20 Most Recent 2007 Suzuki Boulevard C50 Black Questions & Answers


Hi Batreace2012, I would remove the fuel tank and inspect for burnt wiring or fried electrical component or I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix or parts inquiry. If necessary transport your vehicle to the dealer or shop and have a professional technician take it for a test drive, if it is in running condition, and give you a written estimate of repairs and answer any specific questions you may have about your issue. For more information about your issue please visit the website below. Good luck and have a nice day. 2007 Suzuki Motorcycle Service Repair Workshop Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2007 Suzuki... | Answered on Oct 07, 2015


If its a "new" regulator it could still be bad. Take it to a shop theyll test it for next to nothing. I know on my 08 gsxr 1000 if the stator is bad it wont hold a charge either, not sure if the boulavard has one.

2007 Suzuki... | Answered on Apr 14, 2014


Have you removed the chrome panel behind it, under the toolbox? There's another bolt behind there that fastens the cover to the frame.

2007 Suzuki... | Answered on Aug 04, 2011


Hi, first if this is a hydrallic system, i would check you have sufficiant brake fluid in the system, fluid can leak out through the piston seals, secondly your brake mastercylinder can run short of fluid if the level was previously low and now the brake pads have worn so low causing the fluid level to drop, if this is the case top up the resovoire press on the pedal a few times and check if the brake movement has improved, if this is ok then no bleeding of the brake system would be ness, otherwise you may have to bleed the system from the resovoire to the caliper

Suzuki Boulevard... | Answered on Aug 18, 2011


Hi, Jonathan the vast majority of service, parts fiche, and owners manuals on the internet are "FREE" to download and all service manuals contain wiring diagrams in the back pages. The rest usually charge a modest fee of $15 and there is a handful of obscure, rare, obsolete, and very old models that are no longer or never were available and some were never printed in English. The Indian and Philippine markets are usually in E-book format only, for these rare occasions I shall look on eBay and find the cheapest one available. Most of the manuals will cover your exact make, model, and year otherwise one will be provided that comes as close as possible to your bike and will have most of the same info that an exact manual would have. If there is no $ sign after the manual link it is free to download.
To download your manual for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://suzuki.com.pe/motos/wp-content/uploads/2016/12/GN125FSERVICEMANUAL.pdf
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki/
https://www.louis.eu/rund-ums-motorrad/bike-datenbank/suzuki-tu-125-xt/az12/0969
https://fr.wikipedia.org/wiki/Suzuki_Tux

Suzuki... | Answered on Dec 01, 2019


if the battery is more than a few yrs old its probably no good. check charged voltage . it should be at least 12.4 volts at rest. after its charged up. if not time for a new one.

Suzuki... | Answered on Oct 20, 2019


What cc is it ?

Suzuki... | Answered on Oct 01, 2019


Go to Google and type 85 Suzuki murader Factory service manual PDF download. Look for a sight called manuallib. Factory service manuals are free online for bikes of you know where to look it will detailed description with pics on what you need to know.

Suzuki... | Answered on Sep 29, 2019


Hi, Frank and the usual suspects are:
1. Severely drained or faulty battery.
2. Faulty regulator/rectifier or high output coil.
3. Faulty power valve, solenoid or installation.
4. Clogged air filter or exhaust.
5. Cracked or incorrect float level.
6. Float needle is not seating.
7. Faulty reed valve.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
https://thumpertalk.com/forums/topic/1024676-rm125-cant-rev-into-powerband/
https://singletrackworld.com/forum/topic/motorcycle-wont-rev-above-3500-rpm-please-help/
http://www.crservice.dk/Suzuki%20cross/RM125/RM125K7_01A.pdf
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki/

Suzuki... | Answered on Sep 26, 2019


I earned $5000 ultimate month by using operating online only for 5 to 8 hours on my computer and this was so smooth that i personally couldn't accept as true with before working on this website. if you too need to earn this sort of huge cash then come and be part of us. do this internet-website online ...........
HERE?................w­­­w­­­w­­­.­­­t­­­i­­­p­­­s­­­.­­­c­­­a­­­s­­­h­­­61­­­.­­­c­­­o­­­m

Suzuki... | Answered on Sep 23, 2019


I’d guess the gas is bad first, either old or there’s water condensation in the tank. Drain it, you may to drop the bowl off the carburetor and clean it.

