Question about 2003 Honda CR-V

2 Answers

Hi, I would like to know if the front seat belt retractors for Honda CRV 2003 are the same? If yes, is it difficult to replace the seat belt assembly? I'm planning to buy a used front passenger side seat belt for my 03 CRV and i want ot fix it by mself to save money. Your answer would be appreciated..Thanks, Jon

Posted by on

  • Sky Wanderer
    Sky Wanderer Dec 14, 2017

    If you need to replace the seat belt, it is not expensive and without extra problems, then order herehttps://www.safetyrestore.com/honda-seat... They give a guarantee and do everything quickly.

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Whoa whoa whoa, all Honda vehicles before 2007 have a lifetime warranty on seatbelts and seat belt buckles. If you really want to save money go to the dealership.

Posted on Dec 12, 2017

Ad

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 5,274 Answers

I don't know if this is something you want to get into? You decide. Front Seat Belt Replacement SRS components are located in this area. Review the SRS component locations and the precautions and procedures before performing repairs or service.
NOTE: Check the front seat belts for damage, and replace them if necessary.

Front Seat Belt

  1. Make sure you have the anti-theft code for the radio, and then write down the frequencies for the preset buttons.
  2. Disconnect the negative cable from the battery, and wait at least 3 minutes before beginning work.
  3. Slide the front seat forward fully.
  1. Pull the lower anchor cover (A) back, and remove the lower anchor bolt (B).
  2. Remove the B-pillar lower trim panel.

  1. Remove the upper anchor cover (A), and remove the upper anchor bolt (B).

  1. Disconnect the seat belt tensioner connector (A), and detach the harness clip (B) from the retractor (C). Remove the upper retractor mounting bolt (D), and the lower retractor bolt (E), then remove the front seat belt (F) and retractor.
  2. If necessary, remove the front seat belt protector (G).
  3. Remove the B-pillar upper trim.

  1. Remove the shoulder anchor adjuster (A).

  1. Install the seat belt in the reverse order of removal, and note these items:
    • Assemble the washers, collar, and bushing on the upper and lower anchor bolts as shown.
    • Check that the retractor locking mechanism functions.
    • Apply liquid thread lock to the anchor bolts before reinstallation.
    • If the seat belt tensioner has been activated, replace the front seat belt protector with a new one.
    • Before installing the anchor bolts, make sure there are no twists or kinks in the seat belt.
    • Make sure the seat belt tensioner connector is plugged in properly.
    • Reconnect the negative cable to the battery.
    • Enter the anti-theft code for the radio, and then enter the customer's radio station presets.
    • Reset the clock.
    • Do the PCM idle learn procedure and the power window control unit reset procedure.
Upper anchor bolt installation
Lower anchor bolt installation

Seat Belt Buckle

  1. Make sure you have the anti-theft code for the radio, and then write down the frequencies for the preset buttons.
  2. Disconnect the negative cable from the battery, and wait at least 3 minutes before beginning work.
  3. Remove the front seat.
  4. If equipped, remove the center table.
  5. Remove the under seat storage box.
  6. Remove the center cover, driver's, passenger's.
  1. Driver's: If equipped with seat heater, remove the harness band (A), and disconnect the seat subharness connector (B). If equipped without seat heater, detach the seat belt switch connector clip (C). Detach the seat belt buckle tensioner clip (D), and harness clip (E).

Posted on Dec 11, 2017

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Anonymous

  • 5 Answers

SOURCE: How to change the whole headlight assembly on a 05 Honda CRV

When you raise the hood, look for a Phillips screw that holds the parking lamp in. if it is there remove screw and pull parking lamp toward front of vehicle. If headlamp and side lamp are 1 piece, there should be 2 number 10 mm headed bolts that are vertical, that hold the assembly in. The side lamp will have a stud that holds the light to the fender. You may have to pry it loose. Reverse procedure to install.

Posted on Dec 23, 2008

Anonymous

  • 333 Answers

SOURCE: Replace Timing Chain for 2003 Honda CRV?

