Location of ac high pressure cutout switch on a 97 Plymouth voyager. Could it be a different problem? Had to replaced the PCM and a couple sensors because of a short in the wiring cluster. Now the ac blows out hot. the clutch doesn't spin. have coolant pressure in the high pressure line.

stuck relay wire short

the oil pressure sensor can do that. have you checked the oil.

Hi there:

On 1996 Plymouth Truck Voyager 2WD 3.3L MFI 6cyl the ECM (Engine Control Computer) is located under hood, driver side, front side of strut tower, mounted on inner fenderwell.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

You may have two different problems.
The rich mixture could be several things including a faulty O2 sensor or leaking injector. If a sensor fails it should set a code in the computer.
The stalling could be a dirty throttle body or a problem with the idle speed control valve.

CHRYSLER OBDII DTC

P1101 HCM/PCM Communication Performance

P1103 Turbocharger Waste Gate Actuator Malfunction

P1104 Turbocharger Waste Gate Solenoid Malfunction

P1105 Fuel Pressure Solenoid Malfunction

P1195 Slow Switching O2 Sensor Bank One Sensor One During catalyst monitoring

P1196 Slow Switching O2 Sensor Bank two Sensor one During catalyst monitoring

P1197 Slow Switching O2 Sensor Bank One Sensor two During catalyst monitoring

P1198 Radiator Temperature Sensor Input voltage too high

P1199 Radiator Temperature Sensor Input voltage too low

P1281 Engine is cold too long

P1282 Fuel Pump Relay control circuit

P1283 Idle select signal invalid

P1284 Fuel Injection pump battery voltage sensor out of range

P1285 Fuel Injection pump controller always on

P1286 Accelerator Position Sensor (APPS) supply voltage too high

P1287 Fuel Injection pump Controller Supply voltage low

P1288 Intake manifold short runner tuning valve solenoid circuit

P1289 Manifold tune valve solenoid circuit

P1290 CNG Fuel system pressure too high

P1291 No Temp rise seen from intake heaters

P1292 CNG Pressure sensor voltage too high

P1293 CNG Pressure sensor voltage too low

P1294 Target idle not reached

P1295 No 5 volts to TP sensor

P1296 No 5 volts to MAP sensor

P1297 No change in MAP sensor from start to run

P1298 lean operation at wide open throttle

P1299 Vacuum Leak detected (IAC fully seated)

P1300 Ignition timing adjustment circuit failure

P1388 Auto shutdown relay control circuit

P1389 No ASD relay output voltage at PCM

P1390 Timing belt skipped one tooth or more

P1391 Intermittent loss of CMP or CKP

P1398 Mis-Fire Adaptive Numerator at Limit (PCM is unable to learn the crank sensors signal

for use in preparation for misfire diagnostics

P1399 Wait to start lamp circuit

P1403 No 5 volt feed to EGR

P1475 Auxiliary 5 volt supply is too high

P1476 Too little secondary air

P1477 Too much secondary air

P1478 Battery Temp Sensor Volts out of limit

P1479 Transmission Fan Relay Circuit

P1480 PCV Solenoid Circuit

P1481 EATX (Electronic Automatic Transaxle) RPM pulse generator performance

P1482 Catalyst Temperature Sensor Circuit shorted low

P1483 Catalyst Temperature Sensor Circuit shorted high

P1484 Catalytic Converter overheat detected

P1485 Air injection solenoid circuit

P1486 EVAP Leak Monitor found a pinched hose

P1487 Hi Speed Fan #2 Circuit

P1488 Auxiliary 5 volt supply output is too low

P1489 High speed fan control relay circuit

P1490 Low speed fan control relay circuit

P1491 Radiator fan relay control circuit

P1492 Ambient/ Battery Temp sensor input voltage too high

P1493 Ambient/ Battery Temp sensor input voltage too low

P1494 Leak detection pump pressure switch or mechanical fault

P1495 Leak detection pump solenoid circuit

P1496 5 volt supply, output too low

P1498 High speed radiator fan ground control relay circuit

P1500 General alternator 'FR' Terminal circuit fault

P1594 Charging system voltage too high

P1595 Speed control solenoid circuits

P1596 Speed control switch always high

P1597 Speed control switch always low

P1598 A/C pressure sensor input voltage too high

P1599 A/C pressure sensor input voltage too low

P1680 Clutch released switch circuit

P1681 No I/P Cluster CCD/ J1850 messages received

P1682 Charging system voltage too low

P1683 Speed control servo power control circuit

P1684 The battery has been disconnected within the last 50 starts

P1685 The SKIM (Smart Key Immobilizer Module) has received an invalid key

P1686 No SKIM (Smart Key Immobilizer Module) bus message received

P1687 No Mechanical Instrument cluster bus message

P1688 Internal Fuel injection pump controller failure

P1689 No communication between the ECM and injection pump module

P1690 Fuel injection pump CKP sensor does not agree with the ECM CKP sensor

P1691 Fuel injection pump controller calibration error

P1692 Fault in companion Engine control module

P1693 A companion DTC was set in both the ECM and PCM

P1694 No CCD message from PCM- Aisin transmission

P1695 No CCD message from body control module

P1696 PCM failure EEPROM write denied

P1697 PCM Failure SRI (Service Reminder Indicator) mileage not stored

P1698 No CCD message from TCM

P1719 Skip shift solenoid circuit

P1740 TCC solenoid or overdrive solenoid performance

P1756 Governor pressure not equal to target at 15-20 psi

P1757 Governor pressure is above 3 PSI when 0 PSI is requested

P1762 Governor pressure sensor offset improper voltage

P1763 Governor pressure sensor voltage to high

P1764 Governor pressure sensor voltage to low
P1765 Transmission 12 volt supply relay control circuit

WELL I AM LOOKING AT AUTOMATIC SHUT RELAY BAD OR THE BAD COIL POWER TRANSISTOR.YOU WILL NEED A SCANNER TO TELL YOU IF YOUR CMP SENSOR OR CKP SENSOR IS WORKING.

The problem is not with the switch, it's the blower motor resistor. The resistor is usually located in duct work near the blower motor. It will have 4or 5 wires going to it and is held in place with a couple screws. These things generate heat, so they put them in duct work so the fan blows air across them to keep them cool. Sometimes the plug gets hot and melts, you should be able to buy the resitor and the plug with wires (pig tail) from an auto parts store or a dealer. The resistors are usually about $50 the pig tail is about $30.

hi,

There are four screws in totoal. The first two are located at the top of the cover, just under the lip. The second two are at the very bottom under a small grey cover. You need to pry the small grey cover off and you'll see the bottom screws. After you remove all four screws, it'll pop right off.

i believe it is on front of the engine by ac compressor it screws into the block