2007 Harley Davidson FLSTC Heritage Softail Classic - Answered Questions & Fixed issues

Question edited to add maker. Question moved from 'Garden' to model category. https://www.google.com/search?q=2007+Harley+Davidson+Heritage+Softail.+I+have+P1004

Help! P1004 error - Harley Davidson Forums

Harley Davidson Forums https://www.hdforums.com > ... > Touring Models Apr 7, 2017 - My bike is running rough today, I checked it and I get the error code P1004 - System Relay Contacts Closed EFI Does anyone know what causes this failure? Periodic engine light and red Key light on FB Sep 10, 2008 2010 Heritage Softail Classic died & no start Sep 7, 2020 anyone have trouble with system relay? Jul 30, 2009 More results from www.hdforums.com Missing: Heritage ‎' Must include: Heritage

Harley Diagnostic Codes

ThunderMax https://www.thunder-max.com > techdocs > harl... PDF Harley Diagnostic Codes ... To get the DTC within an area of diagnostics, push and hold the odometer reset button in ... P1004 System Relay Contacts Closed. 4 pages

My husband has a 2007 Harley Davidson Night Train and it has

JustAnswer https://www.justanswer.com > motorcycle > 77k98-hu... Oct 6, 2012 - B1004 is an invalid code. P1004, however, is not. P1004 is a problem with the system relay. the system relay provides power to the fuel pump, ... 1 answer · Top answer: Welcome. Thank you for choosing Just Answer. I need to start with more s ..

fault light - Harley Davidson Forums

https://www.hdforums.com > ... > Dyna Glide Models Afterward, while riding, my engine light came on. I extracted the code from the speedo, and got "P0154..... Rear 02 sensor open/not responding..... PN32919-07". You visited this page on 02/01/23.

My 2007 harley-davidson given me these codes PN 67478 ...

https://www.justanswer.com > ... > Motorcycle Questions Aug 19, 2009 - My 2007 harley-davidson given me these codes PN 67478-04A ,PN 32919-07 ,and PN 68921-07 - Answered by a verified Motorcycle Mechanic. 1 answer · Top answer: Those are not codes ..they are displayed when retrieving codes with the speedo ...they are ...

• Was idling very high on start up and dying anytime I stopped.

  https://www.justanswer.com > ... > Motorcycle Questions Mar 30, 2012 - Need some help - PN 32919-07A. 08 FXD, fully stock. Was idling very high on start up and dying anytime I stopped. Replaced the plugs and ran ...

Buy a HD manual $50

Try google it on line or you tube or Google Harvey Davidson email and see if the answer your question

The cable and housing must be replaced as a unit

Check fuses under seat in fuse box.

Adjust brake light switch at pedal or right lever.

I heard that if you remove the dipstick the oil will flow better. Hope this helps.

How to replace starter clutch 2007 harley heritage YouTube

Something here should help. How to replace clutch pak 2007 harley davidson heritage YouTube

Brake disc screws, front, are 16-24 ft-lbs

VOLTAGE REGULATOR Removal/Installation Disconnect the negative battery cable Remove the rear fender inner panel raising the back wheel off the ground, remove the 2 bolts securing it at the bottom, push it up to release it as it clips over a locating tab Disconnect the voltage regulator lead from the silver post on the main circuit breaker. Prior to removing the voltage regulator wires, note the routing of the wires through the frame. Note the location of cable straps and tie wraps. The wires must be rerouted in the same path. After disconnecting any straps, leave them in place on the frame as a reference for installation of the wiring. Disconnect the voltage regulator electrical connector from the alternator stator. On 2001-on models, Remove the two bolts securing the voltage regulator to the mounting bracket. Remove the screw and disconnect the ground strap from the mounting bracket. Unhook the wire retainer from the mounting bracket. Remove the voltage regulator and related wiring from the frame. Install by reversing these removal steps. Note the following:

You have a short in that circuit, check for loose or bared wires in the headlight or blinkers or disconnect any plug. Leading to those parts one at a time until the fuse stops blowing then trace those wires to the problem

Getta clymer manual for shop details or library sec629

As far as the rear suspension, a softtail won't ride a smooth as one with a swingarm, as the softtail has less travel. On the front end, Harley has three different "thicknesses" of fork oil, light, medium, and heavy, which gives different suspension dampening. If the front forks are too stiff, you could try a lighter fork oil.

From your description, the following is usually the cause: Remove twist grip from end of handlebar, and apply a THIN coating of hi-temp grease to the handlebar end where the throttle sleeve rides. Lube the throttle cables. Check cable routing, making sure that there's no tight bends, and it's not hanging up, or pulling. Check for weak/broken throttle return spring (if there i one)

Yes, you will want to remap. Not sure of the cost. What about oil from the K&N depositing and deteriorating the MAP sensor??????

Hi, It is possible that you have a bad ground. Also check the bulb for corosion on contacts. Check fuses located under the seat. Hope that helps.

Check those codes....

It's probably your front brake light switch is broke. You must take the right handlebar switch housing apart to replace that switch.

Good Luck
Steve