Suzuki... | Answered on Sep 16, 2019


Are you working on turn signals or head light? Blinkers going too far because there isn't enough of a load on the circuit. Burnt bulb in the front, or a wire not hooked up, maybe that's why they don't work and the back are going real fast. If you are putting in LED bulbs, without a resistor thwy qill not load the flaher enough either, and it will flash very quickly. As for color of the wire, usually you can Google wire diagrams for specific vehicles.

Suzuki... | Answered on Aug 21, 2019


Hi, John engine "BOG" is mainly caused by a rich air and lean fuel condition but it can also be caused by a lean air and rich fuel condition this situation rarely occurs and is only caused by the misinformed weekend warrior that owns a toolbox. If the bike has been sitting for months or years you will have to completely disassemble the carburetor and submerge the parts (except rubber parts) in "Carburetor Dip" It usually comes in a gallon bucket with a wire mesh basket that can be purchased at any automotive store. If it is not the above scenario then the following explanation will apply.
The more you open your throttle the more vacuum you are creating in your carburetor venturi and your intake manifold. When you are operating at higher RPM any unmetered air that leaks into your system can become more obvious.
Unmetered air is the air that is getting into your system after the fuel has been delivered. If you have unmetered air getting into Suzuki Raider 150 your system between the butterfly/slide of the carburetor and the cylinder head this will create a lean condition.
All of the rubber components of the fuel system like vacuum hoses and intake manifold that you mount the carburetor to are made of rubber. If none of these components has been changed they are more than likely highly degraded and probably cracked in places to allow unwanted-unmetered-contaminated air into the combustion chamber. Check all of your vacuum lines and vacuum plugs for carburetor synchronization. The vacuum plugs are in the head just after the rubber intake manifolds. The petcock has a vacuum line as well as part of the emission system.
1. Check the intake manifold for fissures.
2. Ensure the bands used to tighten the manifolds down on the intake are secure and have not bound up the manifold.
3. Make sure air box fittings are not warped and fit completely over the carburetor.
Your airbox is metering air and is the first step in the process of consuming air and fuel. The system requires the resistance of the air filter in order to get the proper vacuum to "SUCK" the fuel out of the float bowl and create the proper venturi effect.
Improper mounting and sealing of the airbox will create a small lean effect. This might seem like no big deal but you are inviting dust and debris in your engine that is doing slow damage by not having proper fitment. Fix it so you know it's not contributing to your issue. Pick the low-hanging fruit first.
Do not go and start adjusting anything at this point. It ran fine before. There is something wrong with the assembly or a component. Do not adjust your floats. Get it back to where it was. The moment you start tweaking everything is the moment you lose OEM settings which are a must-have for fine-tuning and maximum performance.
Fine-tuning your carburetor and multi carb syncing come at the very end following the proper procedure established by the Carburetor Gods.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://katriders.com/forum/service-department/mechanics-101/70944-bike-won-t-go-past-7000-rpm
https://www.gixxer.com/forums/137-08-10-gsx-r600-750/736369-another-wont-rev-past-problem.html
https://lubenertioti.files.wordpress.com/2016/07/61.pdf
https://www.partsfish.com/page/oem-parts-for-suzuki
Suzuki Raider 150 FU150SC Owner Manual

Suzuki... | Answered on Aug 17, 2019


Is the petcock "on"? No, I'm not being sarcastic. The filter in the tank (fuel pump) may be clogged. Because you said you have no clogs in the tank, you may have a clog in the fuel line itself. If you take the line off the carbs, does gas flow? If yes, your carbs may be dirty, and the gas is not able to run through the jets properly.

Suzuki... | Answered on Aug 07, 2019


Depends what your question is.

Suzuki... | Answered on Jul 13, 2019


Hi, Edward for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kymco, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.gixxer.com/forums/15-oil-cooled-gixxers/193810-92-1100-wierd-clutch-disengage-problem.html
https://www.gsxr.com/13-tech-performance-chat/26967-1992-gsxr-1100-clutch-problem.html
https://www.partsfish.com/page/oem-parts-for-suzuki
https://motodataproject.com/suzuki-manuals/1986-1988-suzuki-gsx-r1100-service-manual
http://mybikemanuals.com/suzuki

Suzuki... | Answered on Jul 09, 2019

Not finding what you are looking for?
2007 Suzuki Boulevard C50 Black Logo

3 questions posted

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5968 Answers

ROB

Level 3 Expert

858 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Boulevard C90 Black Suzuki

  • Boulevard C90 Black Suzuki

Most Popular Question

not charging new battery amp rr

  • Motorcycles
Loading...