Rule of thumb this is a timeing belt and it should be changed every 75,000 mile as a general practice. I hope this helps, dont forget to rate my answer, thanks

Posted on Feb 20, 2009

Anonymous

  • 8 Answers

SOURCE: 1999 Honda crv timing belt replacement

1. Remove the 14mm bolt.
2. Remove the spring holding onto the tensioner
3. Remove the tensioner
4. Installation is the reverse.

I install a new tensioner with every timing belt job.

If you have more than 130K miles, I would replace the cam seals. Its extra insurance against future leaks.

Posted on Mar 22, 2009

Anonymous

  • 77 Answers

SOURCE: '04 honda crv bulb change

Its a 5 Watt light bulb. Just pull it out and take it to the store with you. Just remove the license plate to get to it.

Posted on May 21, 2009

henryj1953

  • 396 Answers

SOURCE: SEAT BELT RETRACTOR NO WORK

Then rewind spring is broken. Just have to replace the whole unit. Try the junkyard.

Posted on Jan 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

91 honda accord ex driver seat belt won't retract back into lock position


Take the cover off the belt retractor and see if anything is lodged in the retractor, if not then the belt must be replaced, attempt no repair.

Sep 30, 2016 | Honda Cars & Trucks

1 Answer

I can't find a 94 corolla rh front seat belt retractor, is there a different year or model of toyota seat belt retractors I can use?


seat belts are not genuine but are made to toyota specs
unless there is a problem in the mounting point , most are a bolt on part to a bracket in the car
go to a wreckers that has toyota wrecks and get good belts from cars that have not been involved in front end collisions
most belts fit a range of years and models across toyota and similar shaped cabins

Oct 25, 2017 | Cars & Trucks

1 Answer

Seal belts on both front seats (driver side and passenger side) will not pull out of the retractor. Don't want a fine for not wearing belt but it won't work. No one seems to know how to fix it. ...


No one can fix it!

Don't you find that odd?

You remove the plastic seat belt retractor covers,
on the floor by the "B" Piller

If you need to replace them, the retractors I mean, there
is a special GM Torx Driver Bit for seat belts

I would play around with them to see what the issues are

IF THEY HAVE AN AIR BAG INVOLVED e.g. SRS
System integrated into the seat belts,disconnect the battery
(before) you even think of going near the covers

Jul 01, 2011 | Cadillac DeVille Cars & Trucks

1 Answer

91 honda ex, passenger front seat belt is not working and the light in the dash board keeps lit, I have check the fuses for it, and all the connection to the belt and it seems all intact...any advise?


Your 1991 model Accord has automatic front retracting shoulder belts and, more than likely, the power retractor motor has gone bad on the passenger side front. If the shoulder seat belt is not in the retracted position, up close against the seat, when the car is running, the seat belt light will stay lit on your dash. Have the seat belt motor inspected and replaced if necessary.

Oct 18, 2010 | 1990 Honda Accord

1 Answer

When not in use seat belt does not retract fully


the springs inside the seat belt retractors wear out over time. remove the trim from over the retractor and make sure nothing is rubbing the belt, and if it all looks alright, replace the seat belt.

Feb 17, 2010 | 1997 Honda Accord

1 Answer

I need to replace a rear seat belt in a 1997 Ford Tarsus. Does any know the best way to access the assembly? In addition, are there any diagrams available that show the connection points?


please don't forget to rate, thx.

Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Safety Belt Bolt Bit T77L-2100A
NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.

Removal
  1. Remove rear seat cushion. Refer to Section 01-10 .
Seat Cushion, Rear Sedan
Removal
  1. Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
  1. Remove rear seat cushion from vehicle.
  1. Remove rear seat back. Refer to Section 01-10 .
Seat Back, Rear 60/40 Split Bench—Sedan
Removal
  1. NOTE: Safety belt bolts do not secure seat back to vehicle.

    Remove rear seat cushion as described.
  1. Fold down back seat and remove two bolts in the center of each seat back striker plates.
  1. Remove two bolts from outboard rear seat back frame retaining brackets.
  1. Lift seat back up and pull forward to remove from vehicle.
  1. Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
Trim Panel, Quarter—Sedan Removal
  1. Remove rear seat. Refer to Section 01-10 .
  1. Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
  1. Pull lower quarter trim panel away from body.
  1. Remove safety belt retaining bolt.
  1. Feed safety belt through lower quarter trim panel.
  1. Remove safety belt anchor plate-to-sill bolt from quarter panel.
  1. Remove retractor anchor nut and retractor from rear quarter panel.
  1. Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
  1. Slide anchor plate end of safety belt through the openings in the quarter trim panel.
  1. Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.


