Hi.
the fob probably needs to be rematched to the car again.
EASY>>>>>
Reprogramming an X-Type Key Fob.
Step 1
Open the
driver side door.
Step 2
Turn the ignition switch to the
'auxiliary' position, then turn the ignition switch to the 'ON' position and
back to the 'auxiliary' position four times. *This must be done fairly quickly.
If you have done it correctly, you will hear a chime come from the
GEM*
Step 3
Turn the ignition switch to 'OFF' position.
Step
4
Remove the key from the ignition.
Step 5
To program the
transmitter, press any key within ten seconds. **If it worked, you should hear
another chime come from the GEM**
Step 6
Close the door...YOU'RE
DONE!
I have done this on my dads x type. it does work. do not forget to have the drivers door open like i did.
SOURCE: how do you change battery in key fob on 2002 vw golf
No problem. The key fob is two pieces. The key part and the remote. Open the key as you would to sue it. Where the key flips open you can see a small recess about where the line of the trunck switch. This is where the key separates. You can pull it off or pry it with a small screwdriver. Once separated with remote part in your hand this also splits in 2. In the same area you split the key off insert the screwdriver in this recess and the fob will open giving you access to the battery. Also can be done by hand. It is a little tight so you will have to force which is normal. No screws just clipped. Make sure the battery is positioned in the right way and that you have 3 volts when you test the battery. 2.7 volts will make the remote not work or act funny.
SOURCE: renault megane key fob wont work
I had the same problem with mine
your key fob is now out of sync with the ECU to sync them just follow this link (renault will charge up to £180 for new key and to sync it)
http://renaulthelp.110mb.com/ImmBypass.html
SOURCE: key fob will not undo
If you don't have one that works for the vehicle now, you'll have to take it to your local dealer to have it programmed to the vehicle. Some will charge for this, some will do it at no charge.
If you do have a remote that is programmed and working for the vehicle, then the following steps will allow you to program another remote:
1. Enter vehicle and close all doors.
2. Put seatbelt on (or clip it into the buckle) to shut the warning buzzer off.
3. Put key in ignition, turn to run position but don't start it.
4. Press and hold the unlock button on the working key fob and hold for 4 seconds, then also press the panic button.
5. Release both buttons and you should hear a single chime to indicate it is in program mode. You have 30 seconds after the chime to program any additional remotes you want to program.
6. Press and release both the unlock and lock buttons simultaneously on the remote you are programming. You should hear another single chime.
7. Within 4 seconds after hearing the chime, press either lock or unlock button on remote that you are programming.
SOURCE: key fob not working after battery change ford focus 2006
Try reprogramming it.
1. Turn the ignition from OFF to RUN 4 times within 6 seconds.
2. Turn the ignition OFF. The system will chime to confirm programming mode.
3. Within 20 seconds, press any button on first keyless remote.
The system will chime once to confirm programming.
4. Within 20 seconds, press any button on second keyless remote.
System will chime once to confirm programming.
5. Turn ignition to RUN to exit programming mode.
SOURCE: renault key fob doesnt work
Hi.
I have a clio II, 2001, i have the same problem and i fixed it.
Don't know if will work for you but here it goes:
1 - no key in ingnition
2 - press the unlock button in console off the car for about 10 seconds(dont let go)
3 - it should work the central doors one time and then 2 times( hear)
4 - press the remote a few times until it starts working
It worked for me hope the same for you.
Please tell me if it worked and pass the message.
Good luck
855 views
Usually answered in minutes!
×