Question about 1999 Dodge Caravan

1 Answer

How to locate the crank positioning sensor on a 1999 dodge caravan 3.0 l motor

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 3,640 Answers

The crank position sensor is located on transmission housing near the top at back of engine. this is for a 97 but yours should be the same. if not there, check left side rear of engine. good-day!

Posted on Jul 22, 2011

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 dodge caravan 2.4 , location of crankshaft position sensor?


2005 Dodge Caravan SE 2.4L Engine. Crank Shaft Sensor is located on the front of the engine (side toward the radiator) and right below the starter.
Raise the vehicle on stands or ramps. From under the vechcle, unclip the wire plug. Loosen and remove the 8mm bolt. Pull out old sensor.
This CAN be done WITHOUT removing the starter. Easiest way is to use a deep 8mm x 1/4” drive socket and good lighting. I had to use vise grips to grip and pul out the old sensor. It is okay to twist and pull.
NOTE: I have seen many posts placing this sensor in all kinds of places. For this vehicle, this is where it is located. If you have a different engine or year, it could be located someplace else.

Sep 14, 2011 | 2005 Dodge Caravan

2 Answers

Want to locate where is the crankshaft sensor on 2005 dodge grand carvan 3.3 eng


Hello brscwb,

Below is an image depicting the location of the crank sensor.

I hope this helps.

netvan_130.png

Regards,

natven

Aug 02, 2011 | Dodge Caravan Cars & Trucks

2 Answers

1999 dodge caravan with 2.4 cylinder engine. no spark. check timing, replaced coil pack, replaced computer still no spark any ideas


Crankshaft senor. This sensor supplies info to the ECM, that inturns sends the info to the ignition module that controls the spark. Check the codes.

Feb 07, 2011 | 1999 Dodge Caravan

2 Answers

Where is crank sensor located on a 1991 dodge caravan 3.3 engine


For 1991 Dodge Truck Caravan 4WD 3.3L MFI 6cyl the Crankshaft Position Sensor is located: Under hood, center, rear engine area, where transaxle bellhousing meets engine, mounted in engine block.

Hope this Helps (remember to rate and comment this).

Oct 02, 2010 | 1991 Dodge Caravan

1 Answer

2001 dodge 3500 van cam position sensor location


Crank sensor is in the bell housing of the transmission. Cam sensor is in the distributor.

Jul 25, 2010 | 2001 Dodge Ram 3500 Truck

1 Answer

1998 Caravan: where is the crank sensor located on the 98 carava...


The crank sensor is located on the top side of the transmission about 11:oo clock position

May 18, 2010 | 1998 Dodge Caravan

1 Answer

Where is the crank position sensor on my 2004 van


located on the transmission in the rear of the engine where the engine and trans bolt together small cyinder with a ribbon wire coming from it

Oct 10, 2009 | 2004 Dodge Grand Caravan

1 Answer

How to reset a maintenance light after a oil change on a 1997 Dodge caravan 3.3L


Reset the Dodge PCM - Instructions:
  1. Open the hood of the Dodge
  2. Locate the battery and remove the black-wired negative terminal from the battery.
  3. Turn the ignition key to the "on/crank" position for 30 seconds, then replace the ignition key to the "off" position.
  4. Reconnect the negative battery terminal and close the hood.
  5. Turn the ignition key until the Dodge starts and allow it to idle. Check the dashboard for the malfunction indicator light status.
I hope help you. Good luck (remember rated)

Sep 25, 2009 | 1999 Dodge Caravan

1 Answer

Crank position sensor:Where is it at on a 2002 dodge grand caravan


On the 3.3 3.8 engine it is located where the transmission meets the engine block at the rear near the rear engine mount.

Oct 17, 2008 | 2002 Dodge Caravan

1 Answer

1997 Dodge caravan crank position sensor


it is located on the bellhousing of the transmission it gets its signal from the flywheel.look where the transmission bolts to the engine.

Sep 25, 2008 | 2002 Dodge Caravan

Not finding what you are looking for?
1999 Dodge Caravan Logo

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...