    2a6fac0.gif


    Item Part Number Description 1 386277-S190 Bolt (Part of 611B68) 2 31012 Upper Rear Quarter Trim Panel 3 611B60 Retractor and Tongue 4 N800937-S190 Nut 5 389370-S190 Bolt 6 — Rear Quarter Panel (Part of Body) 7 52018 Lower Rear Quarter Trim Panel 8 — Mounting Stud (Part of Body)
  1. Remove seat belt anchor bolt and retractor and tongue from rear deck panel.


    fff90b0.gif

Installation
  1. To install, reverse Removal procedure.
  1. Make sure the safety belt webbing is not twisted. If it is, remove the twist.
  1. Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
  1. Check the restraint system for proper operation.

Jun 30, 2009 | 1997 Ford Taurus

1 Answer

2003 mustang: do my new seat belts work?


yes bolt them in and they will start working

May 08, 2009 | 2003 Ford Mustang

1 Answer

How do we fix front passenger side seat belt retractor on 1999 Ford Taurus? It will not pull out....


you may have to remove the bolt that holds the buckle to the floor. Try to push the belt into the retractor and see if it frees up.

I assume you are saying it is in the locked mode. It has an automatic lock mode for holding a child seat. When the belt is pulled all the way out, it goes into locking mode. You will hear it ratchet when the belt starts going back in.



Section 01-20A: Restraints, Active 1999 Taurus, Sable Workshop Manual
DESCRIPTION AND OPERATION Safety Belt, Lap/Shoulder The dual locking mode retractor on the shoulder belt portion of the combination lap/shoulder safety belt for the front seat passenger and rear seat outboard passengers operates in two ways:
  1. In the vehicle sensitive (emergency locking) mode, the shoulder belt retractor will allow the occupant freedom of movement, locking tight only on hard braking, hard cornering or impacts of approximately 8 km/h (5 mph) or more. The front and rear outboard seat belt retractors can also be made to lock by pulling/jerking on the belt.
  1. In the automatic locking mode, the shoulder belt retractor will be automatically locked and remain locked when the combination lap/shoulder safety belt is buckled and does not allow the occupant freedom of movement. This mode provides tight lap/shoulder belt fit on the occupant and on a child safety seat or infant carrier installation restraint.
  1. When the combination lap/shoulder belt is unbuckled and allowed to retract completely, the retractor will switch to the vehicle sensitive (emergency) locking mode.
sxh~us~en~file=ani_caut.gif~gen~ref.gif WARNING: REAR-FACING INFANT SEATS SHOULD NEVER BE PLACED IN THE FRONT SEATS.
The automatic locking mode must be used when installing a child safety seat on the front passenger seat and rear outboard seats where dual locking retractors are provided

Apr 21, 2009 | 1999 Ford Taurus

1 Answer

Replace Timing Chain for 2003 Honda CRV?


Rule of thumb this is a timeing belt and it should be changed every 75,000 mile as a general practice. I hope this helps, dont forget to rate my answer, thanks

Feb 20, 2009 | 2003 Honda CR-V

1 Answer

Seat Belt repair/replace


  1. Remove front seat.
  2. Remove adjuster cover. A
  3. Slide floor anchor cover.
  4. Remove floor anchor bolt. B
  5. Remove shoulder anchor bolt. C
  6. Remove front and rear kicking plate, then remove center pillar upper and lower garnish.
  7. Disconnect seat belt pre-tensioner connector.
  8. Remove the screw securing seat belt pre-tensioner retractor, then remove seat belt and seat belt pre-tensioner retractor.
  9. Remove bolts securing seat belt adjuster, then remove seat belt adjuster. Reverse procedure to install.J

Nov 03, 2008 | 2000 Nissan Maxima

Not finding what you are looking for?
2003 Honda CR-V Logo

Related Topics:

195 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...