Look for a round rubber plug with two wires coming from it. Pull it out by hand and replace the bulb then push back it.

this could be a number of things from the type of pipes you have to the electronics the best way forward is take it to your dealer and he will be able to help with his dyno , cheers pete

Happens all the time. Let me guess, front brake handle? WD-40. Then remove the microswitch from the handle. Then wash it down with solvent and spray some more WD-40 on it. I end up pulling mine off to clean it about twice a season.

sounds like the starter solenoid is stuck.

Probably Not, as it is a fuel injected model. The ECU takes information from road and engine speed, some of the sensors are in the instrument panel. The only way to know for certain is to start it.

its proberbley because you put to much oil in on your last oil change empty it out and fill it to the right amount

Two possibilities;1. bulb burnt out2. bulb looseFirst try banging on the tail light with medium force to engage the connection. It worked for me.Failing that you may have to replace the bulb assuming all wirings ok. Good luck

you need to start at the plug and work back check lead then coil can be as simple as the lead has come loose from the coil or the or the lead has deteriated on my trumpy it was the cdi unit

the mufflers act to create back pressure and the air filter acts to restrict air intake. the cheapest way forward would be to re-jet the carbs, might be worth getting matching k&n type air filters to match

You may want to check out your regulator. It "cleans" the power coming from the stator. You may be blowing those fuses because of that. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/randall_17db19439e8e78e3

Some common causes and potential solutions: Air/Vacuum Leak: If your Harley develops a vacuum leak in its air intake system, the air-fuel mixture becomes too rich. This can cause frequent stall outs, especially after the bike warms up. Vacuum leaks often occur due to dried-out or cracked air intake boots, faulty gaskets, or worn-out carburetor seals. When air escapes from the intake system, the fuel fills the empty space in the combustion chamber, altering the air/fuel ratio and negatively impacting combustion. Severe vacuum leaks can lead to excess fuel flowing into the exhaust system, causing backfiring and stalling while riding. Clogged Fuel Tank Filter/Fuel Injectors: A blocked fuel tank filter (due to coagulated fuel, moisture, dirt, or corrosion) impairs fuel flow, resulting in a lean air/fuel ratio. On fuel-injected Harleys, clogged fuel injectors produce similar symptoms. Regular maintenance, including cleaning and inspecting fuel filters, helps prevent these issues. Faulty Cam Chain Tensioner: A malfunctioning cam chain tensioner can affect engine timing and cause stalling. Regular checks and replacements are essential to avoid this problem. Faulty Cam Position Sensor: The cam position sensor plays a crucial role in ignition timing. If it malfunctions, it can lead to stalling and backfiring. Clogged Air Cleaner: A dirty air cleaner restricts airflow, affecting combustion efficiency. Regularly clean or replace the air filter to prevent this issue. Ignition System Failure: Faulty ignition components (such as spark plugs, ignition coils, or wires) can cause misfires, backfires, and stalling. Inspect and maintain these parts regularly. Compromised Battery Terminal Connection: Poor battery connections can disrupt electrical flow, affecting the ignition system. Ensure clean and secure battery terminals. Remember that diagnosing and addressing these issues may require professional assistance. Regular maintenance and timely repairs can keep your Fat Boy running smoothly on the road.