I need a fan belt routing diagram for my 1999 caravan 4cyl

if the belt is still on the car take a picture to know the routing of it. there should be a decal under the hood somewhere that shows the belt routing.

The serpentine belt on the 1997 Dodge Caravan is responsible for keeping the front engine accessories working at all times. To change it, raise the hood, and locate the small belt routing diagram on the top/left side of the plastic fan shroud cover. Use the routing directions from the diagram to install the new belt.Use the bolt head that secures the tensioner pulley to the tensioner arm to rotate the tensioner. Slide the belt off of the tensioner pulley.may be it can help you and good luck------------------------------------------------------------------
zed-bull key programmer

You can look that diagram up in the DAYCO belt routing guide at this link.

Yopu can look that up here

Heated Windshield Wiper Blades

Timing belt routing diagrams for cars and trucks? Click the link below:--- http://technoanswers.blogspot.com/2011/10/timing-belt-routing-diagrams-for-cars.html

Drive belt routing diagrams for cars and trucks? Click this link below:--- http://technoanswers.blogspot.com/2011/10/drive-belt-routing-diagrams-for-cars.html

Instructions

Things You'll Need
3/8-inch drive breaker bar
Metric sockets
Serpentine belt

1 Open the hood and inspect the flat surface on top of the plastic fan shroud for the belt routing diagram. Follow the diagram instructions to route the new belt.

2 Locate the serpentine belt self-adjusting tensioner on the front of the engine block. The tensioner has a pulley on the bottom of the tensioner arm, which the belt travels under. The tensioner can only be rotated from the bolt that secures the pulley to the tensioner arm.

3 Rotate the tensioner in a clockwise motion with a metric socket and the breaker bar to loosen the tension from the belt. Then, pull the belt off the top of the tensioner pulley. Release the tensioner pulley and pull the breaker bar off the pulley bolt.

4 Pull the belt out of the accessory pulleys. Then, slide the belt around each fan blade and out of the engine bay. Rotate each fan blade to the top side of the engine to get the belt around each fan blade.

5 Match both the new belt and the old belt together to make sure that the new belt is the correct size. Then, route the new belt around each fan blade and around the crankshaft pulley. The crankshaft pulley is the big pulley at the very bottom of the engine.

6 Follow the routing directions from the belt routing diagram to install the new belt around the other accessory pulleys. Once the belt has been routed around all of the pulleys, look over the belt and make sure that it is secure inside all of the pulleys.

7 Crank the 1998 Dodge Caravan and let the motor run for about 15 seconds. This will finish seating the ridges of the new belt into the grooves of each accessory pulley.

8 Shut the motor off and close the hood.

The alternator belt on the 1999 Dodge Caravan also controls the air conditioner compressor, the water pump and the power steering pump. The belt is called a serpentine belt, and it is designed to fit around all of the accessory pulleys at the same time. As the belt travels around each accessory pulley, it enables the accessory to operate. Once the belt is damaged, cracked or frayed, you should change it before it breaks. If that happens, each of the accessories will stop working.

Open the hood and prop it up so that it does not fall. Engage the parking brake.

Inspect the top surface of the fan shroud for the serpentine belt routing diagram. Follow the routing instructions on the diagram to install the new belt.

Locate the serpentine belt self-adjusting tensioner on the front of the engine. The tensioner is directly below the alternator. Use the bolt that connects the tensioner pulley to the tensioner arm to rotate the tensioner.

Turn the tensioner device counterclockwise to move the tensioner. This will relieve the tension from the belt. Once the belt has enough slack in it, slide the belt out from under the tensioner pulley.

Lift the belt off each accessory pulley. Slide the belt around the fan blades and out of the engine area.

Lay the old belt next to the new belt to ensure that the new belt is the correct width and length. Slide the belt around the fan blades and around the crankshaft pulley on the bottom of the engine.

Follow the belt routing diagram to position the belt around the air conditioner compressor pulley, the power steering pump pulley, the water pump pulley and the idler pulley. Once the belt is routed inside each accessory pulley, inspect the belt to make sure that it is securely inside the pulleys.

Crank the 1999 Dodge Caravan for 10 to 15 seconds to completely seat the belt ribs in the grooves on each accessory pulley. Shut the engine off and close the hood.

If the belt routing diagram for the 1999 Dodge Caravan is missing, use a pen and a notepad to draw the exact routing of the old belt and use it when installing the new belt.

Below is the diagram you requested. It's for a 3.3L with AC. If you need the diagram without AC, post back with the request and I'll track it down 4 you. Best of luck!
Greg

99 Caravan 3.3L Serpentine Belt

The belt routing diagram is located on the top radiator cross member by the hood latch. You should see it when you open the hood. If it is not there, all Chrysler, Dodge, and Plymouth minivans, from 1993 to at least 1999, used the same 3.3L engine setup, so find someone with one and look for the diagram where I described.