kawasaki ZZR 1100 - Answered Questions & Fixed Issues - Page 8

Rotors:
http://store.58cycle.com/SearchResults.asp?Search=1992+ZZR+1100

Here are some more:

http://www.1tail.com/Brakes/Kawasaki_ZZR1100_Rotors/

Windscreens (Not sure if you're in the U.S.A)
http://www.motowebshop.com/en/motorcycle_parts/kawasaki/1992/zzr_1100_c/mra_-touringscreen

https://www.bike-design.com/search.php?page=9&shp_category=93&shp_make=0&shp_model=0&shp_year=0

http://www.proaccessories.com.au/products/mra.htm

Here's one in the USA:
http://www.puigusa.com/tuning-bikes/kawasaki-zzr-1100-1992/replacement-screens/c171en/f213-m868/

the fuse box is under the seat alongside the junction box..

first check the bulb...u can easily do that by putting it in another pig tail that you know works..if ok, check connection on shift sensor on engine, usuall located somewheres near the shift drum & will be on the outside of the engine.the shift sensor is just a short to ground system..disconnect the wire & with a continuity meter shift bike to determine if the fault is with the sender or the wire that feeds power to the indicator light in your dash..

it could be just a bulb in the clock or it could be the switch in the gear box, even a broken wire could stop the light from working,,,

Each manufacture has different ranges for different bikes. So the answer would probably be best found in your owners manual for your specific bike. If not, just call you dealer and speak to the guys in service and they should know what temperature your bike should run at.

go to www.ronayers.com and you can look up many microfiche pictures. Hope this helps you... I use it all the time.

The relay is in/on the circuit board mounted under the seat. Should have one large or two small pulgs going to it. Two small realys on that board. Best way to check the power out of the realy to the fuel pump is to unplug the pump and read the two wires for 12 Vdc.  

Assuming the clutch is operating properly the problem sound like it lies in the gear case, possbily a worn or bent shift fork, sorry but it sounds as if you will need to split the cases.
Tom

www.kawasaki.com

Not really it all depends on what you like. There are many after market ones available. You might use this opportunity to pick up a set that is positioned closer to your riding style. You want to be sure to reuse the counter weights also.
Why did your set break? If not from an accident I would revisit a dealer to determine if they were defective. Hope this helps.

JP

yes you can mate i use semi synthetic in my gsxr1000

sounds more like a neutral sensor switch or the wire. if your particular bike requires the deployment of the clutch to start then the same applies to the clutch sensor,

Just from the oil sitting. I recommend oil flush. Also a valve job is not a bad idea either

hi jason,the first thing that springs to mind is that the bike was not designed to have topboxes mounted to them,as the topbox will upset the aerodynamics of the bike and the weight distribution,even the honda goldwings with all of their hard luggagr have a warning from the factory about not exceeding120kph with hard mounted luggage,for the reason i mentioned above,however if you check the steering head bearing tension and compensate for the extra weight carried by adjusting the compression settings on your front and rear susspension,and lifting yourtyre pressure by a couple of psi front and rear it may help to aleviate some of the problems you have,hope this helps

Oil rype is important on wet clutches. Wrong oil will cause this problem. Motor oil is a no no - good luck

get your caborater clean and for more info contact http://tinyurl.com/msfzw7

If it's definitely oil-smoke (blue-white) it might be worn rings/bores that were the problem or possibly the valve-guides themselves.
What mileage is on the bike?
I assume the oil-level is ok, not too high.
Could also be a head-gasket fault.
If you do a lot of short runs it could also be condensation build-up
coming out as steam, sounds daft but maybe v0v

Check the fuse box for blown up fuses.
Measure the electrical current thoroughly from battery to cockpit and find out where it cuts off.Plug by plug.

Have you tried downloading bearshare? Get most instruction manuals on that.

go to service center